Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-27T04:02:11.642Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructures, surface areas, and oxygen absorption of Ti and Ti–Zr–V films grown using glancing-angle sputtering

Published online by Cambridge University Press:  31 January 2011

Chien-Cheng Li ,
Jow-Lay Huang ,
Ran-Jin Lin ,
Hong-Ping Lin ,
Ding-Fwu Lii  and
Chuan-Pu Liu
Chien-Cheng Li
Affiliation:
Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan, Republic of China
Jow-Lay Huang
Affiliation:
Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan, Republic of China
Ran-Jin Lin
Affiliation:
Intellectual Property Exchange Limited, Hsinchu 310, Taiwan, Republic of China
Hong-Ping Lin
Affiliation:
Department of Chemistry, National Cheng Kung University, Tainan 701, Taiwan, Republic of China
Ding-Fwu Lii
Affiliation:
Department of Electrical Engineering, Cheng Shiu University, Kaohsiung 833, Taiwan, Republic of China
Chuan-Pu Liu
Affiliation:
Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan, Republic of China
Get access

Abstract

Highly porous Ti and TiZrV getter film coatings have been successfully grown on (100) silicon substrates using the glancing-angle direct-current magnetron sputtering method. The evolution of the microstructures of the Ti and the TiZrV films strongly depends on the sputtering flux rate, surface diffusion rate, nucleation rate, compositions, and self-shadowing geometry of the nuclei on the sputtering flux. The larger the glancing angle, the higher the porosity and specific surface area of the Ti and TiZrV films. The weight-gain results strongly depend on several factors, such as specific surface area, the surface structure of the getter film, the diffusion rate of O in the getter film, the reactivity of Ti, Zr, and V on O, and the order of the stabilities of Ti, Zr, and V oxides on the film’s surface. Porous Ti film absorbs oxygen better than porous TiZrV film does due to its higher surface area and the high diffusion rate of O in Ti films.

Keywords

SputteringNanostructureAbsorption
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 2 , February 2008 , pp. 579 - 587
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Benvenuti, C., Chiggiato, P., Pinto, P. Costa, Prodromides, A.Ruzinov, V.: Influence of the substrate coating temperature on the vacuum properties of Ti–Zr–V non-evaporable getter films. Vacuum 71, 307 2003CrossRefGoogle Scholar
2Prodromides, A.E., Scheuerlein, C.Taborelli, M.: Lowering the activation temperature of TiZrV non-evaporable getter films. Vacuum 60, 35 2001CrossRefGoogle Scholar
3Drbohlav, J.Matloin, V.: Static SIMS study of Ti, Zr, V and Ti–Zr–V NEG activation. Vacuum 71, 323 2003CrossRefGoogle Scholar
4Porta, P. della: Gas problem and gettering in sealed-off vacuum devices. Vacuum 47, 771 1996CrossRefGoogle Scholar
5Engelsen, D. denFerrario, B.: Gettering by Ba films in color cathode ray tubes. J. Vac. Sci. Technol., B 22(2), 809 2004CrossRefGoogle Scholar
6Li, C-C., Huang, J-L., Lin, R-J., Chang, H-K.Ting, J-M.: Fabrication and characterization of non-evaporable porous getter films. Surf. Coat. Technol. 200, 1351 2005CrossRefGoogle Scholar
7Li, C-C., Huang, J-L., Lin, R-J.Lii, D-F.: Preparation and characterization of non-evaporable porous Ti–Zr–V getter films. Surf. Coat. Technol. 201, 3977 2006CrossRefGoogle Scholar
8Ohring, M.: The Materials Science of Thin Films, 2nd ed.Academic Press San Diego, CA 2002 495, 558Google Scholar
9Thornton, J.A.: Influence of apparatus geometry and deposition conditions on the structure and topography of thick sputtered coating. J. Vac. Sci. Technol. 11, 666 1974CrossRefGoogle Scholar
10Messier, R., Giri, A.P.Roy, R.A.: Revised structure zone model for thin film physical structure. J. Vac. Sci. Technol., A 2, 500 1984CrossRefGoogle Scholar
11Sit, J.C., Vick, D., Robbie, K.Brett, M.J.: Thin film microstructure control using glancing angle deposition by sputtering. J. Mater. Res. 14, 1197 1999CrossRefGoogle Scholar
12Abelmann, L.Lodder, C.: Oblique evaporation and surface diffusion. Thin Solid Films 305, 1 1997CrossRefGoogle Scholar
13Robbie, K., Shafai, C.Brett, M.J.: Thin films with manometer-scale pillar microstructure. J. Mater. Res. 14, 3158 1999CrossRefGoogle Scholar
14Dick, B., Brett, M.J.Smy, T.: Investigation of substrate rotation at glancing angle incidence on thin-film morphology. J. Vac. Sci. Technol., B 21, 2569 2003CrossRefGoogle Scholar
15Kelly, P.J., O’Brien, J.Arnell, R.D.: The production of porous and chemically reactive coatings by magnetron sputtering. Vacuum 74, 1 2004CrossRefGoogle Scholar
16Vick, D., Friedrich, L.J., Dew, S.K., Brett, M.J., Robbie, K., Seto, M.Smy, T.: Self-shadowing and surface diffusion effects in obliquely deposited thin films. Thin Solid Films 339, 88 1999CrossRefGoogle Scholar
17Gaskell, D.R.: Introduction to the Thermodynamics of Materials, 3rd ed.Taylor & Francis Washington 1995 356Google Scholar
18Li, C-C., Huang, J-L., Lin, R-J., Chen, C-H.Lii, D-F.: Characterization of activated non-evaporable porous Ti and Ti–Zr–V getter films by synchrotron radiation photoemission spectroscopy. Thin Solid Films 515, 1121 2006CrossRefGoogle Scholar
19Ellingham, J.T.: Reducibility of oxides and sulfides in metallurgical processes. J. Soc. Chem. Ind. 63, 125 1944Google Scholar