Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-05T06:11:47.502Z Has data issue: false hasContentIssue false

Synthesis, microstructure evolution, and mechanical properties of (Cr1–xVx)2AlC ceramics by in situ hot-pressing method

Published online by Cambridge University Press:  12 May 2014

Jianfeng Zhu
Affiliation:
Key Laboratory of Auxiliary Chemistry & Technology for Chemical Industry, Ministry of Education, Shaanxi University of Science and Technology, Xi’an 710021, China
Hao Jiang*
Affiliation:
Key Laboratory of Auxiliary Chemistry & Technology for Chemical Industry, Ministry of Education, Shaanxi University of Science and Technology, Xi’an 710021, China
Fen Wang
Affiliation:
Key Laboratory of Auxiliary Chemistry & Technology for Chemical Industry, Ministry of Education, Shaanxi University of Science and Technology, Xi’an 710021, China
Qi Ma*
Affiliation:
Key Laboratory of Auxiliary Chemistry & Technology for Chemical Industry, Ministry of Education, Shaanxi University of Science and Technology, Xi’an 710021, China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Nearly dense and almost single-phase bulk (Cr1–xVx)2AlC (x = 0, 0.25, 0.5, 0.75, and 1.0) ceramics were successfully fabricated by in situ hot-pressing method using Cr, V, Al, and C powders as raw materials. A possible synthesis mechanism was proposed to explain the formation of (Cr1–xVx)2AlC solid solutions. The lattice parameters, microstructure, and mechanical properties of the (Cr1–xVx)2AlC ceramics were investigated in detail. The results indicated that the lattice parameters increased with the substitution of Cr by V and the aspect ratio of the grain changed from 1.4 to 3.2. The dependence of the mechanical properties on the V content was a single-peak type. The (Cr0.5V0.5)2AlC ceramic possessed the optimal mechanical performance and its Vickers hardness, flexural strength, and fracture toughness reached the maximum values of 5.18 GPa, 402 MPa, 5.91 MPa m1/2, respectively, due to the solid solution effect. The energy-consuming mechanisms of the material were also discussed.

Type
Articles
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Barsoum, M.W.: The Mn+1AXn phases: A new class of solids; thermodynamically stable nanolaminates. Prog. Solid State Chem. 28, 201 (2000).CrossRefGoogle Scholar
Schuster, J.C., Nowotny, H., and Vaccaro, C.: The ternary systems: Cr-Al-C, V-Al-C, and Ti-Al-C and the behavior of H-Phases (M2AlC). J. Solid State Chem. 32(2), 213 (1980).CrossRefGoogle Scholar
Hu, C.F., Zhang, H.B., Li, F.Z., Huang, Q., and Bao, Y.W.: New phases’ discovery in MAX family. Int. J. Refract. Met. Hard Mater. 36, 300 (2013).Google Scholar
Tian, W.B., Wang, P.L., Zhang, G.J., Kan, Y.M., Li, Y.X., and Yan, D.S.: Synthesis and thermal and electrical properties of bulk Cr2AlC. Scr. Mater. 54(5), 841 (2006).CrossRefGoogle Scholar
Ying, G.B., He, X.D., Li, M.W., Han, W.B., He, F., and Du, S.Y.: Synthesis and mechanical properties of high-purity Cr2AlC ceramic. Mater. Sci. Eng., A 528(6), 2635 (2011).CrossRefGoogle Scholar
Ai, T.T.: High-temperature oxidation behavior of un-dense Ti3AlC2 material at 1000 °C in air. Ceram. Int. 38(3), 2537 (2012).CrossRefGoogle Scholar
Lin, Z.J., Li, M.S., Wang, J.Y., and Zhou, Y.C.: High-temperature oxidation and hot corrosion of Cr2AlC. Acta Mater. 55(18), 6182 (2007).Google Scholar
Xiao, L.O., Li, S.B., Song, G.M., and Sloof, W.G.: Synthesis and thermal stability of Cr2AlC. J. Eur. Ceram. Soc. 31(8), 1497 (2011).Google Scholar
Low, I.M., Pang, W.K., Kennedy, S.J., and Smith, R.I.: High-temperature thermal stability of Ti2AlN and Ti4AlN3: A comparative diffraction study. J. Eur. Ceram. Soc. 31, 159 (2011).Google Scholar
Tian, W.B., Sun, Z.M., Hashimoto, H., and Du, Y.L.: Synthesis, microstructure and properties of (Cr1-x V x )2AlC solid solutions. J. Alloys Compd. 484, 130 (2009).Google Scholar
Salama, I., El-Raghy, T., and Barsoum, M.W.: Synthesis and mechanical properties of Nb2AlC and (Ti,Nb)2AlC. J. Alloys Compd. 347, 271 (2002).Google Scholar
Meng, F.L., Zhou, Y.C., and Wang, J.Y.: Strengthening of Ti2AlC by substituting Ti with V. Scr. Mater. 53(12), 1369 (2005).Google Scholar
Barsoum, M.W., Ali, M., and El-Raghy, T.: Processing and characterization of Ti2AlC, Ti2AlN and Ti2AlC0.5N0.5 . Metall. Mater. Trans. A 31(7), 1857 (2000).Google Scholar
Li, S.B., Bei, G.P., Li, C.W., Ai, M.X., Zhai, H.X., and Zhou, Y.: Synthesis and deformation microstructure of Ti3SiAl0.2C1.8 solid solution. Mater. Sci. Eng., A 441, 202 (2006).Google Scholar
Ai, M.X., Zhai, H.X., Zhou, Y., Tang, Z.Y., Huang, Z.Y., Zhang, Z.L., and Li, S.B.: Synthesis of Ti3AlC2 powders using Sn as an additive. J. Am. Ceram. Soc. 89(3), 1114 (2006).Google Scholar
Ganguly, A., Zhen, T., and Barsoum, M.W.: Synthesis and mechanical properties of Ti3GeC2 and Ti3(Si x Ge1−x )C2 (x = 0.5, 0.75) solid solutions. J. Alloys Compd. 376, 287 (2004).CrossRefGoogle Scholar
Radovic, M., Ganguly, A., and Barsoum, M.W.: Elastic properties and phonon conductivities of Ti3Al(C0.5,N0.5)2 and Ti2Al(C0.5,N0.5) solid solutions. J. Mater. Res. 23(6), 1517 (2008).Google Scholar
Wang, J.Y. and Zhou, Y.C.: Ab initio elastic stiffness of nano-laminate (M x M′2–x AlC)AlC (M and M′ = Ti, V, Cr) solid solution. J. Phys.: Condens. Matter 16, 2819 (2004).Google Scholar
Sun, Z., Ahuja, R., and Schneider, J.M.: Theoretical investigation of the solubility in (M x M′2–x AlC)AlC (M and M′ = Ti, V, Cr). Phys. Rev. B 68(22), 224112 (2003).Google Scholar
Yeh, C.L. and Yang, W.J.: Formation of MAX solid solutions (Ti,V)2AlC and (Cr,V)2AlC with Al2O3 addition by SHS involving aluminothermic reduction. Ceram. Int. 39(7), 7537 (2013).Google Scholar
Yu, W.B., Li, S.B., and Sloof, W.G.: Microstructure and mechanical properties of a Cr2Al(Si)C solid solution. Mater. Sci. Eng., A 527, 5997 (2010).CrossRefGoogle Scholar
Clementi, E., Raimondi, D.L., and Reinhardt, W.P.: Atomic screening constants from SCF functions. II. Atoms with 37 to 86 electrons. J. Chem. Phys. 47(4), 1300 (1967).Google Scholar
Barsoum, M.W., Murugaiah, A., Kalidindi, S.R., Zhen, T., and Gogotsi, Y.: Kink bands, nonlinear elasticity and nanoindentations in graphite. Carbon 42, 1435 (2004).Google Scholar
Zhou, A.G. and Barsoum, M.W.: Kinking nonlinear elastic deformation of Ti3AlC2, Ti2AlC, Ti3Al(C0.5,N0.5)2 and Ti2Al(C0.5,N0.5). J. Alloys Compd. 498(1), 62 (2010).Google Scholar
Hu, C.F., Li, F.Z., He, L.F., Liu, M.Y., Zhang, J., Wang, J.M., Bao, Y.W., Wang, J.Y., and Zhou, Y.C.: In situ reaction synthesis, electrical and thermal, and mechanical properties of Nb4AlC3 . J. Am. Ceram. Soc. 91(7), 2258 (2008).Google Scholar
Hu, C.F., He, L.F., Liu, M.Y., Wang, X.H., Wang, J.Y., Li, M.S., and Bao, Y.W., and Zhou, Y.C.: In situ reaction synthesis and mechanical properties of V2AlC. J. Am. Ceram. Soc. 91(12), 4029 (2008).Google Scholar
Ryen, Ø., Holmedal, B., Nijs, O., Nes, E., Sjölander, E., and Ekström, H.E.: Strengthening mechanisms in solid solution aluminum alloys. Metall. Mater. Trans. A 37(6), 1999 (2006).Google Scholar