Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-23T02:33:11.575Z Has data issue: false hasContentIssue false
  • English
  • Français

Electrochemical, hydrothermal, and electrochemical-hydrothermal synthesis of barium titanate thin films on titanium substrates

Published online by Cambridge University Press:  31 January 2011

R. Bacsa ,
P. Ravindranathan  and
J.P. Dougherty
R. Bacsa
Affiliation:
Center for Dielectric Studies, Materials Research Laboratory, The Pennsylvania State University, University Park, Pennsylvania 16802
P. Ravindranathan
Affiliation:
Center for Dielectric Studies, Materials Research Laboratory, The Pennsylvania State University, University Park, Pennsylvania 16802
J.P. Dougherty
Affiliation:
Center for Dielectric Studies, Materials Research Laboratory, The Pennsylvania State University, University Park, Pennsylvania 16802
Get access

Abstract

Well-crystallized polycrystalline films of cubic BaTiO3 have been synthesized on Ti metal substrates by electrochemical, hydrothermal, and electrochemical-hydrothermal reaction of a Ti metal with a saturated solution of Ba(OH)2 in the temperature range 80 °C−200 °C. The films can be produced in the electrochemical process by the anodization of a Ti substrate in Ba(OH)2 solution at pH = 13 and current densities of the order of 10–50 mA/cm2. The films can also be synthesized by the hydrothermal reaction of Ba(OH)2 and a Ti substrate without electrical bias. A combination of these two techniques reduces the reaction time to 30–45 min. The films were found to have good adherence on the substrate and films of thickness up to 2 μm could be formed within a reaction time of 45 min. Capacitance measurements have yielded a dielectric constant of 300. The films prepared by the three different techniques have been compared for crystallinity and microstructure. The thickness of the films increased with temperature and time of reaction. The crystallinity decreased with extended time of reaction for a given temperature. It is likely that a reactive intermediate such as Ti(OH)4 (aq.) is formed in all the three cases which leads to the formation of crystalline BaTiO3.

Type
Articles
Information
Journal of Materials Research , Volume 7 , Issue 2 , February 1992 , pp. 423 - 428
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Shintani, Y. and Tada, O., J. Appl. Phys. 41, 2376 (1970).CrossRefGoogle Scholar
2.Putner, T., Thin Solid Films 1, 165 (1967).CrossRefGoogle Scholar
3.Vu, R., Dat, Huy, and Baumberger, C., Phys. Status Solidi 22, k67–k70 (1967).Google Scholar
4.Panitz, J. K. G. and Hu, C. C., Ferroelectrics 27, 161 (1980).CrossRefGoogle Scholar
5.Feldman, C., Rev. Sci. Instrum. 26, 463 (1955).CrossRefGoogle Scholar
6.Tomashpolskii, Yu Ya and Sevostyanov, M. A., Sov. Phys. Solid State 14, 2319 (1973).Google Scholar
7.Xu, J. J., Shaikh, A. S., and Vest, R. W., IEEE Trans. Ultrasonics, Ferroelectrics and Frequency Control 36 (1989).Google Scholar
8.Dosch, R. G., in Better Ceramics through Chemistry, edited by Brinker, C. J., Clark, D. E., and Ulrich, D. R. (Mater. Res. Soc. Symp. Proc. 32, Pittsburgh, PA, 1984), p. 157.Google Scholar
9.Switzer, J. A., Ceram. Bull. 66, 1521 (1987).Google Scholar
10.Matsumoto, Y., Sasaki, T., and Hombo, J., J. Electrochem. Soc. 138, 1259 (1991).CrossRefGoogle Scholar
11.Yoshimura, M., Yoo, S., Hayashi, M., and Ishizawa, N., Jpn. J. Appl. Phys. 28, L2007 (1990).CrossRefGoogle Scholar
12.Yoo, S. E., Hayashi, M., Ishizawa, N., and Yoshimura, M., J. Am. Ceram. Soc. 73, 2561 (1990).CrossRefGoogle Scholar
13.Kajiyoshi, K., Ishizawa, N., and Yoshimura, M., J. Am. Ceram. Soc. 74, 369 (1991).CrossRefGoogle Scholar
14.Ishizawa, N., Banno, H., Hayashi, M., Yoo, S. E., and Yoshimura, M., Jpn. J. Appl. Phys. 29, 2467 (1990).Google Scholar
15.Hayashi, M., Ishizawa, N., Yoo, S. E., and Yoshimura, M., J. Ceram. Soc. Jpn. 98, 930 (1990).CrossRefGoogle Scholar
16.Kutty, T. R. N. and Murugaraj, P., J. Mater. Sci. Lett. 7, 601 (1988).CrossRefGoogle Scholar
17.Osseo-Asare, K., Arriagada, F. J., and Adair, J. H., Cer. Trans., Ceramic Powder Sci. II, edited by Messing, G. L., Fuller, E. R. Jr, and Hausner, H. (The American Ceramic Society, Westerville, OH, 1988), pp. 47, 53.Google Scholar
18.Sibert, M. E., J. Electrochem. Soc. 110, 65 (1963).CrossRefGoogle Scholar