Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-26T06:31:19.781Z Has data issue: false hasContentIssue false
  • English
  • Français

An Innovative System for Fretting Wear Testing Under Oscillating Normal Force

Published online by Cambridge University Press:  31 January 2011

M. Z. Huq ,
C. Butaye  and
J-P. Celis
M. Z. Huq
Affiliation:
Department of Metallurgy and Materials Engineering, Katholieke Universiteit Leuven, de Croylaan 2, B-3001 Leuven, Belgium
C. Butaye
Affiliation:
Department of Metallurgy and Materials Engineering, Katholieke Universiteit Leuven, de Croylaan 2, B-3001 Leuven, Belgium
J-P. Celis
Affiliation:
Department of Metallurgy and Materials Engineering, Katholieke Universiteit Leuven, de Croylaan 2, B-3001 Leuven, Belgium
Get access

Abstract

Material damage caused by fretting wear is of significant concern in many engineering applications. This paper describes the design and performance of a new machine for the laboratory investigation of fretting wear under oscillating normal force (fretting mode II). The test machine uses an electromagnetic actuator to impose an oscillating normal force between the contacting bodies at a constant force amplitude over a wide range of frequencies. The principle of the actuation mechanism and the fretting wear induced with this particular wear test configuration are outlined in detail. Normal force and electrical contact resistance were measured on-line during fretting mode II wear tests. The performance of the wear test machine is illustrated by data obtained for different materials combinations, namely, hard materials, such as high-speed steel and (Ti,Al)N coatings oscillating against alumina ball counterbodies, and soft materials, such as a tin coating oscillating against the same. In general, wearing of the counterbodies was observed in the slip region. It has been observed that hard coatings and bulk ceramics are prone to fretting fatigue cracking. The evolution of electrical contact resistance in the case of the self-mated soft tin coatings tested under fretting mode II conditions is also reported.

Type
Articles
Information
Journal of Materials Research , Volume 15 , Issue 7 , July 2000 , pp. 1591 - 1599
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Materials Evaluation under Fretting Conditions, edited by Brown, S.R. (ASTM Spec. Tech. Publ. 780, Warminster, PA, 1982), p. 1.CrossRefGoogle Scholar
2.Waterhouse, R.B., Fretting Wear, ASM Handbook Vol. 18, (ASM International, Herndon, VA, 1992), p. 242.Google Scholar
3.Begelinger, A. and De Gee, A.W.J, in AGARD Conference Proceedings, No. 161 (National Technical Information Service, Springfield, VA, 1974), p. 9.1.Google Scholar
4.Waterhouse, R.B., Fretting Fatigue (Elsvier Applied Science, London, United Kingdom, 1981).Google Scholar
5.Waterhouse, R.B., Fretting Corrosion (Pergamon, Oxford, United Kingdom, 1972).Google Scholar
6.Kennedy, P., Peterson, M.B., and Stallings, L., ASTM STP 780 (ASTM, Philadelphia, PA, 1982), p. 30.Google Scholar
7.Ko, P.L., J. Pressure Vessel Technol. 101, 125 (1979).CrossRefGoogle Scholar
8.Sandstrom, P.W., Sridharan, K., and Conard, J.R., Wear 166, 163 (1993).Google Scholar
9.Mohrbacher, H., Ph.D. Thesis, Katholieke Universiteit Leuven (1995).Google Scholar
10.Vingsbo, O. and Söderberg, S., Wear 126, 131 (1988).CrossRefGoogle Scholar
11.Friction and Wear of Ceramics, edited by Kennedy, P.J., Conte, A.A., Wintherton, E.P., Ives, L.K., and Peterson, M.B. (Marcel Dekker, New York, 1994), p. 79.Google Scholar
12.Ko, P.L., Thromp, J.J., and Weckwerth, M.K., Materials Evaluation under Fretting Conditions, ASTM STP 780 (ASTM, Philadelphia, PA, 1982), p. 86.CrossRefGoogle Scholar
13.Ruiz, C., Wang, Z.P., Webb, H.P., Standardisation of Fretting Fatigue Test Methods and Equipments, ASTM STP 1159, edited by Attia, Helmi and Waterhouse, R.B. (ASTM, Philadelphia, PA, 1992), p. 170.Google Scholar
14.Dobromirsky, J.M., in Standardisation of Fretting Fatigue Test Methods and Equipments, ASTM STP 1159, edited by Attia, Helmi and Waterhouse, R.B. (ASTM, Philadelphia, 1992), p. 60.CrossRefGoogle Scholar
15.Bill, R.C., Materials Evaluation under Fretting Conditions ASTM STP 780 (Philadelphia, PA, 1982), p. 165.Google Scholar
16.Timoshenko, S. and Goodier, J.N., Theory of Elasticity (McGraw-Hill, New York, 1951), p. 372.Google Scholar
17.Diao, D.F., Kato, K., and Hokkirigawa, K., ASME J. Tribol. 116, 860 (1994).CrossRefGoogle Scholar
18.Huq, M.Z. and Celis, J-P., Surf. Coat. Technol. 113, 242 (1999).Google Scholar
19.Huq, M.Z. and Celis, J-P., Wear 225–229, 53 (1999).CrossRefGoogle Scholar
20.Guiberteau, F., Padture, N.P., Cai, H., and Lawn, B.R., Philos. Mag. A 68, 1003 (1993).CrossRefGoogle Scholar
21.Themlin, J.M., Chtaïb, M., Henrard, L., Lambin, Ph., Darville, J., and Gilles, J.M., Phys. Rev. B 46, 2640 (1992).Google Scholar