Hostname: page-component-586b7cd67f-tf8b9 Total loading time: 0 Render date: 2024-11-23T14:11:27.585Z Has data issue: false hasContentIssue false

Creep property measurement of service-exposed SUS 316 austenitic stainless steel by the small-punch creep-testing technique

Published online by Cambridge University Press:  31 January 2011

Maribel L. Saucedo-Muñoz*
Affiliation:
Fracture Research Institute, Faculty of Engineering, Tohoku University, Sendai 980–8579, Japan and Instituto Politecnico Nacional, ESIQIE, Apartado Postal 75–556, Mexico, D.F., 07300
Shin-Ichi Komazaki
Affiliation:
Materials Science and Engineering, Muroran Institute of Technology, 27–1 Mizumotocho, Muroran, Hokkaido 050–8585, Japan
Toru Takahashi
Affiliation:
Fracture Research Institute, Faculty of Engineering, Tohoku University, Sendai 980–8579, Japan
Toshiyuki Hashida
Affiliation:
Fracture Research Institute, Faculty of Engineering, Tohoku University, Sendai 980–8579, Japan
Tetsuo Shoji
Affiliation:
Fracture Research Institute, Faculty of Engineering, Tohoku University, Sendai 980–8579, Japan
*
a)Address all correspondence to this author.[email protected]
Get access

Abstract

The creep properties for SUS 316 HTB austenitic stainless steel were evaluated by using the small-punch creep test at 650 °C for loads of 234, 286, 338, 408, and 478 N and at 700 °C for loads of 199 and 234 N. The creep curves, determined by means of the small-punch creep test, were similar to those obtained from a conventional uniaxial creep test. That is, they exhibited clearly the three creep stages. The width of secondary creep stage and rupture time tr decreased with the increase in testing load level. The creep rupture strength for the service-exposed material was lower than that of the as-received material at high testing loads. However, the creep resistance behavior was opposite at relatively low load levels. This difference in creep resistance was explained on the basis of the difference in the creep deformation and microstructural evolution during tests. It was also found that the ratio between the load of small-punch creep test and the stress of uniaxial creep test was about 1 for having the same value of creep rupture life.

Type
Articles
Copyright
Copyright © Materials Research Society 2002

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Leslie, W.C.,The Physical Metallurgy of Steels (McGraw Hill, New York, 1982), p. 326.Google Scholar
2.Marshal, P.,Austenitic Stainless Steels Microstructure and Properties (Elsevier Applied Science Publisher, London, United Kingdom, 1984), pp. 94, 264.Google Scholar
3.Viswanathan, R.,Damage Mechanism and Life Assessment of High-Temperature Components (ASM International, Metals Park, OH, 1989), p. 59.CrossRefGoogle Scholar
4.Saucedo-Muñoz, M.L., Matsushita, T., Hashida, T., Shoji, T., and Takahashi, H., J. Test. Eval. 28, 352 (2000).CrossRefGoogle Scholar
5.Kwon, H., Cheng, S., Saucedo, M.L., Hashida, T., and Takahashi, H.,Trans. JSME 63A, 61 (1997).CrossRefGoogle Scholar
6.Komazaki, S., Hashida, T., Shoji, T., and Suzuki, K., J. Test. Eval. 28, 249 (2000).CrossRefGoogle Scholar
7.Parker, J.D. and James, J.D., ASME 279, 167 (1994).Google Scholar
8.Saito, Y., A Study of Fracture in SUS 316 H Steel Boiler Pipes Exposed at High Temperatures for Prolonged Times by Electro-chemical Methods, Ph.D. Thesis, Tohoku University, Sendai, Japan (1999), p. 51.Google Scholar
9.National Research Institute for Metals, Creep Data Sheet (NRIM,No. 6A, Tokyo, Japan, 1978), pp. 112.Google Scholar
10.ASM Metals Handbook (ASM International, Metals Park, OH,1990), Vol. 8, p. 325.Google Scholar
11.Fujita, N., Nakazawa, T., Komatsu, H., Kaguchi, H., Kaneko, H., and Ueda, H., Tetsu to Hagane 82, 80 (1996).CrossRefGoogle Scholar
12.Tettamanti, S. and Crudeli, R., A Procedure for High Temperature Plant Components Life Evaluation: Small Punch Creep Test Methodology, inProceedings of an International Symposium on Case Histories on Integrity and Failure Industry, (Technical Research Center of Finland, Finland, 1999), pp. 895905.Google Scholar
13.Schey, J.A.,Tribology in Metalworking (ASM, Metals Park, OH, 1984), p. 491.Google Scholar