Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-20T11:40:28.887Z Has data issue: false hasContentIssue false
  • English
  • Français

An improved energy method for determining Young’s modulus by instrumented indentation using a Berkovich tip

Published online by Cambridge University Press:  31 January 2011

Dejun Ma ,
Chung Wo Ong  and
Taihua Zhang
Dejun Ma
Affiliation:
Department of Mechanical Engineering, The Academy of Armored Forces Engineering, Beijing 100072, People’s Republic of China
Chung Wo Ong*
Affiliation:
Department of Applied Physics and Materials Research Center, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, People’s Republic of China
Taihua Zhang
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100080, People’s Republic of China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

We previously proposed a method for estimating Young’s modulus from instrumented nanoindentation data based on a model assuming that the indenter had a spherical-capped Berkovich geometry to take account of the bluntness effect. The method is now further improved by releasing the constraint on the tip shape, allowing it to have a much broader arbitrariness to range from a conical-tipped shape to a flat-ended shape, whereas the spherical-capped shape is just a special case in between. This method requires two parameters to specify a tip geometry, namely, a volume bluntness ratio Vr and a height bluntness ratio hr. A set of functional relationships correlating nominal hardness/reduced elastic modulus ratio (Hn/Er) and elastic work/total work ratio (We/W) were established based on dimensional analysis and finite element simulations, with each relationship specified by a set of Vr and hr. Young’s modulus of an indented material can be estimated from these relationships. The method was shown to be valid when applied to S45C carbon steel and 6061 aluminum alloy.

Keywords

Elastic properties
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 8 , August 2008 , pp. 2106 - 2115
Copyright
Copyright © Materials Research Society 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Pethica, J.B., Hutchings, R.Oliver, W.C.: Hardness measurement at penetration depth as small as 20 nm. Philos. Mag. A 48, 593 1983CrossRefGoogle Scholar
2Loubet, J.L., Georges, J.M., Marchesini, O.Meille, G.: Vickers indentation curves of magnesium oxide (MgO). J. Tribol. 106, 43 1984CrossRefGoogle Scholar
3Newey, D., Wilkens, M.A.Pollock, H.M.: An ultra-low-load penetration hardness tester. J. Phys. E.: Sci. Instrum. 15, 119 1982CrossRefGoogle Scholar
4Oliver, W.C.Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 1992CrossRefGoogle Scholar
5Pharr, G.M., Oliver, W.C.Brotzen, F.R.: On the generality of the relationship among contact stiffness, contact area, and elastic modulus during indentation. J. Mater. Res. 7, 613 1992CrossRefGoogle Scholar
6Oliver, W.C.Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 2004CrossRefGoogle Scholar
7Cheng, Y-T.Cheng, C.M.: Scaling, dimension analysis, and indentation measurements. Mater. Sci. Eng., R 44, 91 2004CrossRefGoogle Scholar
8Fischer-Cripps, A.C.: Nanoindentation Springer-Verlag New York 2004 39CrossRefGoogle Scholar
9Malzbender, J.de With, G.: Indentation load-displacement curve, plastic deformation, and energy. J. Mater. Res. 17, 502 2002CrossRefGoogle Scholar
10Venkatesh, T.A., Van Vliet, K.J., Giannakopoulos, A.E.Suresh, S.: Determination of elasto-plastic properties by instrumented sharp indentation: Guidelines for property extraction. Scr. Mater. 42, 833 2000CrossRefGoogle Scholar
11Giannakopoulos, A.E.Suresh, S.: Determination of elasto-plastic properties by instrumented sharp indentation. Scr. Mater. 40, 1191 1999CrossRefGoogle Scholar
12Cheng, Y-T.Cheng, C-M.: Relationships between hardness, elastic modulus, and the work of indentation. Appl. Phys. Lett. 73, 614 1998CrossRefGoogle Scholar
13Cheng, C-M.Cheng, Y-T.: On the initial unloading slope in indentation of elastic-plastic solids by an indenter with an axisymmetric smooth profile. Appl. Phys. Lett. 71, 2623 1997CrossRefGoogle Scholar
14Ni, W.Y., Cheng, Y.T., Chen, C.M.Grummon, D.S.: An energy-based method for analyzing instrumented spherical indentation experiments. J. Mater. Res. 19, 149 2004CrossRefGoogle Scholar
15Ma, D., Ong, C.W., Wong, S.F.He, J.: New method for determining Young’s modulus by non-ideally sharp indentation. J. Mater. Res. 20, 1498 2005CrossRefGoogle Scholar
16Ma, D., Ong, C.W.Wong, S.F.: New relationship between Young’s modulus and nonideally sharp indentation parameters. J. Mater. Res. 19, 2144 2004CrossRefGoogle Scholar
17Dao, M., Chollacoop, N., Van Vliet, K.J., Venkatesh, T.A.Suresh, S.: Computational modeling of the forward and reverse problems in instrumented sharp indentation. Acta Mater. 49, 3899 2001CrossRefGoogle Scholar
18Lichinchi, M., Lenardi, C., Haupt, J.Vitali, R.: Simulation of Berkovich nanoindentation experiments on thin films using finite element method. Thin Solid Films 312, 240 1998CrossRefGoogle Scholar
19Fischer-Cripps, A.C.: Use of combined elastic modulus in depth-sensing indentation with a conical indenter. J. Mater. Res. 18, 1043 2003CrossRefGoogle Scholar
20ABAQUS Version 6.2 Hibbitt, Karlsson & Sorensen, Inc. Pawtucket, RI 2001Google Scholar
21Bolshakov, A.Pharr, G.M.: Influences of pileup on the measurement of mechanical properties by load and depth sensing indentation techniques. J. Mater. Res. 13, 1049 1998CrossRefGoogle Scholar
22Vlassak, J.J.Nix, W.D.: Measuring the elastic properties of anisotropic materials by means of indentation experiments. J. Mech. Phys. Solids 42, 1223 1994CrossRefGoogle Scholar
23Vlassak, J.J.Nix, W.D.: Indentation modulus of elastically anisotropic half spaces. J. Mech. Phys. Solids 67, 1045 1993Google Scholar
24Vlassak, J.J., Ciavarella, M., Barber, J.R.Wang, X.: The indentation modulus of elastically anisotropic materials for indenters of arbitrary shape. J. Mech. Phys. Solids 51, 1701 2003CrossRefGoogle Scholar
25Hirth, J.P.Lothe, J.: Elastic Constants in Theory of Dislocations Krieger Publishing Company Malabar, FL 1982 837Google Scholar