Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-17T15:12:20.771Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of quenching and partitioning process to low-alloy wear resistant steel

Published online by Cambridge University Press:  11 March 2016

Wenqian Zhou ,
Yufu Sun ,
Qianqian Wang  and
Liping Ding
Wenqian Zhou
Affiliation:
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450002, Henan, China
Yufu Sun*
Affiliation:
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450002, Henan, China
Qianqian Wang
Affiliation:
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450002, Henan, China
Liping Ding
Affiliation:
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450002, Henan, China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

To find the optimal Quenching and Partitioning (Q&P) process parameters of low-alloy wear resistant steel, various Q&P processes including quenching temperature, partitioning temperature and partitioning time were designed and tested by using orthogonal experiment method. Through analysis of orthogonal experiment, quenching temperature was the most important influential factor on the impact toughness and hardness, and partitioning time played a critical role on tensile strength. The optimal Q&P heat treatment parameters of low alloy wear resistant steel were partitioning at 350 °C for 10 min immediately after quenching at 100 °C. The microstructure of samples was composed of martensite laths and retained austenite. The relative volume fraction of retained austenite increased with the increase of quenching temperature and decreased gradually with the lengthening of partitioning time. Combining the results of Energy dispersive spectrometer, the reason for decrease of retained austenite was the existence of carbide precipitation and the carbide was (Fe, Cr)3C7. Compared to the traditional heat treatment of quenching and low temperature tempering, the samples under Q&P treatment displayed higher toughness and maintained relatively high tensile strength and wear resistance.

Keywords

strengthtoughnesshardness
Type
Articles
Information
Journal of Materials Research , Volume 31 , Issue 5 , 14 March 2016 , pp. 663 - 669
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Lyu, Y., Zhu, Y., and Olofsson, U.: Wear between wheel and rail: A pin-on-disc study of environmental conditions and iron oxides. Wear 328–329, 227–285 (2015).Google Scholar
Pan, Y-N., Chang, W-S., and Chang, R-M.: Optimal heat treatment conditions and properties of bimetal (high Cr cast iron alloyed steel) hammers. Int. J. Cast Met. Res. 21, 71–75 (2008).CrossRefGoogle Scholar
Tao, X., Xiaoman, L., and Cuiyan, Y.: Influence of rare earth on wear resistance of wear resistant cast iron containing low alloy. J. Rare Earths 22, 139–142 (2004).Google Scholar
Matas, S. and Hehemann, R.F.: Retained austenite and the tempering of martensite. Nature 87, 685–686 (1960).Google Scholar
Wang, X.D., Zhong, N., Rong, Y.H., and Xu, Z.Y.: Novel ultrahigh-strength nanolath martensitic steel by quenching-partitioning-tempering process. J. Mater. Res. 24, 260–267 (2009).CrossRefGoogle Scholar
Speer, J., Matlock, D.K., De Cooman, B.C., and Schroth, J.G.: Carbon partitioning into austenite after martensite transformation. Acta Mater. 51, 2611–2622 (2003).CrossRefGoogle Scholar
Misra, R.D.K., Zheng, H., Wu, K.M., and Karjalainen, L.P.: Niobium-containing quenching and partitioning processed ultrahigh strength martensite–austenite dual phase steels. Mater. Sci. Eng., A 579, 188–193 (2013).Google Scholar
Rao, B.V. and Thomas, G.: Transmission electron microscopy characterization of dislocated “lath” martensite. In Proceedings of the International Conference on Martensitic Transformations-79 (MIT: Boston, 1979); pp. 12–16.Google Scholar
Sarikaya, M. and Thomas, G.: Lath martensites in carbon steels are they bainitic. In Proceedings of an International Conference on Solid to Solid Phase Transformations (TMS-AIME: Cambridge, 1982); pp. 999–1004.Google Scholar
Zuyao, X. and Xuemin, L.: Diffusion of carbon during the formation of low-carbon martensite. Scr. Mater. 17, 1285–1288 (1983).Google Scholar
Speer, J.G., Edmonds, D.V., Rizzo, F.C., and Matlock, D.K.: Partitioning of carbon from supersaturated plates of ferrite, with application to steel processing and fundamentals of the bainite transformation. Curr. Opin. Solid State Mater. Sci. 8, 219–237 (2004).CrossRefGoogle Scholar
Edmonds, D.V., He, K., Rizzo, E.C., De Cooman, B.C., Matlock, D.K., and Speer, J.: Quenching and partitioning martensite–A novel steel heat treatment. Mater. Sci. Eng., A 438, 25–34 (2006).CrossRefGoogle Scholar
Chatterjee, S., Wang, H.-S., Yang, J.R., and Bhadeshia, H.K.D.H.: Mechanical stabilisation of austenite. Mater. Sci. Technol. 22, 645 (2006).Google Scholar
Lee, C.G., Kim, S.J., Kim, T.H., and Lee, S.: Effects of volume fraction and stability of retained austenite on formability in a 0.1C–1.5Si–1.5Mn–0.5Cu TRIP-aided cold-rolled steel sheet. Mater. Sci. Eng., A 371, 16 (2004).CrossRefGoogle Scholar
Zhang, K., Zhang, M., Guo, Z., Chen, N., and Rong, Y.: A new effect of retained austenite on ductility enhancement in high-strength quenching–partitioning–tempering martensitic steel. Mater. Sci. Eng., A 528, 8486–8491 (2011).Google Scholar
Zhong, N., Wang, X.D., Wang, L., and Rong, Y.H.: Enhancement of the mechanical properties of a Nb-microalloyed advanced high-strength steel treated by quenching–partitioning–tempering process. Mater. Sci. Eng., A 506, 111–116 (2009).Google Scholar
Xu, L., Yan, Z., Liu, Y., and Li, H.: Microstructure evolution and martensitic transformation behaviors of 9Cr–1.8W–0.3Mo ferritic heat-resistant steel during quenching and partitioning treatment. J. Mater. Res. 28, 2835–2843 (2013).Google Scholar
Mola, J. and De Cooman, B.C.: Quenching and partitioning (Q&P) processing of martensitic stainless steels. Metall. Mater. Trans. A 44, 946–967 (2013).Google Scholar
Maheswari, N., Ghosh Chowdhury, S., Hari Kumar, K.C., and Sankaran, S.: Influence of alloying elements on the microstructure evolution and mechanical properties in quenched and partitioned steels. Mater. Sci. Eng., A 600, 12–20 (2014).Google Scholar
GB/T 228.1-2010: Metallic Materials-Tensile Testing at Ambient Temperature (China Standard Press, Beijing, 2011).Google Scholar
GB/T 229-2007: Metallic Materials-Charpy Pendulum Impact Test Method (China Standard Press, Beijing, 2007).Google Scholar
GB/T 230.1-2009: Metallic Materials-Rockwell Hardness Test-Part 1: Test Method (China Standard Press, Beijing, 2009).Google Scholar
Zhao, L., Van Dijk, N.H., Brück, E., Sietsma, J., and Van der Zwaag, S.: Magnetic and X-ray diffraction measurements for the determination of retained austenite in TRIP steel. Mater. Sci. Eng., A 313, 145–152 (2001).Google Scholar
GB/T 12444-2006: Metallic Materials-Wear Test Method-Block-on-Ring Sliding Wear Test (China Standard Press, Beijing, 2006).Google Scholar
Krauss, G.: Steel: Heat Treatment and Processing Principles (ASM International Metals Park, OH, USA, 1990).Google Scholar
Nayak, S.S., Anumolu, R., Misra, R.D.K., Kim, K.H., and Lee, D.L.: Microstructure–hardness relationship in quenched and partitioned medium-carbon and high-carbon steels containing silicon. Mater. Sci. Eng., A 8, 442–456 (2008).Google Scholar