Hostname: page-component-cd9895bd7-8ctnn Total loading time: 0 Render date: 2024-12-24T03:03:30.172Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of annealing temperature on stress corrosion susceptibility of AA5083–H15 alloys

Published online by Cambridge University Press:  27 April 2016

Chun-Hung Yen ,
Chih-Ting Wu ,
Yen-Hao Chen  and
Sheng-Long Lee
Chun-Hung Yen
Affiliation:
Department of Mechanical Engineering, National Central University, Jhongli 320, Taiwan
Chih-Ting Wu
Affiliation:
Department of Vehicle Engineering, Army Academy R.O.C., Jhongli 320, Taiwan
Yen-Hao Chen
Affiliation:
Department of Mechanical Engineering, National Central University, Jhongli 320, Taiwan
Sheng-Long Lee*
Affiliation:
Department of Mechanical Engineering, National Central University, Jhongli 320, Taiwan
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Effects of annealing temperature on stress corrosion susceptibility of AA5083–H15 alloys were studied by annealing specimens at 150, 200, 250, 300, and 350 °C before sensitization. Nitric acid mass loss testing and slow strain rate testing were conducted to investigate intergranular corrosion (IGC) and stress corrosion cracking (SCC). Results indicate that H15 alloy was less susceptible to IGC, but this alloy had the highest susceptibility to IGC and SCC after sensitization. Due to the continuous precipitation of β phase, the sensitized 150 and 200 °C alloys were highly susceptible to IGC and SCC. The 250 °C alloy was less susceptible to IGC because of the absence of the precipitation of β phase. After sensitization, this alloy was also less susceptible to IGC and SCC on account of the discontinuous precipitation of β phase. The sensitized 300 and 350 °C alloys were susceptible to IGC but less susceptible to SCC because of their lower strength and higher elongation.

Keywords

annealingAlcorrosion
Type
Articles
Information
Journal of Materials Research , Volume 31 , Issue 8 , 28 April 2016 , pp. 1163 - 1170
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Charit, I. and Mishra, R.S.: Evaluation of microstructure and superplasticity in friction stir processed 5083 Al alloy. J. Mater. Res. 19, 3329 (2004).CrossRefGoogle Scholar
Zou, B., Chen, Z.Q., Liu, C.H., and Chen, J.H.: Microstructure evolution of heavily deformed AA5083 Al–Mg alloy studied by positron annihilation spectroscopy. Appl. Surf. Sci. 296, 154 (2014).Google Scholar
Davis, J. R. and Associates: ASM Specialty Handbook: Aluminum and Aluminum Alloys (ASM International, Materials Park, Ohio, 1994).Google Scholar
Bovard, F.S.: Sensitization and Environmental Cracking of 5xxx Aluminum Marine Sheet and Plate Alloys in Corrosion in Marine and Saltwater Environments II. Vol. 2004–14, Shifler, D.A., Tsuru, T., Natishan, P.M., and Ito, S. eds.; The Electrochemical Society proceedings: Pennington, New Jersey, 2005.Google Scholar
Searles, J.L., Gouma, P.I., and Buchheit, R.G.: Stress corrosion cracking of sensitized AA5083 (Al–4.5Mg–1.0Mn). Metall. Mater. Trans. A 32, 2859 (2001).Google Scholar
Kannan, M. B. and Raja, V.S.: Enhancing stress corrosion cracking resistance in Al–Zn–Mg–Cu–Zr alloy through inhibiting recrystallization. Eng. Fract. Mech. 77, 249 (2010).CrossRefGoogle Scholar
Popovic, M. and Romhanji, E.: Characterization of microstructural changes in an Al–6.8 wt% Mg alloy by electrical resistivity measurements. Mater. Sci. Eng. A 492, 460 (2008).Google Scholar
Jones, D.A.: Principles and Prevention of Corrosion (Prentice Hall International, Inc., New Jersey, 1996).Google Scholar
Meyers, M.A. and Chawla, K.K.: Mechanical Behavior of Materials (Cambridge University Press, New York, 2009).Google Scholar
Wei, R.P. and Gangloff, R.P.: Environmentally Assisted Crack Growth in Structural Alloys: Perspectives and New Directions (ASTM, Philadelphia, 1989).Google Scholar
Speidel, M.O.: Stress corrosion cracking of aluminum alloys. Metall. Trans. A 6A, 631 (1975).CrossRefGoogle Scholar
Bulloch, J.H.: Some effects of yield strength on the stress corrosion cracking behaviour of low alloy steels in aqueous environments at ambient temperatures. Eng. Fail. Anal. 11, 843 (2004).Google Scholar
Sarıoğlu, F.: The effect of tempering on susceptibility to stress corrosion cracking of AISI 4140 steel in 33% sodium hydroxide at 80 °C. Mater. Sci. Eng. A 315, 98 (2001).Google Scholar
Savoie, M., Esnouf, C., Fournier, L., and Delafosse, D.: Influence of ageing heat treatment on alloy A-286 microstructure and stress corrosion cracking behavior in PWR primary water. J. Nucl. Mater. 360, 222 (2007).Google Scholar
Humphreys, F.J.: Recrystallization and Related Annealing Phenomena (Elsevier, Amsterdam, Boston, 2004).Google Scholar
Goswamia, R., Spanosa, G., Paoa, P.S., and Holtza, R.L.: Precipitation behavior of the β phase in Al-5083. Mater. Sci. Eng. A 527, 1089 (2010).Google Scholar
Callister, W.D.: Materials Science and Engineering: An Introduction, 7th ed. (John Wiley & Sons, New York, 2007).Google Scholar