Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-23T02:41:00.886Z Has data issue: false hasContentIssue false
  • English
  • Français

Dynamic consolidation of superhard materials

Published online by Cambridge University Press:  31 January 2011

Wenbo Yang ,
G.M. Bond ,
Hua Tan ,
Thomas J. Ahrens  and
G. Liu
Wenbo Yang
Affiliation:
Lindhurst Laboratory of Experimental Geophysics, Seismological Laboratory, California Institute of Technology, Pasadena, California 91125
G.M. Bond
Affiliation:
Department of Materials and Metallurgical Engineering, New Mexico Institute of Mining and Technology, Socorro, New Mexico 87801
Hua Tan
Affiliation:
Beijing Institute of Technology, P. O. Box 327, Beijing, People's Republic of China
Thomas J. Ahrens
Affiliation:
Lindhurst Laboratory of Experimental Geophysics, Seismological Laboratory, California Institute of Technology, Pasadena, California 91125
G. Liu
Affiliation:
Department of Materials and Metallurgical Engineering, New Mexico Institute of Mining and Technology, Socorro, New Mexico 87801
Get access

Abstract

Shock consolidation experiments were conducted via flyer impact on synthetic diamond (6–12 μm) and cubic boron nitride (c-BN) (4–8 μm) admixed with SiC whisker (SCW), Si3N4 whisker (SNW), SiC powder, and Si powder contained in stainless steel capsules under the shock pressure range of 10–30 GPa. Scanning electron microscopy and transmission electron microscopy imaging of the samples revealed no plastic deformation or melting of diamond and virtually no deformation of c-BN, whereas the SCW and SNW were extensively melted and recrystallized into bundle-shaped crystallites. In contrast, SiC powder mixed with diamond was also melted but demonstrated equant grain growth. A new method to calculate the shock temperature and melt fraction is formulated on the basis of Milewski's sphere-rod packing data. The new method assigns excess bulk volume to the zone around whiskers and yields a better description of the energy deposition mechanism of the consolidation of powder-whisker systems. Some of the experiments employed Sawaoka's post-shock annealing technique, in which the sample is sandwiched between two layers of a mixture of titanium powder plus carbon. Very well consolidated samples were obtained with post-shock heating under shock pressures of only about 11 GPa. Micro-Vickers hardness values up to 27 GPa were obtained for c-BN plus SCW at a low impact velocity of 1.45 km/s with post-shock heating. This hardness is similar to that obtained at a higher impact velocity of 1.95 km/s without post-shock heating. To understand the post-shock heating process, one-dimensional time dependent temperature profile calculations were conducted for the sample and Ti + C layers. Post-shock heating appears to be very important in the consolidation of powder and whisker admixture. The calculated optimum Ti + C thickness is about 0.8–1.7 mm at a porosity of 40% for a typical sample thickness of 2 mm. The heating and cooling time is a few milliseconds. Good compacts with micro-Vickers hardness values up to 28 GPa were also obtained upon shock consolidation of diamond plus Si admixtures.

Type
Articles
Information
Journal of Materials Research , Volume 7 , Issue 6 , June 1992 , pp. 1501 - 1518
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Potter, D. K. and Ahrens, T. J., Appl. Phys. Lett. 51, 317–319 (1987).CrossRefGoogle Scholar
2.Bundy, F. P. and Wentorf, R. H., J. Chem. Phys. 38, 1144–1149 (1963).CrossRefGoogle Scholar
3.Akashi, T., Lotrich, V., Sawaoka, A., and Beauchamp, E. K., J. Am. Ceram. Soc. 68, c–322 (1985).CrossRefGoogle Scholar
4.Ahrens, T. J. and Potter, D. K., in Shock Waves in Condensed Matter-1987, edited by Schmidt, S. C. and Holmes, N. C. (North-Holland Physics Publishing, Amsterdam, The Netherlands, 1988), pp. 419–422.Google Scholar
5.Sawai, S. and Kondo, K., J. Am. Ceram. Soc. 71, c–185 (1988).CrossRefGoogle Scholar
6.Akashi, T. and Sawaoka, A. B., J. Mater. Sci. 22, 1127–1134 (1987).CrossRefGoogle Scholar
7.Tan, H. and Ahrens, T. J., J. Mater. Res. 3, 1010–1020 (1988).CrossRefGoogle Scholar
8.Sawaoka, A. and Akashi, T., in Shock Waves in Condensed Matter-1987, edited by Schmidt, S. C. and Holmes, N. C. (North-Holland Physics Publishing, Amsterdam, The Netherlands, 1988), pp. 423–425.Google Scholar
9.JANAF Thermodynamical Tables, edited by Chase, M. W., Jr., Davies, C. A., Downey, J. R., Jr., Frurip, D. J., McDonald, R. A., and Syverud, A. N. (American Chemical Society and the American Institute of Physics for the National Bureau of Standards, 1985), pp. 1563, 634.Google Scholar
10.Gray, G. T., Metall. Trans. 20A, June, 1989.Google Scholar
11.LASL Shock Hugoniot Data, edited by Marsh, S. P. (University of California, Berkeley, CA, 1980), pp. 328, 249.Google Scholar
12.Heine, R. W., Loper, C. R., Jr., and Rosenthal, P. C., Principles of Metal Casting (McGraw-Hill Book Company, New York, 1967), pp. 178–209.Google Scholar
13.Handbook of Fillers and Reinforcements for Plastics, edited by Katz, Harry S. and Milewski, John V. (Van Nostrand Reinhold Company, New York, 1978), p. 66.Google Scholar
14.Pavlovskii, M. N., Sov. Phys. Solid State 13, 741–742 (1971).Google Scholar
15. Tateho Chemical Industries Co., Ltd., technical data, 1988.Google Scholar
16.Soma, T., Sawaoka, A., and Saito, S., in Proc. Fourth Int. Conf. on High Pressure-1974, Special Issue of the Rev. of Phys. Chem. Jpn., edited by Osugi, J. (Kawakita, Kyoto, Japan, 1975), pp. 446–453.Google Scholar
17.Lange's Handbook of Chemistry, edited by Dean, J. A. (McGraw-Hill, Inc., New York, 1985), p. 3–2, 9–63, 9–137, 4–123.Google Scholar
18.Knittle, E., Wentzcovitch, R. M., Jeanloz, R., and Cohen, M. L., Nature 337, 349–352 (1989).CrossRefGoogle Scholar
19.Van Vechten, J. A., Phys. Rev. B 7, 1479–1507 (1973).CrossRefGoogle Scholar
20.Kinslow, R., High Velocity Impact Phenomena (Academic Press, Inc., New York, 1970), p. 549, 551, 374.Google Scholar
21. Derived from Mashimo's, T. data in Shock Waves in Condensed Matter-1987, edited by Schmidt, S. C. and Holmes, N. C. (North-Holland Physics Publishing, Amsterdam, The Netherlands, 1988), pp. 289–292.Google Scholar
22.Boslough, M. B., A Thermodynamical Model for Shock-Induced Chemical Reactions in Porous Solids: Analogs and Contrasts to Detonation, in Proc. 9th Symp. (Int.) on Detonation-1989.Google Scholar
23.Hill, J. M. and Dewynne, J. N., Heat Conduction (Blackwell Scientific Publications, 1987), p. 197.Google Scholar
24.Lienhard, J. H., A Heat Transfer Text Book (Prentice-Hall, Inc., Englewood Cliffs, NJ, 1981), p. 492.Google Scholar
25.Schwarzkopf, P. and Kieffer, R., Cemented Carbides (The Macmillan Company, New York, 1960), p. 67.Google Scholar
26.Ahrens, T. J., in Methods of Experimental Physics (Academic Press, New York, 1987), Vol. 24, Part A, pp. 185–234.Google Scholar
27.Ahrens, T. J., Kostka, D., Kasiraj, P., and Vreeland, T., Jr., in Rapid Solidification Processing Principles and Technologies, III, Proc. 3rd Conf. on Rapid Solidification Processing, edited by Mehrabian, R. (U.S. National Bureau of Standards, Gaithersburg, MD, 1982), pp. 672–677.Google Scholar
28.Gourdin, W. H., J. Appl. Phys. 55, 172–181 (1984).CrossRefGoogle Scholar
29.Schwarz, R. B., Kasiraj, P., Vreeland, T., Jr., and Ahrens, T. J., Acta Metall. 32, 1243 (1984).CrossRefGoogle Scholar
30.Robie, R. A., Hemingway, B. S., and Fisher, J. R., Thermodynamic Properties of Minerals and Related Substances at 298.15 K and 1 bar (105 pascals) Pressure and at Higher Temperatures (Geological Survey Bulletin 1452, 1978), p. 41.Google Scholar
31. John Milewski, V., A Study of the Packing of Fibers and Spheres, Ph.D. Thesis, Rutgers University (1973).Google Scholar
32.Kumar, P. and Clifton, R. J., J. Appl. Phys. 48, 4850 (1977).CrossRefGoogle Scholar
33.Rabie, R. L., Vorthman, J. E., and Dienes, J. K., Shock Waves in Condensed Matter-1983, edited by JAsay, R., Graham, R. A., and Straub, G. K. (Elsevier Science Publisher B. V., 1984), pp. 199–202.Google Scholar
34.Mutz, A. and Vreeland, T., Jr., Several Techniques for One-Dimensional Strain Consolidation of Multiple Cavities, in Proc. Int. Conf. On High Strain Phenomena in Materials, edited by Murr, L. E., Meyers, M., and Staudhammer, K. P. (1991).Google Scholar