Hostname: page-component-78c5997874-lj6df Total loading time: 0 Render date: 2024-11-17T16:14:40.123Z Has data issue: false hasContentIssue false
  • English
  • Français

Comment on the determination of mechanical properties from the energy dissipated during indentation

Published online by Cambridge University Press:  03 March 2011

Jürgen Malzbender
Jürgen Malzbender*
Affiliation:
Forschungszentrum Jülich GmbH, Institute for Materials and Processes in Energy Systems, 52425 Jülich, Germany
*
a Address all correspondence to this author. email: [email protected]
Get access

Abstract

Based on a comparison of relationships between the energy dissipated during indentation and the ratio of hardness to elastic modulus, a procedure is outlined to determine hardness and elastic modulus from the ratio of the elastic to total energy dissipated during an indentation cycle for non-ideal indenters.

Keywords

Elastic propertiesHardnessIndentation
Type
Rapid Communications
Information
Journal of Materials Research , Volume 20 , Issue 5 , May 2005 , pp. 1090 - 1092
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Oliver, W.C. and Pharr, G.M.: An improvement technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
2.Oliver, W.C. and Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 (2004).CrossRefGoogle Scholar
3.Malzbender, J. and de With, G.: Indentation load-displacement curve, plastic deformation and energy. J. Mater. Res. 17, 502 (2002).CrossRefGoogle Scholar
4.Malzbender, J.: Comment on hardness definitions. J. Eur. Ceram. Soc. 23, 1355 (2003).CrossRefGoogle Scholar
5.Cheng, Y-T. and Cheng, C-M.: Relationships between hardness, elastic modulus, and the work of indentation. Appl. Phys. Lett. 73, 614 (1998).CrossRefGoogle Scholar
6.Cheng, Y-T. and Li, Z.: Scaling relationships for indentation measurements. Philos. Mag. A. 82, 1893 (2002).CrossRefGoogle Scholar
7.Thurn, J. and Cook, R.F.: Indentation-induced deformation at ultramicroscopic and macroscopic contacts. J. Mater. Res. 19, 124 (2004).Google Scholar
8.Ni, W., Cheng, Y-T., Cheng, C.M. and Grummon, D.S.: An energy-based method for analyzing instrumented spherical indentation experiments. J. Mater. Res. 19, 149 (2004).CrossRefGoogle Scholar
9.Malzbender, J.: The energy dissipated during spherical indentation. J. Mater. Res. 19, 1605 (2004).CrossRefGoogle Scholar
10.Choi, Y., Lee, H-S. and Kwon, D.: Analysis of sharp-tip-indentation load-depth curve for contact area determination taking into account pile-up and sink-in effects. J. Mater. Res. 19, 3307 (2004).CrossRefGoogle Scholar
11.Ma, D., Ong, C.W. and Wong, S.F.: New relationship between Young’s modulus and nonideally sharp parameters. J. Mater. Res. 19, 2144 (2004).Google Scholar
12.Dejun, M.A., Ong, C.W., Jianmin, L. and Jiawen, H.E.: Determination of Young’s modulus by nanoindentation. Sci. China Ser. E. Eng. Mater. Sci. 47, 398 (2004).Google Scholar
13.Marx, V. and Balke, H.: A critical investigation of the unloading behaviour of sharp indentation. Acta Mater. 45, 3791 (1997).Google Scholar
14.Venkatesh, T.A., van Vleit, K.J., Ginnakopoulos, A.E. and Suresh, S.: Determination of elasto-plastic properties by instrumented sharp indentation: Guidelines for property extraction. Scripta Mater. 42, 833 (2000).CrossRefGoogle Scholar
15.Dao, M., Chollacoop, N., van Vliet, K.J., Venkatesh, T.A. and Suresh, S.: Computational modeling of the forward and reverse problems in instrumented sharp indentation. Acta Mater. 49, 3899 (2001).CrossRefGoogle Scholar
16.Tabor, D.: Hardness of Metals (Oxford Univesity Press, Oxford, U.K., 1951).Google Scholar
17.Johnson, K.L.: Contact Mechanics (Cambridge University Press, London, U.K., 1985).CrossRefGoogle Scholar