Hostname: page-component-586b7cd67f-2plfb Total loading time: 0 Render date: 2024-11-27T04:30:52.077Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical and wear properties of Si3N4–W composites using tungsten boride powder

Published online by Cambridge University Press:  31 January 2011

Hideki Hyuga ,
Mark I. Jones ,
Kiyoshi Hirao  and
Yukihiko Yamauchi
Hideki Hyuga
Affiliation:
Fine Ceramics Research Association, 2268–1 Shimo-shidami, Nagoya 463–8687, Japan
Mark I. Jones
Affiliation:
Synergy Materials Research Center, National Institute of Advanced Industrial Science and Technology (AIST), 2268–1 Shimo-shidami, Nagoya 463–8687, Japan
Kiyoshi Hirao
Affiliation:
Synergy Materials Research Center, National Institute of Advanced Industrial Science and Technology (AIST), 2268–1 Shimo-shidami, Nagoya 463–8687, Japan
Yukihiko Yamauchi
Affiliation:
Synergy Materials Research Center, National Institute of Advanced Industrial Science and Technology (AIST), 2268–1 Shimo-shidami, Nagoya 463–8687, Japan
Get access

Abstract

Silicon nitride–tungsten (Si3N4–W) composites were fabricated by reduction of tungsten boride under hot-press sintering in a nitrogen atmosphere. The fabricated composite consisted of mainly β–Si3N4 and W. The Si3N4 matrix grains were composed of an elongated and bimodal structure similar to conventional Si3N4. The mechanical properties of the composites in terms of fracture toughness and strength were almost the same as those of a monolithic Si3N4 produced under the same sintering conditions. The sliding wear properties of the composites were evaluated using a ball-on-disk machine under unlubricated sliding conditions against a commercial Si3N4 ceramic ball. The tungsten (W) content had a significant effect on the composite wear properties. In particular, for a composite disk with a W content of 8 vol% the specific wear rate of the opposing ball was decreased around ten times compared to the monolithic Si3N4. The composites had higher wear resistance compared with the conventional silicon nitride, which was attributed to the formation of debris consisting of W, Si, and O. The debris restricted the adhesion of the two surfaces.

Type
Articles
Information
Journal of Materials Research , Volume 18 , Issue 9 , September 2003 , pp. 2262 - 2267
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Kitamura, K., Takebayashi, H., SAE Paper, No. 972774 (1997).Google Scholar
2.Andersson, P. and Holmberg, K., Wear 175, 1 (1994).Google Scholar
3.Kita, H., Kawamura, H., Unno, Y., and Sekiyama, S., SAE Paper No. 950981 (1995).Google Scholar
4.Andersson, P. and Holmberg, K., Wear 175, 1 (1994).CrossRefGoogle Scholar
5.Hyuga, H., Hirao, K., Yamauchi, Y., and Kanzaki, S., Ceram. Eng. Sci. Proc. 22, 197 (2001).Google Scholar
6.Iizuka, T., Murao, T., Yamamoto, H., and Kita, H., J. Ceram. Soc. Jpn. 109, 699 (2001).Google Scholar
7.Skopp, A. and Woydt, M., Tribo. Int. 25, 61 (1992).Google Scholar
8.Liu, H.W. and Xue, Q., Wear 198, 143 (1996).Google Scholar
9. I. Allam, M., J. Mater. Sci. 26, 3977 (1991).CrossRefGoogle Scholar
10.Hyuga, H., Hayashi, Y., Sekino, T., and Niihara, K., Nanostruct. Mater. 9, 547 (1997).Google Scholar
11.Oh, S.T., Sando, M., Sekino, T., and Niihara, K., Nanostruct. Mater. 10, 267 (1998).Google Scholar
12.Sekino, T. and Niihara, K., J. Mater. Sci. 32, 3943 (1997).CrossRefGoogle Scholar
13.Lawn, B.R., Evans, A.G., and Marshall, D.B., J. Am. Ceram. Soc. 63, 574 (1980).CrossRefGoogle Scholar
14.Krell, A. and Klaffke, D., J. Am. Ceram. Soc. 79, 1139 (1996).CrossRefGoogle Scholar
15.Adachi, K., Kato, K., and Chen, N., Wear 203–204, 291 (1997).Google Scholar
16.Gnesin, G.G., Powder Metall. Metal Ceram. 32, 381 (1993).Google Scholar
17.Fischer, T.E. and Tomizawa, H., Wear 105, 29 (1985).CrossRefGoogle Scholar
18.Kim, S.S., Kim, S.W., and Hsu, S.M., Wear 179, 69 (1994).CrossRefGoogle Scholar
19.Takadoum, J., Bennani, H.H., and Mairey, D., J. Eur. Ceram. Soc. 18, 553 (1998).CrossRefGoogle Scholar