Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-25T03:24:07.155Z Has data issue: false hasContentIssue false
  • English
  • Français

Formation of Al2O3 during heating of an Al/TiO2 nanocomposite powder

Published online by Cambridge University Press:  03 March 2011

D.L. Zhang ,
D.Y. Ying  and
P. Munroe
D.L. Zhang*
Affiliation:
Waikato Centre for Advanced Materials, Department of Materials and Process Engineering, University of Waikato, Hamilton 2001, New Zealand
D.Y. Ying
Affiliation:
Bioengineering Technologies Team, HortResearch, Ruakura Research Centre, Hamilton 2001, New Zealand
P. Munroe
Affiliation:
Electron Microscope Unit, University of New South Wales, Sydney 2052, Australia
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The solid-state reactions between Al and TiO2 that occur during heating an Al/TiO2 nanocomposite powder produced using high-energy mechanical milling have been studied using thermal analysis, x-ray diffractometry (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) in combination with compositional microanalysis. It has been found that Al and TiO2 react in the temperature range from 650 to 800 °C, forming Al3Ti, but XRD analysis, SEM examination, and detailed TEM characterization of the powder particles heated to 800 °C show that the expected Al2O3 does not form. However, α–Al2O3 particles form during heating from 800 to 1000 °C. The possible reasons for the time gap between formation of Al3Ti and Al2O3 are discussed.

Keywords

Chemical reactionCompositePowder processing
Type
Articles
Information
Journal of Materials Research , Volume 20 , Issue 2 , February 2005 , pp. 307 - 313
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Maity, P.C., Chakraborty, P.N. and Panigrahi, S.C.: Processing and properties of Al-Al2O3 (TiO2) in situ particle composite. J. Mater. Process. Technol. 53, 857 (1995).CrossRefGoogle Scholar
2.Feng, C.F. and Froyen, L.: Formation of Al3Ti and Al2O3 from an Al-TiO2 system for preparing in-situ aluminium matrix composites. Composites Part A 31, 385 (2000).CrossRefGoogle Scholar
3.Barlow, I.C., Jones, H. and Rainforth, W.M.: The effect of heat treatment at 500-655 °C on the microstructure and properties of mechanically alloyed Al-Ti-O based material. Mater. Sci. Eng. A 351, 344 (2003).CrossRefGoogle Scholar
4.Barlow, I.C., Jones, H. and Rainforth, W.M.: Evolution of microstructure and hardening, and the role of Al3Ti coarsening, during extended thermal treatment in mechanically alloyed Al-Ti-O based materials. Acta Mater. 49, 1209 (2001).CrossRefGoogle Scholar
5.Peng, H.X., Wang, D.Z., Geng, L., Yao, C.K., F, J. and Mao, : Evaluation of the microstructure of in-situ reaction processed Al3Ti-Al2O3-Al composite. Scripta Mater. 37, 199 (1997).CrossRefGoogle Scholar
6.Pan, J., Yang, D.M., Li, J.H., Ning, X.G., Ye, H.Q., Fukunaga, H. and Yao, Z.K.: Microstructural study of the interface reaction between titania whiskers and aluminium. Compos. Sci. Technol. 57, 319 (1997).CrossRefGoogle Scholar
7.Tsuchitori, I. and Fukunaga, H.: Effect of impurity elements on reaction of reinforcement with matrix in rutile type titanium oxide/aluminium composites. J. Jpn. Inst. Met. 59, 1306 (1995).CrossRefGoogle Scholar
8.Tsuchitori, I., Sasaki, G. and Fukunaga, H.: Enhanced solid state reaction of TiO2/Al composites by doping. J. Jpn. Inst. Met. 61, 544 (1997).CrossRefGoogle Scholar
9.Claussen, N., Garcia, D.E. and Janssen, R.: Reaction sintering of alumina-aluminide alloys (3A). J. Mater. Res. 11, 2884 (1996).CrossRefGoogle Scholar
10.Schicker, S., Garcia, D.E., Bruhn, J., Janssen, R. and Claussen, N.: Reaction synthesized Al2O3-based intermetallic composites. Acta Mater. 46, 2485 (1998).CrossRefGoogle Scholar
11.Welham, N.J.: Mechanical activation of the solid-state reaction between Al and TiO2. Mater. Sci. Eng. A 255, 81 (1998).CrossRefGoogle Scholar
12.Zhang, D.L. and Newby, M.: Titanium alloy based dispersion-strengthened composites, U.S. Patent No. US6 264 719 B1, 1999.Google Scholar
13.Zhang, D.L., Ying, D.Y. and Adam, G.: Reaction kinetics and microstructural evolution during heating high-energy ball milled Al-metal oxide composite powders. J. Metastable Nanocrystalline Mater. 13, 287 (2002).CrossRefGoogle Scholar
14.Zhang, D.L., Cai, Z.H. and Newby, M.: Low cost Ti(Al,O)/Al2O3 and TixAly/Al2O3 composites. Mater. Tech. Adv. Performance Mater. 18, 94 (2003).Google Scholar
15.Ying, D.Y., Zhang, D.L. and Newby, M.: Solid state reactions during heating mechanically milled Al/TiO2 composite powders. Metall. Mater. Trans. A 35A, 2115 (2004).CrossRefGoogle Scholar
16.Lefebvre, W., Loiseau, A., Thomas, M. and Menand, A.: Influence of oxygen on the α→γ massive transformation in a Ti-48at.%Al alloy. Philos. Mag. A 82, 2341 (2002).Google Scholar
17.Fan, G.J., Quan, M.X. and Hu, Z.Q.: Supersaturated Al(Ti) solid solutions with partial L12 ordering prepared by mechanical alloying. Scripta Metall. Mater. 33, 377 (1995).CrossRefGoogle Scholar
18.Oehring, M., Klassen, T. and Bormann, R.: The formation of metastable Ti-Al solid solution by mechanical alloying and ball milling. J. Mater. Res. 8, 2819 (1993).CrossRefGoogle Scholar