Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-22T07:21:41.981Z Has data issue: false hasContentIssue false

Enhanced energy density and electric cycling reliability via MnO2 modification in sodium niobate-based relaxor dielectric capacitors

Published online by Cambridge University Press:  27 October 2020

Letao Yang
Affiliation:
Institute for Superconducting and Electronic Materials, AIIM, University of Wollongong, NSW2500, Australia
Xi Kong
Affiliation:
Institute for Superconducting and Electronic Materials, AIIM, University of Wollongong, NSW2500, Australia
Zhenxiang Cheng
Affiliation:
Institute for Superconducting and Electronic Materials, AIIM, University of Wollongong, NSW2500, Australia
Shujun Zhang*
Affiliation:
Institute for Superconducting and Electronic Materials, AIIM, University of Wollongong, NSW2500, Australia
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Sodium niobate (NaNbO3)-based dielectrics have received much attention for energy storage applications due to their low-cost, lightweight, and nontoxic nature. The field-induced metastable ferroelectric phase in NaNbO3-based dielectrics, however, leads to a large hysteresis of the polarization–electric field (PE) loops and hence deteriorate the energy storage performance. In this study, the hysteresis was successfully reduced by introducing Bi3+ and Ti4+ into A-site and B-site of NaNbO3, respectively. MnO2 addition was added to further increase the ceramic density and enhance the cycling reliability. As a result, a high recoverable energy density of 4.3 J/cm3 and a high energy efficiency of 90% were simultaneously achieved in the ceramic capacitor at an applied electric field of 360 kV/cm. Of particular importance is that the ceramic capacitor exhibits a stable energy storage properties over a wide temperature range of −70 to 170 °C, with much improved electric cycling reliability up to 105 cycles.

Type
Article
Copyright
Copyright © The Author(s), 2020, published on behalf of Materials Research Society by Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Yao, Z., Song, Z., Hao, H., Yu, Z., Cao, M., Zhang, S., Lanagan, M.T., and Liu, H.: Homogeneous/inhomogeneous-structured dielectrics and their energy-storage performances. Adv. Mater. 29, 1601727 (2017).CrossRefGoogle ScholarPubMed
Yang, L., Kong, X., Li, F., Hao, H., Cheng, Z., Liu, H., Li, J-F., and Zhang, S.: Perovskite lead-free dielectrics for energy storage applications. Prog. Mater. Sci. 102, 72 (2019).CrossRefGoogle Scholar
Liu, Z., Lu, T., Ye, J., Wang, G., Dong, X., Withers, R., and Liu, Y.: Antiferroelectrics for energy storage applications: A review. Adv. Mater. Technol. 3, 1800111 (2018).CrossRefGoogle Scholar
Hao, X.: A review on the dielectric materials for high energy-storage application. J. Adv. Dielectr. 3, 1330001 (2013).CrossRefGoogle Scholar
Tan, D., Zhang, L., Chen, Q., and Irwin, P.: High-temperature capacitor polymer films. J. Electron. Mater. 43, 4569 (2014).CrossRefGoogle Scholar
Li, Q. and Cheng, S.: Polymer nanocomposites for high-energy-density capacitor dielectrics: Fundamentals and recent progress. IEEE Electr. Insul. Mag. 36, 7 (2020).CrossRefGoogle Scholar
Cohen, R.E.: Origin of ferroelectricity in perovskite oxides. Nature 358, 136 (1992).CrossRefGoogle Scholar
Wu, L.W., Wang, X.H., and Li, L.T.: Lead-free BaTiO3-Bi(Zn2/3Nb1/3)O3 weakly coupled relaxor ferroelectric materials for energy storage. RSC Adv. 6, 14273 (2016).CrossRefGoogle Scholar
Zhou, M., Liang, R., Zhou, Z., and Dong, X.: Novel BaTiO3-based lead-free ceramic capacitors featuring high energy storage density, high power density, and excellent stability. J. Mater. Chem. C 6, 8528 (2018).CrossRefGoogle Scholar
Zhao, P.Y., Wang, H.X., Wu, L.W., Chen, L.L., Cai, Z.M., Li, L.T., and Wang, X.H.: High-performance relaxor ferroelectric materials for energy storage applications. Adv. Energy Mater. 9, 1803048 (2019).CrossRefGoogle Scholar
Kong, X., Yang, L., Cheng, Z., and Zhang, S.: Bi-modified SrTiO3-based ceramics for high-temperature energy storage applications. J. Am. Ceram. Soc. 103, 1722 (2019).CrossRefGoogle Scholar
Wang, G., Li, J.L., Zhang, X., Fan, Z.M., Yang, F., Feteira, A., Zhou, D., Sinclair, D.C., Ma, T., Tan, X.L., Wang, D.W., and Reaney, I.M.: Ultrahigh energy storage density lead-free multilayers by controlled electrical homogeneity. Energy Environ. Sci. 12, 582 (2019).CrossRefGoogle Scholar
Yang, L., Kong, X., Cheng, Z., and Zhang, S.: Ultra-high energy storage performance with mitigated polarization saturation in lead-free relaxors. J. Mater. Chem. A 7, 8573 (2019).CrossRefGoogle Scholar
Wang, D.W., Fan, Z.M., Zhou, D., Khesro, A., Murakami, S., Feteira, A., Zhao, Q.L., Tan, X.L., and Reaney, I.M.: Bismuth ferrite-based lead-free ceramics and multilayers with high recoverable energy density. J. Mater. Chem. A 6, 4133 (2018).CrossRefGoogle Scholar
Wang, G., Lu, Z., Yang, H., Ji, H., Mostaed, A., Li, L., Wei, Y., Feteira, A., Sun, S., Sinclair, D.C., Wang, D., and Reaney, I.M.: Fatigue resistant lead-free multilayer ceramic capacitors with ultrahigh energy density. J. Mater. Chem. A 8, 11414 (2020).CrossRefGoogle Scholar
Li, J., Li, F., Xu, Z., and Zhang, S.: Multilayer lead-free ceramic capacitors with ultrahigh energy density and efficiency. Adv. Mater. 30, 1802155 (2018).CrossRefGoogle Scholar
Li, J., Shen, Z., Chen, X., Yang, S., Zhou, W., Wang, M., Wang, L., Kou, Q., Liu, Y., Li, Q., Xu, Z., Chang, Y., Zhang, S., and Li, F.: Grain-orientation-engineered multilayer ceramic capacitors for energy storage applications. Nat Mater. 19, 999 (2020).Google ScholarPubMed
Yang, L., Kong, X., Cheng, Z., and Zhang, S.: Enhanced energy storage performance of sodium niobate-based relaxor dielectrics by a ramp-to-spike sintering profile. ACS Appl. Mater. Interfaces 12, 32834 (2020).CrossRefGoogle ScholarPubMed
Zhou, M.X., Liang, R.H., Zhou, Z.Y., and Dong, X.L.: Superior energy storage properties and excellent stability of novel NaNbO3-based lead-free ceramics with A-site vacancy obtained via a Bi2O3 substitution strategy. J. Mater. Chem. A 6, 17896 (2018).CrossRefGoogle Scholar
Ye, J., Wang, G., Zhou, M., Liu, N., Chen, X., Li, S., Cao, F., and Dong, X.: Excellent comprehensive energy storage properties of novel lead-free NaNbO3-based ceramics for dielectric capacitor applications. J. Mater. Chem. C 7, 5639 (2019).CrossRefGoogle Scholar
Pan, H., Li, F., Liu, Y., Zhang, Q., Wang, M., Lan, S., Zheng, Y., Ma, J., Gu, L., Shen, Y., Yu, P., Zhang, S., Chen, L-Q., Lin, Y-H., and Nan, C-W.: Ultrahigh-energy density lead-free dielectric films via polymorphic nanodomain design. Science 365, 578 (2019).CrossRefGoogle ScholarPubMed
Fu, Z., Chen, X., Li, Z., Hu, T., Zhang, L., Lu, P., Zhang, S., Wang, G., Dong, X., and Xu, F.: Unveiling the ferrielectric nature of PbZrO3-based antiferroelectric materials. Nat. Commun. 11, 3809 (2020).CrossRefGoogle ScholarPubMed
Bersuker, I.B.: Pseudo Jahn-Teller origin of perovskite multiferroics, magnetic-ferroelectric crossover, and magnetoelectric effects: The d 0-d 10 problem. Phys. Rev. Lett. 108, 137202 (2012).CrossRefGoogle ScholarPubMed
Gao, J., Zhang, Y., Zhao, L., Lee, K-Y., Liu, Q., Studer, A., Hinterstein, M., Zhang, S., and Li, J-F.: Enhanced antiferroelectric phase stability in La-doped AgNbO3: Perspectives from the microstructure to energy storage properties. J. Mater. Chem. A 7, 2225 (2019).CrossRefGoogle Scholar
Luo, N., Han, K., Zhuo, F., Xu, C., Zhang, G., Liu, L., Chen, X., Hu, C., Zhou, H., and Wei, Y.: Aliovalent A-site engineered AgNbO3 lead-free antiferroelectric ceramics toward superior energy storage density. J. Mater. Chem. A 7, 14118 (2019).CrossRefGoogle Scholar
Zhao, L., Liu, Q., Gao, J., Zhang, S., and Li, J.F.: Lead-free antiferroelectric silver niobate tantalate with high energy storage performance. Adv. Mater. 29, 1701824 (2017).CrossRefGoogle ScholarPubMed
Cross, L.E. and Nicholson, B.J.: The optical and electrical properties of single crystals of sodium niobate. Philos. Mag. A 46, 453 (1955).CrossRefGoogle Scholar
Shirane, G., Newnham, R., and Pepinsky, R.: Dielectric properties and phase transitions of NaNbO3 and (Na,K)NbO3. Phys. Rev. 96, 581 (1954).CrossRefGoogle Scholar
Dungan, R.H. and Golding, R.D.: Metastable ferroelectric sodium niobate. J. Am. Ceram. Soc. 47, 73 (1964).CrossRefGoogle Scholar
Wood, E.A., Miller, R.C., and Remeika, J.P.: The field-induced ferroelectric phase of sodium niobate. Acta Cryst. 15, 1273 (1962).CrossRefGoogle Scholar
Shimizu, H., Guo, H., Reyes-Lillo, S.E., Mizuno, Y., Rabe, K.M., and Randall, C.A.: Lead-free antiferroelectric: xCaZrO-(1-x)NaNbO3 system (0 ≤ x ≤ 0.10). Dalton Trans. 44, 10763 (2015).CrossRefGoogle Scholar
Gao, L., Guo, H., Zhang, S., and Randall, C.A.: Stabilized antiferroelectricity in xBiScO-(1-x)NaNbO3 lead-free ceramics with established double hysteresis loops. Appl. Phys. Lett. 112, 092905 (2018).CrossRefGoogle Scholar
Chao, L., Hou, Y., Zheng, M., and Zhu, M.: High dense structure boosts stability of antiferroelectric phase of NaNbO3 polycrystalline ceramics. Appl. Phys. Lett. 108, 212902 (2016).CrossRefGoogle Scholar
Xie, A.W., Qi, H., Zuo, R.Z., Tian, A., Chen, J., and Zhang, S.J.: An environmentally-benign NaNbO3 based perovskite antiferroelectric alternative to traditional lead-based counterparts. J. Mater. Chem. C 7, 15153 (2019).CrossRefGoogle Scholar
Qi, H., Zuo, R., Xie, A., Tian, A., Fu, J., Zhang, Y., and Zhang, S.: Ultrahigh energy-storage density in NaNbO3-based lead-free relaxor antiferroelectric ceramics with nanoscale domains. Adv. Funct. Mater. 29, 1903877 (2019).CrossRefGoogle Scholar
Noguchi, Y., Miyayama, M., and Kudo, T.: Direct evidence of A-site-deficient strontium bismuth tantalate and its enhanced ferroelectric properties. Phys. Rev. B 63, 214102 (2001).CrossRefGoogle Scholar
Megaw, H.D.: The seven phases of sodium niobate. Ferroelectrics 7, 87 (1974).CrossRefGoogle Scholar
Iwasaki, H. and Ikeda, T.: Studies on the system Na(Nb1-xTax)O3. J. Phys. Soc. Jpn. 18, 157 (1963).CrossRefGoogle Scholar
Gao, L., Guo, H., Zhang, S., and Randall, C.A.: A perovskite lead-free antiferroelectric xCaHfO3-(1-x)NaNbO3 with induced double hysteresis loops at room temperature. J. Appl. Phys. 120, 204102 (2016).CrossRefGoogle Scholar
Raevski, I.P. and Prosandeev, S.A.: A new, lead free, family of perovskites with a diffuse phase transition: NaNbO3-based solid solutions. J. Phys. Chem. Solids 63, 1939 (2002).CrossRefGoogle Scholar
Schulze, W.A., Cross, L.E., and Buessem, W.R.: Degradation of BaTiO3 ceramic under high AC electric field. J. Am. Ceram. Soc. 63, 83 (1980).CrossRefGoogle Scholar
Genenko, Y.A., Glaum, J., Hoffmann, M.J., and Albe, K.: Mechanisms of aging and fatigue in ferroelectrics. Mater. Sci. Eng. B 192, 52 (2015).CrossRefGoogle Scholar
Chen, L., Wang, H., Zhao, P., Shen, Z., Zhu, C., Cen, Z., Li, L., and Wang, X.: Effect of MnO2 on the dielectric properties of Nb-doped BaTiO3-(Bi0.5Na0.5)TiO3 ceramics for X9R MLCC applications. J. Am. Ceram. Soc. 102, 2781 (2019).Google Scholar
Zhang, Y. and Li, J-F.: Review of chemical modification on potassium sodium niobate lead-free piezoelectrics. J. Mater. Chem. C 7, 4284 (2019).CrossRefGoogle Scholar
Li, F., Zhang, S., Damjanovic, D., Chen, L-Q., and Shrout, T.R.: Local structural heterogeneity and electromechanical responses of ferroelectrics: Learning from relaxor ferroelectrics. Adv. Funct. Mater. 28, 1801504 (2018).CrossRefGoogle Scholar
Zhang, N., Li, L., Li, B., Guo, D., and Gui, Z.: Improvement of electric fatigue properties in PLZT ferroelectric ceramics due to SrBi2Ta2O9 incorporation. Mater. Sci. Eng. B 90, 185 (2002).CrossRefGoogle Scholar
Zhang, N., Li, L., and Gui, Z.: Improvement of electric fatigue properties in Pb0.94La0.04(Zr0.70Ti0.30)O3 ferroelectric capacitors due to SrBi2Nb2O9 incorporation. Mater. Res. Bull. 36, 2553 (2001).CrossRefGoogle Scholar