Hostname: page-component-586b7cd67f-2plfb Total loading time: 0 Render date: 2024-11-23T14:22:34.649Z Has data issue: false hasContentIssue false
  • English
  • Français

Electromigration Studies of Sn(Cu) and Sn(Ni) Alloy Stripes

Published online by Cambridge University Press:  01 August 2005

C.C. Wei  and
C.Y. Liu
C.C. Wei
Affiliation:
Department of Chemical Engineering and Materials Engineering, National Central University, Chung-Li, Taiwan 320, Republic of China
C.Y. Liu*
Affiliation:
Department of Chemical Engineering and Materials Engineering, and Institute of Materials Science and Engineering, National Central University, Chung-Li, Taiwan 320, Republic of China
*
a) Address all correspondence to this author. e-mail: [email protected].
Get access

Abstract

Using Blech’s structure, we studied the electromigration (EM) behaviors of four different Sn(Cu) and Sn(Ni) alloys, which are Sn, Sn0.7Cu, Sn3.0Cu, and Sn1Ni. The order of the EM rates was determined to be Sn0.7Cu > Sn > Sn3Cu > Sn1Ni. We believe that the lower yielding strength and higher grain boundary density of Sn0.7Cu were the main reasons that Sn0.7Cu had the fastest EM rate. Moreover, we found that the addition at Ni could effectively retard EM. The critical products of Sn, Sn0.7Cu, and Sn3.0Cu, which were determined to be 1500, 500, and 1580 A/cm, respectively. The diffuse-effective charge (DZ*) values of the solder stripes from this present work have same order magnitude of the reported values, which were measured by using actual solder bumps.

Keywords

Packaging
Type
Articles
Information
Journal of Materials Research , Volume 20 , Issue 8 , August 2005 , pp. 2072 - 2079
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1The National Technology Roadmap for Semiconductors (Semiconductor Industry Association, San Jose, CA, 1997).Google Scholar
2Brandenberg, S. and Yeh, S.: Electromigration studies of flip chip bump solder joints, in Surface Mount International Conference and Exposition, SMI 98 Proceeding (1998), p. 337.Google Scholar
3Lee, T.Y. and Tu, K.N.: Electromigration of eutectic SnPb and SnAg3.8Cu0.7 flip chip solder bumps and under-bump metallization. J. Appl. Phys. 90, 4502 (2001).CrossRefGoogle Scholar
4Lee, T.Y., Tu, K.N., Kuo, S.M. and Frear, D.R.: Electromigration of eutectic SnPb solder interconnects for flip chip technology. J. Appl. Phys. 89, 3189 (2001).CrossRefGoogle Scholar
5Hu, Y.C., Lin, Y.H. and Kao, C.R.: Electromigration failure in flip chip solder joints due to rapid dissolution of copper. J. Mater. Res. 18, 2544 (2003).CrossRefGoogle Scholar
6 www.Pb-free.info.Google Scholar
7Lead-Free, NEMI & Environmental Initiatives, www.inemi.org/cms/projects/ese/lf_hottopics.html.Google Scholar
8Liu, C.Y., Chen, C., Liao, C.N. and Tu, K.N.: Microstructure-electromigration correlation in a thin strips of eutectic SnPb solder stressed between Cu electrodes. Appl. Phys. Lett. 75, 58 (1999).CrossRefGoogle Scholar
9Huntington, H.B. Electromigration in metals, in Diffusion in Solids: Recent Developments, edited by Nowick, A.S. and Burton, J.J. (Academic Press, New York, 1979), pp. 303–352.Google Scholar
10Gangulee, A. and d’Heurle, F.M.: Anomalous large grains in alloyed aluminum thin films ΙΙ. Electromigration and diffusion in thin films with very large grains. Thin Solid Films 16(2), 227 (1973).CrossRefGoogle Scholar
11Blech, I.A. and Herring, C.: Stress generation by electromigration. Appl. Phys. Lett. 29, 131 (1976).CrossRefGoogle Scholar
12Lee, K.L., Hu, C.K. and Tu, K.N.: In situ scanning electron microscope comparison studies on electromigration of Cu and Cu(Sn) alloys for advanced chip interconnects. J. Appl. Phys. 78, 4428 (1995).CrossRefGoogle Scholar
13Yeh, E.C.C. and Tu, K.N.: Effects of contact resistance and film thickness on current crowding and the critical product of electromigration in Blech structures. J. Appl. Phys. 89, 3203 (2001).CrossRefGoogle Scholar
14Yeh, E.C.C. and Tu, K.N.: Mean-time-to-failure study of flip chip solder joints on Cu/Ni(V)/Al thin-film under-bump-metallization. J. Appl. Phys. 94, 5665 (2003).Google Scholar
15 Solder Data Sheet (Welco Castings, Hamilton, Ontario, Canada).Google Scholar
16Lu, C.C., Wang, S.J. and Liu, C.Y.: Electromigration Studies on Sn(Cu) Alloy Lines. J. Electron. Mater. 32 1515.Google Scholar