Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-27T07:44:01.175Z Has data issue: false hasContentIssue false
  • English
  • Français

Joining of AlN to Cu Using In-base Active Brazing Fillers

Published online by Cambridge University Press:  31 January 2011

Dae Huh  and
Dae-Hun Kim
Dae Huh
Affiliation:
Metallurgy Division, Chungnam Regional Industrial Technology Institute, 22–4 Gayang-2 dong, Daejeon, Korea 300–092
Dae-Hun Kim*
Affiliation:
Joining Research Group, Korea Institute of Machinery and Materials (KIMM), P.O. Box 101, Yusung, Daejeon, Korea 305–600
*
a)Address all correspondence to this author.
Get access

Abstract

Brazing of aluminum nitride (AlN), which is a good ceramic substrate in high power electronic applications, to copper was investigated using In-base active fillers. Compositions of brazing fillers were chosen as In–1 wt.% Ti (IT1), In–19 wt.% Ag–2 wt.% Ti (IAT2), In–15 wt.% Ti (IT15), and In–52 wt.% Ag–20 wt.% Cu–3 wt.% Ti (ACIT3). Brazing operation was performed in vacuum at temperatures of 650–900 °C. The brazing fillers showed good wetting on AlN and led to a strong bond between AlN and braze alloy. From the microstructural analysis, no evidence of reaction layer was clearly found at the interface under the experimental brazing conditions. The composition of brazing alloy layer changed into Cu9In4 phase due to the extensive dissolving of Cu from base metal. Bond strength, measured by 4-point bend test, was obtained as high as 23–30 kgf for the Cu/AlN/Cu joint brazed with IT15 and ACIT3 fillers, and shown to be nearly constant even when the temperature was varied within 700–800 °C. Most of the fracture appeared to proceed through the interior of the AlN ceramic. Based on the experimental results, it is believed that a strong bonding between AlN and braze alloy can be achieved without the apparent forming of a Ti-rich reaction layer at the interface.

Type
Articles
Information
Journal of Materials Research , Volume 12 , Issue 4 , April 1997 , pp. 1048 - 1055
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Werdecker, W. and Adlinger, F., Aluminum nitride–An Alternative Ceramic Substrate for High Power Applications in Microcircuit, in Proc. 34th ECC (IEEE, New York, 1984), p. 420.Google Scholar
2.Iwase, N., Tsuge, A., and Sugiura, Y., Development of a High Thermal Conductive AlN Ceramic Substrate Technology, in Proc. 3rd IMC, Tokyo (1984), p. 180.Google Scholar
3.Carim, A. H. and Loehman, R. E., J. Mater. Res. 5, 1520 (1990).CrossRefGoogle Scholar
4.Nakao, Y., Nishimoto, K., and Saida, K., ISIJ Int. 30 (12), 1142 (1990).CrossRefGoogle Scholar
5.Kuzumaki, T., Ariga, T., and Miyamoto, Y., ISIJ Int. 30 (12), 1135 (1990).CrossRefGoogle Scholar
6.Huh, D., Ph.D.Thesis, Chungnam University, Daejeon, Korea (1992).Google Scholar
7.Nakahashi, M., Shirokane, M., and Takeda, H., J. Jpn. Inst. Metals 53 (11), 1153 (1989).CrossRefGoogle Scholar
8.Watanabe, T., Sumiki, S., and Yanagisawa, A., J. High Temp. Soc. 20 (2), 126 (1993).Google Scholar
9.Hansen, M. H., Constitution of Binary Alloys, first supplement by R. Elliott, second supplement by F. A. Shunk (McGraw-Hill, New York, 1958).CrossRefGoogle Scholar
10.Mizuhara, H. and Huebel, E., Welding J. 60 (10), 43 (1986).Google Scholar
11.Nicholas, M. G., Valentine, T. M., and Waite, M. J., J. Mater. Sci. 15, 2197 (1980).CrossRefGoogle Scholar
12.Kurkjian, C. R. and Kingrey, W. D., J. Phys. Chem. 60 (7), 961 (1956).CrossRefGoogle Scholar
13.Takashio, H., Bull. Jpn. Inst. Metals 24 (2), 113 (1985).CrossRefGoogle Scholar
14.Mader, W. and Rühle, M., Acta Metall. 37 (3), 853 (1989).CrossRefGoogle Scholar
15.King, B. W., Trip, H. P., and Duckworth, W. H., J. Am. Ceram. Soc. 42 (11), 504 (1959).CrossRefGoogle Scholar