Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-26T18:09:52.816Z Has data issue: false hasContentIssue false
  • English
  • Français

Structural and tribological characterization of Ti–In–N films deposited by magnetron sputter deposition

Published online by Cambridge University Press:  07 November 2011

Margaret A. Nowicki ,
James E. Krzanowski  and
Jose L. Endrino
Margaret A. Nowicki
Affiliation:
Department of Mechanical Engineering, University of New Hampshire, Durham, New Hampshire
James E. Krzanowski*
Affiliation:
Department of Mechanical Engineering, University of New Hampshire, Durham, New Hampshire
Jose L. Endrino
Affiliation:
Instituto de Ciencia de Materiales de Madrid (CSIC), 28049 Madrid, Spain
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

TiN–indium composite films were deposited by simultaneous sputtering of titanium and indium in a mixed Argon/Nitrogen atmosphere and characterized for tribological applications. Film compositions showed a nonlinear behavior as a function of sputter gun power. For films deposited at −50 V bias, and containing less than 29 relative percent indium, the films had a face centered cubic structure, but at higher indium contents (63–82%) the structure was not consistent with either TiN or indium. At −150 V bias, the films had either the TiN structure, In-type structure, or a mixture of the two. Atomic force microscopy images showed the formation of semispherical drops on the surface of the samples deposited at −50 V bias voltage, whereas at −150 V bias voltage the samples exhibited a smooth coating surface with occasional ellipsoidal blisters. Nanoindentation test of the films shows low hardness (5–12 GPa), but tribological testing showed that frictional behavior can be improved by moderate heating before testing, suggesting indium segregation to the surface.

Keywords

NitrideThin filmIn
Type
Articles
Information
Journal of Materials Research , Volume 27 , Issue 5: Focus Issue: Plasma and Ion-Beam Assisted Materials Processing , 14 March 2012 , pp. 850 - 856
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Simmonds, M.C., Savan, A., Van Swygenhoven, H., Pfluger, E., and Mikhailov, S.: Structural, morphological, chemical and tribological investigations of sputter deposited MoSx/metal multilayer coatings. Surf. Coat. Technol. 108, 340 (1998).CrossRefGoogle Scholar
2.Endrino, J.L., Nainaparampil, J.J., and Krzanowski, J.E.: Microstructure and vacuum tribology of TiC–Ag composite coatings deposited by magnetron sputtering-pulsed laser deposition. Surf. Coat. Technol. 157, 95 (2002).CrossRefGoogle Scholar
3.Endrino, J., Nainaparampril, J.J., and Krzanowski, J.E.: Magnetron sputter deposition of WC–Ag and TiC–Ag coatings and their frictional properties in vacuum environments. Scr. Mater. 74, 613 (2002).CrossRefGoogle Scholar
4.Mulligan, C.P., Blanchet, T.A., and Gall, D.: CrN–Ag nanocomposite coatings: Tribology at room temperature and during a temperature ramp. Surf. Coat. Technol. 204, 1388 (2010).CrossRefGoogle Scholar
5.Mulligan, C.P., Blanchet, T.A., and Gall, D.: CrN–Ag nanocomposite coatings: High-temperature tribological response. Wear 269, 125 (2010).CrossRefGoogle Scholar
6.Narayan, R.J., Wang, H., and Tiwari, A.: Nanostructured DLC-Ag composites for biomedical applications, in Surface Engineering 2002—Synthesis, Characterization and Applications, edited by Kumar, A., Meng, W.J., Cheng, Y-T., Zabinski, J.S., Doll, G.L., and Veprek, S. (Mater. Res. Soc. Symp. Proc. 750, Warrendale, PA, 2003), p. 205.Google Scholar
7.Voevodin, A.A., Fitz, T.A., Hu, J.J., and Zabinski, J.S.: Nanocomposite tribological coatings with “chameleon” surface adaptation. J. Vac. Sci. Technol. A 20, 1434 (2003).CrossRefGoogle Scholar
8.Voevodin, A.A., Hu, J.J., Jones, J.G., Fitz, T.A., and Zabinski, J.S.: Growth and structural characterization of yttria-stabilized zirconia-gold nanocomposite films with improved toughness. Thin Solid Films 401, 187 (2001).CrossRefGoogle Scholar
9.Krzanowski, J.E., Endrino, J.L., Nainaparampil, J.J., and Zabinski, J.S.: Composite coatings incorporating solid lubricant phases. J. Mater. Eng. Perform. 13, 439 (2004).CrossRefGoogle Scholar
10.Krzanowski, J.E.: Phase formation and phase separation in multiphase thin film hard coatings. Surf. Coat. Technol. 188, 376 (2004).CrossRefGoogle Scholar
11.Fox-Rabinovich, G.S., Bushe, N.A., Kovalev, A.I., Korshunov, S.N., Shuster, L.Sh., and Dosbaeva, G.K.: Impact of ion modification of HSS surfaces on the wear resistance of cutting tools with surface engineered coatings. Wear 249, 1051 (2001).CrossRefGoogle Scholar
12.Guleryuz, G.C., Krzanowski, J.E., Veldhuis, S.C., Fox-Rabinovich, G.S.: Machining performance of TiN coatings incorporating indium as a solid lubricant. Surf. Coat. Technol. 203, 3370 (2009).CrossRefGoogle Scholar