Hostname: page-component-cd9895bd7-gxg78 Total loading time: 0 Render date: 2024-12-23T19:16:53.811Z Has data issue: false hasContentIssue false
  • English
  • Français

Application of a self-consistent model to study the flow behavior of CuZn39Pb3 at elevated temperatures

Published online by Cambridge University Press:  13 November 2015

A. Momeni
A. Momeni*
Affiliation:
Department of Materials Science and Engineering, Hamedan University of Technology, 6516913733 Hamedan, Iran
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Hot compression tests were carried out on the duplex α + β leaded brass CuZn39Pb3 in temperature range of 600–800 °C and at strain rates of 0.001–1 s−1. A self-consistent model was used to analyze the flow behavior of the constituents and the material. A linear viscoplastic model was used to relate the flow stress of β and α + β composite to strain rate and the corresponding viscosity parameters were calculated at various deformation conditions. Using the viscosity parameters of β and α + β and the volume fractions of the constituents, the viscosity parameter of α was calculated. The values of the viscosity-like parameters and strain rate sensitivity for β and α + β composite were calculated using the nonlinear powerlaw viscoplastic equation. The results showed that the flow stress of α calculated using the self-consistent model was considerably higher than that of β. The difference could be attributed to the lower Zn content in α. The flow stress of α + β composite was calculated using the law of mixture rule. The law of mixture modeling of α + β composite for the iso-strain condition resulted to the overestimation of flow stress. The difference between the experimental and predicted results was attribute to the strain partitioning between α and β.

Keywords

hot pressingCustress/strain relationshipbrassmodeling
Type
Articles
Information
Journal of Materials Research , Volume 30 , Issue 22 , 27 November 2015 , pp. 3453 - 3460
Copyright
Copyright © Materials Research Society 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Sharififar, M. and Akbari Mousavi, S.A.A.: Tensile deformation and fracture behavior of CuZn5 brass alloy at high temperature. Mater. Sci. Eng., A 594, 118 (2014).Google Scholar
Xiao, Y-H., Guo, C., and Guo, X-Y.: Constitutive modeling of hot deformation behavior of H62 brass. Mater. Sci. Eng., A 528, 6510 (2011).Google Scholar
Hatherly, M., Malin, A.S., Carmichael, C.M., Humphreys, F.J., and Hirsch, J.: Deformation processes in hot worked copper and α brass. Acta Metall. 34, 2247 (1986).CrossRefGoogle Scholar
Padmavardhani, D. and Prasad, Y.V.R.K.: Characterization of hot deformation behavior of brasses using processing maps: Part I, β brass and α-β brass. Metall. Trans. A 22, 2993 (1991).CrossRefGoogle Scholar
Momeni, A., Ebrahimi, G.R., and Faridi, H.: Effect of chemical composition and processing variables on the hot flow behavior of leaded brass alloys. Mater. Sci. Eng., A 626, 1 (2015).CrossRefGoogle Scholar
Blaz, L., Konior, Z., and Majda, T.: Structural aspects of α/β transformation in hot deformed CuZn-39Pb3 alloy. J. Mater. Sci. 36, 3629 (2001).CrossRefGoogle Scholar
Farnoush, H., Momeni, A., Dehghani, K., Mohandesi, J.A., and Keshmiri, H.: Hot deformation characteristics of 2205 duplex stainless steel based on the behavior of constituent phases. Mater. Des. 31, 220 (2010).Google Scholar
Momeni, A., Kazemi, S., and Bahrani, A.: Hot deformation behavior of microstructural constituents in a duplex stainless steel during high-temperature straining. Int. J. Miner., Metall. Mater. 20, 953 (2013).CrossRefGoogle Scholar
Babu, S.S., Livingston, J., and Lippold, J.C.: Physical simulation of deformation and microstructure evolution during friction stir processing of Ti-6Al-4V alloy. Metall. Mater. Trans. A 44, 3577 (2013).CrossRefGoogle Scholar
Sahebdel, L., Abbasi, S.M., and Momeni, A.: Microstructural evolution through hot working of the single-phase and two-phase Ti-6Al-4V alloy. Int. J. Mater. Res. 102, 41 (2011).Google Scholar
Lin, Y.C., Zhang, J., and Zhong, J.: Application of neural networks to predict the elevated temperature flow behavior of a low alloy steel. Comput. Mater. Sci. 43, 752 (2008).CrossRefGoogle Scholar
Shu, X., Lu, S., Wang, K., and Li, G.: A comparative study on constitutive equations and artificial neural network model to predict high-temperature deformation behavior in Nitinol 60 shape memory alloy. J. Mater. Res. 30, 1988 (2015).CrossRefGoogle Scholar
Momeni, A. and Dehghani, K.: Hot working behavior of 2205 austenite-ferrite duplex stainless steel characterized by constitutive equations and processing maps. Mater. Sci. Eng., A 528, 1448 (2011).CrossRefGoogle Scholar
Spigarelli, S., El Mehtedi, M., Ricci, P., and Mapelli, C.: Constitutive equations for prediction of the flow behavior of duplex stainless steels. Mater. Sci. Eng., A 527, 4218 (2010).Google Scholar
Kim, J.H., Yeom, J.T., Park, N.K., and Lee, C.S.: Constitutive analysis of the high-temperature deformation behavior of single phase α-Ti and α + β Ti-6Al-4V alloy. Mater. Sci. Forum 539–543, 3607 (2007).CrossRefGoogle Scholar
Fan, X.G. and Yang, H.: Internal-state-variable based self-consistent constitutive modeling for hot working of two-phase titanium alloys coupling microstructure evolution. Int. J. Plast. 27, 1833 (2011).Google Scholar
Kim, J.H., Semiatin, S.L., Lee, Y.H., and Lee, C.S.: A self-consistent approach for modeling the flow behavior of the alpha and beta phases in Ti-6Al-4V. Metall. Mater. Trans. A 42, 1805 (2011).Google Scholar
Momeni, A., Dehghani, K., and Poletti, M.C.: Law of mixture used to model the flow behavior of a duplex stainless steel at high temperatures. Mater. Chem. Phys. 139, 747 (2013).Google Scholar
Spigarelli, S., El Mehtedi, M., Cabibbo, M., Gabrielli, F., and Ciccarelli, D.: High temperature processing of brass: Constitutive analysis of hot working of Cu–Zn alloys. Mater. Sci. Eng., A 615, 331 (2014).CrossRefGoogle Scholar
Luo, J., Li, M., Li, X., and Shi, Y.: Constitutive model for high temperature deformation of titanium alloys using internal state variables. Mech. Mater. 42, 157 (2010).Google Scholar
Prasad, Y.V.R.K. and Sasidhara, S. eds.: Hot Working Guide, a Compendium of Processing Maps (ASM, Materials Park, Ohio, USA, 1997); p. 203.Google Scholar
Perrot, P.: Non-ferrous metal systems. Part 2. In Landolt-Börnstein—Group IV Physical Chemistry, Vol. 11C2 (Effenberg, G., Ilyenko, S., eds.; Berlin: Springer, 2007); p. 408.Google Scholar
Hill, R.: A self-consistent mechanics of composite materials. J. Mech. Phys. Solids 13, 213 (1965).Google Scholar
Suquet, P.M.: Overall potentials and extremal surfaces of power law or ideally plastic composites. J. Mech. Phys. Solids 41, 981 (1993).CrossRefGoogle Scholar
Lin, Y.C. and Chen, X.M.: A critical review of experimental results and constitutive descriptions for metals and alloys in hot working. Mater. Des. 32, 1733 (2011).CrossRefGoogle Scholar