Hostname: page-component-cd9895bd7-hc48f Total loading time: 0 Render date: 2024-12-23T12:14:53.388Z Has data issue: false hasContentIssue false
  • English
  • Français

Enhancing the tensile and ignition response of monolithic magnesium by reinforcing with silica nanoparticulates

Published online by Cambridge University Press:  29 May 2017

Gururaj Parande ,
Vyasaraj Manakari ,
Ganesh Kumar Meenashisundaram  and
Manoj Gupta
Gururaj Parande
Affiliation:
Department of Mechanical Engineering, National University of Singapore, Singapore 117576, Singapore
Vyasaraj Manakari
Affiliation:
Department of Mechanical Engineering, National University of Singapore, Singapore 117576, Singapore
Ganesh Kumar Meenashisundaram
Affiliation:
Department of Mechanical Engineering, National University of Singapore, Singapore 117576, Singapore
Manoj Gupta*
Affiliation:
Department of Mechanical Engineering, National University of Singapore, Singapore 117576, Singapore
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Low volume fraction (0.5, 1, and 2 vol%) SiO2 reinforced magnesium nanocomposites were synthesized using powder metallurgy technique followed by hot extrusion. The nanocomposites were studied for physical, microstructural, ignition, and mechanical properties to study the influence of nanoparticulate addition on monolithic magnesium. The grain size of the developed nanocomposites was observed to marginally decrease with the addition of SiO2 nanoparticulates with 2 vol% SiO2 addition resulting in a grain size of ∼23 μm which is ∼32% lower than that of pure Mg. The ignition temperature of pure Mg was enhanced with the addition of SiO2 nanoparticulates with Mg 2 vol% SiO2 nanocomposite exhibiting an ignition temperature of 611 °C (∼20 °C greater than pure Mg and AZ31 alloy). Under room temperature tensile loading, Hall–Petch strengthening mechanism was the most dominant wherein the addition of SiO2 nanoparticulates to pure magnesium enhances the strength within 0–2 vol% range and ductility in 0–1 vol% range.

Keywords

Mggrain sizethermogravimetric analysis (TGA)
Type
Articles
Information
Journal of Materials Research , Volume 32 , Issue 11 , 14 June 2017 , pp. 2169 - 2178
Check for updates
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Michele Manuel

References

REFERENCES

Davy, H.: Electro-chemical researches, on the decomposition of the earths; with observations on the metals obtained from the alkaline earths, and on the amalgam procured from ammonia. Philos. Trans. R. Soc. London 98, 333 (1808).Google Scholar
Avedesian, M.M. and Baker, H.: ASM Specialty Handbook: Magnesium and Magnesium Alloys (ASM International, Materials Park, 1999).Google Scholar
Winzer, N., Atrens, A., Song, G., Ghali, E., Dietzel, W., Kainer, K.U., Hort, N., and Blawert, C.: A critical review of the stress corrosion cracking (SCC) of magnesium alloys. Adv. Eng. Mater. 7, 659 (2005).Google Scholar
Song, G.L. and Atrens, A.: Corrosion mechanisms of magnesium alloys. Adv. Eng. Mater. 1, 11 (1999).Google Scholar
Jun, J., Kim, J., Park, B., Kim, K., and Jung, W.: Effects of rare earth elements on microstructure and high temperature mechanical properties of ZC63 alloy. J. Mater. Sci. 40, 2659 (2005).Google Scholar
Itoi, T., Takahashi, K., Moriyama, H., and Hirohashi, M.: A high-strength Mg–Ni–Y alloy sheet with a long-period ordered phase prepared by hot-rolling. Scr. Mater. 59, 1155 (2008).Google Scholar
Toda-Caraballo, I., Galindo-Nava, E.I., and Rivera-Díaz-del-Castillo, P.E.: Understanding the factors influencing yield strength on Mg alloys. Acta Mater. 75, 287 (2014).Google Scholar
Johnston, S., Shi, Z., and Atrens, A.: The influence of pH on the corrosion rate of high-purity Mg, AZ91 and ZE41 in bicarbonate buffered Hanks’ solution. Corros. Sci. 101, 182 (2015).Google Scholar
Song, G. and Atrens, A.: Understanding magnesium corrosion—A framework for improved alloy performance. Adv. Eng. Mater. 5, 837 (2003).Google Scholar
Atrens, A., Liu, M., and Zainal Abidin, N.I.: Corrosion mechanism applicable to biodegradable magnesium implants. Mater. Sci. Eng., B 176, 1609 (2011).Google Scholar
Atrens, A., Song, G-L., Cao, F., Shi, Z., and Bowen, P.K.: Advances in Mg corrosion and research suggestions. J. Magnesium Alloys 1, 177 (2013).Google Scholar
Atrens, A., Song, G-L., Liu, M., Shi, Z., Cao, F., and Dargusch, M.S.: Review of recent developments in the field of magnesium corrosion. Adv. Eng. Mater. 17, 400 (2015).Google Scholar
Gehrmann, R., Frommert, M.M., and Gottstein, G.: Texture effects on plastic deformation of magnesium. Mater. Sci. Eng., A 395, 338 (2005).Google Scholar
Umeda, J., Kawakami, M., Kondoh, K., Ayman, E.L.S., and Imai, H.: Microstructural and mechanical properties of titanium particulate reinforced magnesium composite materials. Mater. Chem. Phys. 123, 649 (2010).Google Scholar
Seetharaman, S., Subramanian, J., Tun, K., Hamouda, A., and Gupta, M.: Synthesis and characterization of nano boron nitride reinforced magnesium composites produced by the microwave sintering method. Materials 6, 1940 (2013).Google Scholar
Ferguson, J., Sheykh-Jaberi, F., Kim, C-S., Rohatgi, P.K., and Cho, K.: On the strength and strain to failure in particle-reinforced magnesium metal–matrix nanocomposites (Mg MMNCs). Mater. Sci. Eng., A 558, 193 (2012).Google Scholar
Tan, Q., Atrens, A., Mo, N., and Zhang, M-X.: Oxidation of magnesium alloys at elevated temperatures in air: A review. Corros. Sci. 112, 734–759 (2016).Google Scholar
Yu, X., Jiang, B., Yang, H., Yang, Q., Xia, X., and Pan, F.: High temperature oxidation behavior of Mg–Y–Sn, Mg–Y, Mg–Sn alloys and its effect on corrosion property. Appl. Surf. Sci. 353, 1013 (2015).Google Scholar
Liu, M., Shih, D.S., Parish, C., and Atrens, A.: The ignition temperature of Mg alloys WE43, AZ31 and AZ91. Corros. Sci. 54, 139 (2012).Google Scholar
Prasad, A., Shi, Z., and Atrens, A.: Influence of Al and Y on the ignition and flammability of Mg alloys. Corros. Sci. 55, 153 (2012).Google Scholar
Prasad, A., Shi, Z., and Atrens, A.: Flammability of Mg–X binary alloys. Adv. Eng. Mater. 14, 772 (2012).Google Scholar
Boris, P.: A study of the flammability of magnesium (Federal Aviation Administration Washington DC Systems Research and Development Service, DTIC Document, 1964).Google Scholar
Marker, T.: Evaluating the Flammability of Various Magnesium Alloys during Laboratory-and Full-scale Aircraft Fire Tests (DOT/FAA/AR-11/3; US Department of Transportation, Federal Aviation Administration, Atlantic City, 2013).Google Scholar
Tekumalla, S. and Gupta, M.: An insight into ignition factors and mechanisms of magnesium based materials: A review. Mater. Des. 113, 84 (2017).Google Scholar
Lin, P-y., Zhou, H., Sun, N., Li, W-p., Wang, C-t., Wang, M-x., Guo, Q-c., and Li, W.: Influence of cerium addition on the resistance to oxidation of AM50 alloy prepared by rapid solidification. Corros. Sci. 52, 416 (2010).Google Scholar
Arrabal, R., Pardo, A., Merino, M., Mohedano, M., Casajús, P., Paucar, K., and Matykina, E.: Oxidation behavior of AZ91D magnesium alloy containing Nd or Gd. Oxid. Met. 76, 433 (2011).Google Scholar
Lee, J-K. and Kim, S.K.: Effect of CaO addition on the ignition resistance of Mg-Al alloys. Mater. Trans. 52, 1483 (2011).Google Scholar
Nguyen, T.D. and Lee, D.B.: Oxidation of AM60B Mg alloys containing dispersed SiC particles in air at temperatures between 400 and 550 °C. Oxid. Met. 73, 183 (2009).Google Scholar
Meenashisundaram, G.K. and Gupta, M.: Emerging environment friendly, magnesium-based composite technology for present and future generations. JOM 68, 1890 (2016).CrossRefGoogle Scholar
Flörke, O.W., Graetsch, H.A., Brunk, F., Benda, L., Paschen, S., Bergna, H.E., Roberts, W.O., Welsh, W.A., Libanati, C., Ettlinger, M., Kerner, D., Maier, M., Meon, W., Schmoll, R., Gies, H., and Schiffmann, D.: Silica, Ullmann’s Encyclopedia of Industrial Chemistry (Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim, 2000).Google Scholar
Fanderlik, I.: Silica Glass and its Application (Elsevier, New York, 2013).Google Scholar
Wan, Y., Cui, T., Li, W., Li, C., Xiao, J., Zhu, Y., Ji, D., Xiong, G., and Luo, H.: Mechanical and biological properties of bioglass/magnesium composites prepared via microwave sintering route. Mater. Des. 99, 521 (2016).Google Scholar
Parande, G., Manakari, V., Meenashisundaram, G.K., and Gupta, M.: Enhancing the hardness/compression/damping response of magnesium by reinforcing with biocompatible silica nanoparticulates. Int. J. Mater. Res. 107, 1091 (2016).Google Scholar
Kang, X., Zhang, J., Zhang, Q., Du, K., and Tang, Y.: Studies on ignition and afterburning processes of KClO4/Mg pyrotechnics heated in air. J. Therm. Anal. Calorim. 109, 1333 (2011).Google Scholar
German, R.M.: Powder Metallurgy Science (Metal Powder Industries Federation, Princeton, NJ, USA, 1984); p. 279.Google Scholar
Mirza, F. and Chen, D.: A unified model for the prediction of yield strength in particulate-reinforced metal matrix nanocomposites. Materials 8, 5138 (2015).Google Scholar
Stanford, N., Atwell, D., Beer, A., Davies, C., and Barnett, M.: Effect of microalloying with rare-earth elements on the texture of extruded magnesium-based alloys. Scr. Mater. 59, 772 (2008).Google Scholar
Bansal, N.P. and Doremus, R.H.: Handbook of Glass Properties (Elsevier, Orlando, 2013).Google Scholar
Shackelford, J.F., Han, Y-H., Kim, S., and Kwon, S-H.: CRC Materials Science and Engineering Handbook (CRC Press, Boca Raton, Florida, 2016).CrossRefGoogle Scholar
Meenashisundaram, G.K., Nai, M.H., Almajid, A., and Gupta, M.: Development of high performance Mg–TiO2 nanocomposites targeting for biomedical/structural applications. Mater. Des. 65, 104 (2015).Google Scholar
Jayalakshmi, S., Sankaranarayanan, S., Koh, S., and Gupta, M.: Effect of Ag and Cu trace additions on the microstructural evolution and mechanical properties of Mg–5Sn alloy. J. Alloys Compd. 565, 56 (2013).Google Scholar
Tun, K.S., Jayaramanavar, P., Nguyen, Q.B., Chan, J., Kwok, R., and Gupta, M.: Investigation into tensile and compressive responses of Mg–ZnO composites. Mater. Sci. Technol. 28, 582 (2013).Google Scholar
Koike, J., Kobayashi, T., Mukai, T., Watanabe, H., Suzuki, M., Maruyama, K., and Higashi, K.: The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys. Acta Mater. 51, 2055 (2003).Google Scholar
Supplementary material: File

Parande supplementary material

Parande supplementary material 1

Download Parande supplementary material(File)
File 44.8 KB