Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-26T15:09:23.982Z Has data issue: false hasContentIssue false

Evaluation of wire electro discharge machining characteristics of Ti50Ni50−xCux shape memory alloys

Published online by Cambridge University Press:  18 May 2016

Mallaiah Manjaiah*
Affiliation:
Department of Mechanical Engineering Science, University of Johannesburg, Kingsway Campus, Johannesburg-2006, South Africa
Rudolph Frans Laubscher
Affiliation:
Department of Mechanical Engineering Science, University of Johannesburg, Kingsway Campus, Johannesburg-2006, South Africa
Sannayellapa Narendranath
Affiliation:
Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal-575025, India
Sathyappa Basavarajappa
Affiliation:
Department of Studies in Mechanical Engineering, University B.D.T. College of Engineering, Davangere-577004, Karnataka, India
Vinayak Neelakanth Gaitonde
Affiliation:
Department of Industrial and Production Engineering, B. V. B. College of Engineering and Technology, Hubli-580031, Karnataka, India
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The machining of shape memory alloys (SMAs) is fairly essential and integral part in the manufacture of components for utilizing in engineering applications. An effort has been made in the present work to study the effect of wire electro discharge machining process parameters such as pulse on time (Ton), pulse off time (Toff) and servo voltage (SV) have been analyzed on material removal rate and surface roughness. The investigation clearly reveals that an increased pulse on time with decrease in pulse off time as well as SV increases the amount of material removed in machining of SMAs. On the other hand, the surface roughness increases with increased pulse on time and decreases with increased pulse off time as well as SV. The surface topography of the machined surface was analyzed using scanning electron microscope (SEM) and confocal micrographs. Phase changes on the machined surface with respect to pulse on time and SV were evaluated from X-ray diffractometer (XRD) analysis.

Type
Articles
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Terayama, A. and Kyogoku, H.: Shape memory characteristics of the P/M-processed Ti–Ni–Cu alloys. Mater. Sci. Eng., A 527, 5484 (2010).Google Scholar
Valeanu, M., Lucaci, M., Crisan, A.D., Sofronie, M., Leonat, L., and Kuncser, V.: Martensitic transformation of Ti50Ni30Cu20 alloy prepared by powder metallurgy. J. Alloys Compd. 509, 495 (2011).Google Scholar
Frenzel, J., George, E.P., Dlouhy, A., Somsen, C., Wagner, M.F., and Eggeler, G.: Influence of Ni on martensitic phase transformations in NiTi shape memory alloys. Acta Mater. 58, 3444 (2010).Google Scholar
Weinert, K. and Petzoldt, V.: Machining of NiTi based shape memory alloys. Mater. Sci. Eng., A 378, 180 (2004).Google Scholar
Weinert, K., Petzoldt, V., and Kotter, D.: Turning and drilling of NiTi shape memory alloys. CIRP Ann. Technol. 53, 65 (2004).CrossRefGoogle Scholar
Kaynak, Y., Karaca, H.E., Noebe, R.D., and Jawahir, I.S.: Analysis of tool-wear and cutting force components in dry, preheated, and cryogenic machining of NiTi shape memory alloys. Procedia CIRP 8, 498 (2013).Google Scholar
Chen, S.L., Hsieh, S.F., Lin, H.C., Lin, M.H., and Huang, J.S.: Electrical discharge machining of TiNiCr and TiNiZr ternary shape memory alloys. Mater. Sci. Eng., A 446, 486 (2007).Google Scholar
Lin, H., Lin, K., Chen, Y., and Chu, C.: The wire electro-discharge machining characteristics of Fe–30Mn–6Si and Fe–30Mn–6Si–5Cr shape memory alloys. J. Mater. Process. Technol. 161, 435 (2005).Google Scholar
Hsieh, S.F., Chen, S.L., Lin, H.C., Lin, M.H., and Chiou, S.Y.: The machining characteristics and shape recovery ability of Ti–Ni–X (X = Zr, Cr) ternary shape memory alloys using the wire electro-discharge machining. Int. J. Mach. Tools Manufact. 49, 509 (2009).Google Scholar
Narendranath, S., Manjaiah, M., Basavarajappa, S., and Gaitonde, V.: Experimental investigations on performance characteristics in wire electro discharge machining of Ti50Ni42.4Cu7.6 shape memory alloy. Proc. Inst. Mech. Eng., Part B 227, 1180 (2013).Google Scholar
Manjaiah, M., Narendranath, S., and Gaitonde, S.B.V.N.: Some investigations on wire electric discharge machining characteristics of titanium nickel shape memory alloy. Trans. Nonferrous Met. Soc. China 24, 3201 (2014).Google Scholar
Manjaiah, M., Narendranath, S., Basavarajappa, S., and Gaitonde, V.N.: Effect of electrode material in wire electro discharge machining characteristics of Ti50Ni50−xCux shape memory alloy. Precis. Eng. 41, 68 (2015).Google Scholar
Ross, P.J.: Taguchi Techniques for Quality Engineering, Illustrate (McGraw Hill Professional, New York, NY, 1996).Google Scholar
Garg, M.P., Jain, A., and Bhushan, G.: Modelling and multi-objective optimization of process parameters of wire electrical discharge machining using non-dominated sorting genetic algorithm-II. Proc. Inst. Mech. Eng., Part B 226, 1986 (2012).Google Scholar
Tarng, Y.S. and Chung, L.K.: Determination of optimal cutting parameters in wire electrical discharge machining. Int. J. Mach. Tools Manufact. 35, 1693 (1995).CrossRefGoogle Scholar
Alidoosti, A., Ghafari-Nazari, A., Moztarzadeh, F., Jalali, N., Moztarzadeh, S., and Mozafari, M.: Electrical discharge machining characteristics of nickel–titanium shape memory alloy based on full factorial design. J. Intell. Mater. Syst. Struct. 24, 1546 (2013).CrossRefGoogle Scholar
Kuriakose, S. and Shunmugam, M.S.: Characteristics of wire-electro discharge machined Ti6Al4V surface. Mater. Lett. 58, 2231 (2004).Google Scholar