Hostname: page-component-78c5997874-4rdpn Total loading time: 0 Render date: 2024-11-09T07:35:04.075Z Has data issue: false hasContentIssue false
  • English
  • Français

Preparation of phase homogeneous Mn–Zn ferrite powder by spray pyrolysis

Published online by Cambridge University Press:  31 January 2011

Xinyu Zhao ,
Baicun Zheng ,
Hongchen Gu ,
Chunzhong Li ,
Shi Chang Zhang  and
P. Darrell Ownby
Xinyu Zhao
Affiliation:
Institute of Technical Chemical Physics, East China University of Science and Technology, Shanghai, People's Republic of China
Baicun Zheng
Affiliation:
Institute of Technical Chemical Physics, East China University of Science and Technology, Shanghai, People's Republic of China
Hongchen Gu
Affiliation:
Institute of Technical Chemical Physics, East China University of Science and Technology, Shanghai, People's Republic of China
Chunzhong Li
Affiliation:
Institute of Technical Chemical Physics, East China University of Science and Technology, Shanghai, People's Republic of China
Shi Chang Zhang
Affiliation:
Department of Ceramic Engineering, University of Missouri–Rolla, Rolla, Missouri 65401
P. Darrell Ownby*
Affiliation:
Department of Ceramic Engineering, University of Missouri–Rolla, Rolla, Missouri 65401
*
a) Address all correspondence to this author.
Get access

Abstract

Two kinds of aqueous precursor solutions are used to synthesize Mn–Zn ferrite powders: (i) nitrate (NO) precursor—derived from solutions of Mn(NO3)2, Zn(NO3)2, and Fe(NO3)3; and (ii) acetate (AC) precursor—derived from solutions of Mn(CH3COO)2, Zn(CH3COO)2, and Fe(NO3)3. The composition of the powders synthesized from the precursor AC is very uniform, whereas powders derived from the precursor NO have Mn and Zn segregated on the particle surfaces. In addition, the powders synthesized from precursor AC are solid spherical particles with fine porosity, whereas many hollow and fragmented particles are observed in the powder derived from precursor NO. Overall, the properties of Mn–Zn ferrite cores prepared from the precursor AC are superior to those prepared from the precursor NO. The reasons for the differences are explained and described in detail. The AC precursor powders synthesized by spray pyrolysis produced Mn–Zn ferrite cores with good magnetic properties.

Type
Articles
Information
Journal of Materials Research , Volume 14 , Issue 7 , July 1999 , pp. 3073 - 3082
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Messing, G.L., Zhang, S.C., and Jayanthi, G.V., J. Am. Ceram. Soc. 76(11), 2707 (1993).CrossRefGoogle Scholar
2.Vollath, D. and Sickafus, K.E., J. Mater. Sci. 28, 5943 (1993).CrossRefGoogle Scholar
3.Rozman, M. and Drofenik, M., J. Am. Ceram. Soc. 78(9), 2449 (1995).CrossRefGoogle Scholar
4.Grurav, A., Kodas, T.T., Pluym, P., et al., Aerosol Sci. Technol. 19 (4), 411 (1993).CrossRefGoogle Scholar
5.Suyama, Y. and Kato, A., Ceram. Int. 8(1), 17 (1982).CrossRefGoogle Scholar
6.Imai, H., Takami, K., and Naito, M., Mater. Res. Bull. 19(10), 1293 (1984).CrossRefGoogle Scholar
7.Gadalla, A.M. and Yu, H-F., J. Mater. Res. 5, 2923 (1990).CrossRefGoogle Scholar
8.Kodas, T.T., Engler, E.M., Lee, V.Y., et al., Appl. Phys. Lett. 52 (19), 1622 (1988).CrossRefGoogle Scholar
9.Chao, C.H. and Ownby, P.D., J. Mater. Sci. 30, 6136 (1995).CrossRefGoogle Scholar
10.Chadda, S., Ward, T.L., Carin, A., Kodas, T.T., et al., J. Aerosol Sci. 22(5), 601 (1991).CrossRefGoogle Scholar
11.Lo, W., Cardwell, O.A., Dung, S.L., and Barter, R.G., J. Mater. Res. 11, 39 (1996).CrossRefGoogle Scholar
12.Tohge, N., Tatsumisago, M., and Minami, T., J. Am. Ceram. Soc. 74 (9), 2117 (1991).CrossRefGoogle Scholar
13.Senzaki, Y., Caruso, J., Hampden-Smith, M.J., Kodas, T.T., et al., J. Am. Ceram. Soc. 78(11), 2973 (1995).CrossRefGoogle Scholar
14.Li, Q. and Sorensen, C.M., Aerosol Sci. Tech. 19(4) (1993).Google Scholar
15.X-Ray Diffraction Procedure for Polycrystalline and Amorphous Materials, 2nd. edited by Klug, H.P. and Alexander, L.E. (John Wiley & Sons, New York, 1974), p. 534.Google Scholar
16.Zhang, S.C. and Messing, G.L., J. Am. Ceram. Soc. 73(1), 61 (1990).CrossRefGoogle Scholar
17.CRC Handbook of Chemistry and Physics, 70th edition, edited by Weast, R.C., (CRC Press, Florida, 1989).Google Scholar
18.Jayanthi, G.V., Zhang, S.C., and Messing, G.L., Aerosol. Sci. Technol. 19(4), 478 (1993).CrossRefGoogle Scholar
19.Sproson, D.W. and Messing, G.L., Ceram. Powder Sci., edited by Messing, G.L.et al. (Am. Ceram. Soc., Columbus, OH, 1989), p. 99.Google Scholar
20.Zhao, Xinyu, MS Thesis, East China University of Science and Technology, Shanghai.Google Scholar
21.Duncan, J.F. and Steward, D.J., Trans. Farad. Soc. 63, 1031 (1967).CrossRefGoogle Scholar
22.Toolenaar, F.J.C.M, J. Mater. Sci. 24, 1089 (1989).CrossRefGoogle Scholar
23.Ito, M., Senna, M., and Kuno, H., in Ferrites, (Proceedings of International Conference on Ferrites, ICF-4, Tokyo, Japan, 1980), p. 50.Google Scholar
24.Toolenaar, F.J.C.M and Verhees, M.T.J, J. Mater. Sci. 23, 856 (1988).CrossRefGoogle Scholar