Hostname: page-component-7bb8b95d7b-nptnm Total loading time: 0 Render date: 2024-09-12T14:35:17.584Z Has data issue: false hasContentIssue false
  • English
  • Français

Determination of shear viscosity of borosilicate glass + silica powder compacts by an optical system

Published online by Cambridge University Press:  31 January 2011

Jaecheol Bang ,
Guo-Quan Lu  and
Jesus Noel Calata
Jaecheol Bang
Affiliation:
Department of Materials Science and Engineering, Virginia Polytechnic Institute and State University, Blacksburg, Virginia 24061
Guo-Quan Lu
Affiliation:
Department of Materials Science and Engineering, Virginia Polytechnic Institute and State University, Blacksburg, Virginia 24061
Jesus Noel Calata
Affiliation:
Department of Materials Science and Engineering, Virginia Polytechnic Institute and State University, Blacksburg, Virginia 24061
Get access

Abstract

The shear viscosity of borosilicate glass (BSG) + silica powder compacts was determined during isothermal sintering at temperatures between 665 and 715°C. An optical system was used to measure in situ the densification profiles of the compacts in the form of thick films constrained on a rigid substrate and in-plane stresses generated during sintering. The shear viscosity as a function of relative density was calculated from these measurements by using Scherer's viscous constitutive equations for a porous sintering body. The shear viscosity for samples with silica contents from 0 to 20 vol% generally showed a slow increase with density in the low-density regime followed by a rapid rise after some threshold density that decreased with either increasing silica powder content or decreasing sintering temperature. The dependence of shear viscosity on relative density is consistent with results from sinter-forging experiments. However, results obtained from pure BSG compacts also revealed strong dependence of shear viscosity on temperature and microstructure, which has been all but neglected in previous theoretical studies.

Type
Articles
Information
Journal of Materials Research , Volume 14 , Issue 3 , March 1999 , pp. 1062 - 1068
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Rahaman, M.N., De Jonghe, L. C., and Brook, R.J., J. Am. Ceram. Soc. 69 (1), 53–58 (1986).CrossRefGoogle Scholar
2.Venkatachari, K.R. and Raj, R., J. Am. Ceram. Soc. 69 (6), 499–506 (1986).CrossRefGoogle Scholar
3.Rahaman, M.N., De Jonghe, L. C., Scherer, G.W., and Brook, R.J., J. Am. Ceram. Soc. 70 (10), 766–774 (1987).CrossRefGoogle Scholar
4.Bordia, R.K. and Raj, R., J. Am. Ceram. Soc. 71 (4), 302–310 (1988).CrossRefGoogle Scholar
5.Ducamp, V.C. and Raj, R., J. Am. Ceram. Soc. 72 (5), 798–804 (1989).CrossRefGoogle Scholar
6.Sura, V.M. and Panda, P. C., J. Am. Ceram. Soc. 73 (4), 2697–2701 (1988).CrossRefGoogle Scholar
7.Dutton, R.E. and Rahaman, M.N., J. Am. Ceram. Soc. 75 (8), 2146–2154 (1992).CrossRefGoogle Scholar
8.Scherer, G.W., J. Non-Cryst. Solids 34, 239–256 (1979).CrossRefGoogle Scholar
9.Bordia, R.K. and Scherer, G. W., Acta Metall. 36, 2393–2397 (1988).CrossRefGoogle Scholar
10.Lu, G-Q., Sutterlin, R. C., and Gupta, T. K., J. Am. Ceram. Soc. 76 (8), 1907–1914 (1993).CrossRefGoogle Scholar
11.Bang, J. and Lu, G-Q., J. Mater. Res. 10, 1321–1326 (1995).CrossRefGoogle Scholar
12.Bang, J. and Lu, G-Q., J. Am. Ceram. Soc. 78 (3), 813–815 (1995).CrossRefGoogle Scholar
13.Scherer, G.W., Mechanics of Granular Materials and Powder Systems (ASME, New York, 1992), Vol. 37, pp. 1–18.Google Scholar
14.Jagota, A., Mikeska, K. R., and Bordia, R. K., J. Am. Ceram. Soc. 73 (8), 2266–2273 (1990).CrossRefGoogle Scholar