Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-26T20:13:44.508Z Has data issue: false hasContentIssue false
  • English
  • Français

Secondary IMC formation induced by Kirkendall voiding in Cu/Sn–3.5Ag solder joints

Published online by Cambridge University Press:  31 January 2011

S.H. Kim  and
Jin Yu
Jin Yu*
Affiliation:
Electronic Packaging Laboratory, Department of Materials Science and Engineering, KAIST, Yuseong-gu, Daejeon 305-701, South Korea
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

In this investigation on the formation of multiple-layered Kirkendall voids at Cu/Sn–3.5Ag solder joints, Sn–3.5Ag solder balls were reacted with Cu under bump metallurgy (UBM), which was electroplated using bis-sodium sulfopropyl–disulfide, C6H12O6S4Na2 (SPS) additive. The sequence of multilayer Kirkendall voids and Cu–Sn IMC (intermetallic compounds) formations are explained with the aid of cross-sectional scanning electron microscopy (SEM) micrographs and schematic diagrams. During the aging treatment at 150 °C, layers of Cu6Sn5/Cu3Sn formed at the solder joints and Kirkendall voids nucleated at the Cu3Sn/Cu interface as a result of the segregation of residual S originating from SPS. However, with Kirkendall void growth, the net section area of the Cu/Cu3Sn interface decreased and the Cu flux into Cu3Sn was inhibited. As the atomic ratio of Cu against Sn in the Cu3Sn dropped, transformation of Cu3Sn into Cu6Sn5 ensued. Subsequent diffusion of Sn atoms into the remaining Cu UBM through the remaining ligament of the Cu6Sn5/Cu interface precipitated secondary Cu3Sn beneath the primary Cu3Sn/Cu interface, and the secondary Kirkendall voids formed at the new Cu3Sn/Cu interface and so on.

Keywords

Phase TransformationSolderingDiffusion
Type
Articles
Information
Journal of Materials Research , Volume 25 , Issue 9 , September 2010 , pp. 1854 - 1858
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Tu, K.N., Thompson, R.D.Kinetics of interfacial reaction in bimetallic CuSn thin films. Acta Metall. 30, 947 (1982)CrossRefGoogle Scholar
2.Zeng, K., Stierman, R., Ciu, T.C., Edwards, D., Ano, K., Tu, K.N.Kirkendall void formation in eutectic SnPb solder joints on bare Cu and its effect on joint reliability. J. Appl. Phys. 97, 024508 (2005)CrossRefGoogle Scholar
3.Ahat, S., Sheng, M., Luo, L.Microstructure and shear strength evolution of SnAg/Cu surface mount solder joint during aging. J. Electron. Mater. 30, 1317 (2001)CrossRefGoogle Scholar
4.Mei, Z., Ahmad, M., Hu, M., Ramakrishna, G.Kirkendall voids at Cu/solder interface and their effects on solder joint reliabilityProceedings 55th Electronic Components and Technology Conference Vol. 1 (Orlando, FL 2005)415Google Scholar
5.Kim, J.Y., Yu, J.Effects of residual impurities in electroplated Cu on the Kirkendall void formation during soldering. Appl. Phys. Lett. 92, 092109 (2008)CrossRefGoogle Scholar
6.Anderson, I.E., Harringa, J.L.Suppression of void coalescence in thermal aging of tin–silver–copper-X solder joints. J. Electron. Mater. 35, 94 (2006)CrossRefGoogle Scholar
7.Date, M., Tu, K.N., Shoji, T., Fujiyoshi, M., Sato, K.Interfacial reactions and impact reliability of Sn–Zn solder joints on Cu or electroless Au/Ni(P) bond-pads. J. Mater. Res. 19, 2887 (2004)CrossRefGoogle Scholar
8.Jee, Y.K., Ko, Y.H., Yu, J.Effects of Zn addition on the drop reliability of Sn–3.5Ag–xZn/Ni(P) solder joints. J. Mater. Res. 22, 1879 (2007)CrossRefGoogle Scholar
9.Yang, S.C., Ho, C.E., Chang, C.W., Kao, C.R.Strong Zn concentration effect on the soldering reactions between Sn-based solders and Cu. J. Mater. Res. 21, 2436 (2006)CrossRefGoogle Scholar
10.Balluffi, R.W.The supersaturation and precipitation of vacancies during diffusion. Acta Metall. 2, 194 (1954)CrossRefGoogle Scholar
11.Balluffi, R.W., Seigle, L.L.Effect of grain boundaries upon pore formation and dimensional changes during diffusion. Acta Metall. 3, 170 (1955)CrossRefGoogle Scholar
12.Chiu, T.C., Zeng, K., Stierman, R., Edwards, D., Ano, K.Effect of thermal aging on board level drop reliability for Pb-free BGA packagesProceedings 54th Electronic Components and Technology Conference (Las Vegas, NV 2004)1256Google Scholar
13.Yang, W., Messler, R.W. Jr.Microstructure evolution of eutectic Sn–Ag solder joints. J. Electron. Mater 23, 765 (1994)CrossRefGoogle Scholar
14.Laurila, T., Vourinen, V., Kivilahti, J.K.Interfacial reactions between lead-free solders and common base materials. Mater. Sci. Eng., R 49, 1 (2005)CrossRefGoogle Scholar
15.Jin, Yu., Kim, J.Y.Effects of residual S on Kirkendall void formation at Cu/Sn–3.5Ag solder joints. Acta Mater 56, 5514 (2008)Google Scholar
16.Kim, J.Y., Yu, J., Kim, S.H.Effects of sulphide forming element additions on the Kirkendall void formation and drop impact reliability of Cu/Sn–3.5Ag solder joints. Acta Mater 57, 5001 (2009)CrossRefGoogle Scholar
17.Birchenall, C.E.Physical Metallurgy (McGraw-Hill, New York 1959)Google Scholar
18.Schaffer, M., Fournelle, R.A., Liang, J.Theory for intermetallic phase growth between Cu and liquid Sn–Pb solder based on grain boundary diffusion control. J. Electron. Mater. 27, 1167 (1998)CrossRefGoogle Scholar
19.Mei, Z., Sunwoo, A.J., Morris, J.W.Jr.: Analysis of low-temperature intermetallic growth in copper–tin diffusion couples. Metall. Trans. A 23, 857 (1992)CrossRefGoogle Scholar
20.Kim, H.K., Tu, K.N.Kinetic analysis of the soldering reaction between eutectic SnPb alloy and Cu accompanied by ripening. Phys. Rev. B 53, 16027 (1996)CrossRefGoogle ScholarPubMed
21.Kim, J.Y., Sohn, Y.C., Yu, J.Effect of Cu content on the mechanical reliability of Ni/Sn–3.5Ag system. J. Mater. Res. 22, 770 (2007)CrossRefGoogle Scholar
22.Song, J.Y., Yu, J., Lee, T.Y.Effects of reactive diffusion on stress evolution in Cu-Sn film. Scr. Mater. 51, 167 (2004)CrossRefGoogle Scholar