Hostname: page-component-586b7cd67f-l7hp2 Total loading time: 0 Render date: 2024-11-26T12:05:30.189Z Has data issue: false hasContentIssue false
  • English
  • Français

Optimization of traveling magnetic field for horizontal continuous casting of thin slab containing tin phosphor bronze

Published online by Cambridge University Press:  27 June 2017

Qi Zhang  and
Tingju Li
Qi Zhang*
Affiliation:
Department of Mechanical Engineering, Qingdao Technological University, Qingdao 266033, Shandong, China
Tingju Li
Affiliation:
School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, Liaoning, China
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

To improve the quality of horizontal continuous casting bronze thin slab, especially the end quality of the thin slab, three methods were proposed; (i) using silicon steel sheet at the ends of the traveling magnetic field (TMF), (ii) change in the length of TMF, and (iii) reduction in the ends current intensity of TMF. Then, the effect of these methods on the magnetic field, flow and solidification of thin slab was studied both numerically and experimentally. Results show that the use of silicon steel sheet is the best method to modify the magnetic field intensity distribution. Due to the electromagnetic field shielding effect of silicon steel sheet, when the silicon steel sheet with 150 mm length and 0.5 mm thickness was applied, the magnetic field intensity at the ends of TMF was reduced to about half of the original. However, the magnetic field intensity in the middle of TMF did not change, which assists the elimination of the strong flow of the melt at the ends of the mold and uniform the solidification shell of the melt. Then, the bronze thin slab can be successfully cast without any crack defects at the ends.

Keywords

horizontal continuous castingtraveling magnetic fieldends qualitytin phosphor bronze thin slabsilicon steel sheet
Type
Articles
Information
Journal of Materials Research , Volume 32 , Issue 18 , 28 September 2017 , pp. 3532 - 3539
Check for updates
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Michael E. McHenry

References

REFERENCES

Guo, M., Liu, R., and Sun, Z.: Optimization of technological factors on QSn6.5-0.1 in horizontal continuous casting. Cast. Technol. 26, 591 (2005).Google Scholar
Hwang, J.D., Li, B.J., Hwang, W.S., and Hu, C.T.: Comparison of phosphor bronze metal sheet produced by twin roll casting and horizontal continuous casting. J. Mater. Eng. Perform. 7, 495 (1998).Google Scholar
Lu, J.P., Dong, F.W., and Lei, S.L.: Preliminary analysis of cause of cracks in QSn6.5-0.1 strip produced by horizontal continuous casting. Shanghai Nonferrous Met. 23, 62 (2002).Google Scholar
Bai, B.: Application of electromagnetic stirring technology in continuous casting. Foreign Steel 11, 13 (1992).Google Scholar
Li, T.J. and Jin, J.Z.: Current status and future potential for electromagnetic processing of materials. Mater. Rev. 14, 12 (2000).Google Scholar
Spinelli, J.E., Tosetti, J.P., Santos, C.A., Spim, J.A., and Garcia, A.: Microstrucutre and solidification thermal parameters in thin strip continuous casting of a stainless steel. J. Mater. Process. Technol. 150, 255 (2004).Google Scholar
Kim, M-G., Sung, S-Y., and Kim, Y-J.: Microstructure, metal-mold reaction and fluidity of investment cast-TiAl alloys. Mater. Trans. 45, 536 (2004).CrossRefGoogle Scholar
Yu, Z., Li, W., Deng, K., Lei, Z., and Ren, M.: Flow and solidification of copper thin-slab in horizontal continuous casting with electromagnetic stirring. Spec. Cast. Nonferrous Alloys 28, 229 (2008).Google Scholar
Li, W., Yu, Z., and Deng, K.: Flow and solidification characteristics of melt under electromagnetic stirring in horizontal continuous casting of copper thin-slab. Trans. Nonferrous Met. Soc. China 18, 1058 (2008).Google Scholar
Hui, C., Li, T., Jin, W., and Guo, J.: Research on horizontal electromagnetic continuous casting of Sn–P bronze strip plate. Rare Met. Mater. Eng. 37, 721 (2008).Google Scholar
Li, J., Jin, K., Zhang, X.G., Ru, Q.Y., Zhou, W.L., and Wang, Y.M.: Effect of electromagnetic field on quality of horizontal continuous casting QSn6.5-0.1 strip. Non-Met. Proc. 35, 15 (2006).Google Scholar
Thomas, B.G.: Modeling of continuous casting defects related to mold fluid flow. Iron Steel Technol. 3, 2 (2006).Google Scholar
Dahle, A.K. and StJohn, D.H.: Rheological behaviour of the mushy zone and its effect on the formation of casting defects during solidification. Acta Mater. 47, 31 (1998).Google Scholar
Yamaguchi, J., Nakashima, T., and Sawai, T.: Change and development of continuous casting technology. Nippon Steel Tech. Rep. 104, 13 (2013).Google Scholar
Zeng, J., Chen, W., Wang, Q., and Wang, G.: Improving inner quality in continuous casting rectangular billets: Comparison between mechanical soft reduction and final electromagnetic stirring. Trans. Indian Inst. Met. 69, 1623 (2016).Google Scholar
Zhang, H., Nagaumi, H., and Cui, J.: Coupled modeling of electromagnetic field, fluid flow, heat transfer and solidification during low frequency electromagnetic casting of 7XXX aluminum alloys. Part II: The effects of electromagnetic parameters on casting processes. Mater. Sci. Eng., A 448, 177 (2007).Google Scholar
Feng, C.: Electromagnetic Field (People’s Education Press, Beijing, 1985); p. 493.Google Scholar
Wang, F.: Computational Fluid Dynamics Analysis (Tsinghua University Education Press, Beijing, 2004); p. 272.Google Scholar
Ge, S., Isac, M., and Guthrie, R.I.L.: The computational fluid dynamic (CFD) modeling of horizontal single belt casting (HSBC) processing of Al–Mg–Sc–Zr alloy strips. Mater. Sci. Eng., B 46, 2264 (2015).Google Scholar
Zhang, Q. and Yi, C.L.: Research of force and fluid during horizontal continuous casting of QSn6.5-0.1 strip by imposing double traveling electromagnetic field. Int. J. Adv. Comp. Technol. 4, 536 (2012).Google Scholar
Supplementary material: Image

Zhang and Li supplementary material

Supplementary Figure

Download Zhang and Li supplementary material(Image)
Image 327.6 KB