Hostname: page-component-586b7cd67f-tf8b9 Total loading time: 0 Render date: 2024-11-23T14:07:49.189Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of unloading strain rate on the elastic modulus of a viscoelastic solid determined by nanoindentation

Published online by Cambridge University Press:  01 March 2006

Naoki Fujisawa  and
Michael V. Swain
Naoki Fujisawa*
Affiliation:
School of Aerospace, Mechanical & Mechatronic Engineering, University of Sydney, Sydney NSW 2006, Australia
Michael V. Swain
Affiliation:
Biomaterials Unit, Department of Oral Sciences, School of Dentistry, University of Otago, Duniden, New Zealand; Biomaterials Science Research Unit, Faculty of Dentistry, University of Sydney, United Dental Hospital, Surry Hills NSW 2010, Australia; and School of Aerospace, Mechanical & Mechatronic Engineering, University of Sydney, Sydney NSW 2006, Australia
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The elastic modulus of an amorphous polymer was investigated by nanoindentation using combinations of ten total penetration depths and three constant unload rates. This experimental design provided a range of unloading strain rates coexisting with a range of depths. The elastic modulus of the material was found to correlate strongly with the unloading strain rate, whereas its correlation with the indentation depth was statistically nonsignificant. Thus, the increase of elastic modulus that occurred with decreasing depth at each constant unload rate was merely due to the increasing unloading strain rate associated with the decreasing depth. The true depth dependence of a rate-dependent material can therefore be studied only by maintaining a constant unloading strain rate across the entire depth range. The implications of these results to the continuous stiffness measurement technique are considered.

Keywords

Elastic propertiesPolymer
Type
Articles
Information
Journal of Materials Research , Volume 21 , Issue 3 , March 2006 , pp. 708 - 714
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Oliver, W.C., Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
2.Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).CrossRefGoogle Scholar
3.Oliver, W.C., Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 (2004).CrossRefGoogle Scholar
4.Bolshakov, A., Pharr, G.M.: Influences of pileup on the measurement of mechanical properties by load and depth-sensing indentation techniques. J. Mater. Res. 13, 1049 (1998).CrossRefGoogle Scholar
5.Bec, S., Tonck, A., Georges, J-M., Georges, E., Loubet, J.L.: Improvements in the indentation method with a surface force apparatus. Philos. Mag. A 74, 1061 (1996).CrossRefGoogle Scholar
6.Hochstetter, G., Jimenez, A., Cano, J.P., Felder, E.: An attempt to determine the true stress-strain curves of amorphous polymers by nanoindentation. Tribol. Int. 36, 973 (2003).CrossRefGoogle Scholar
7.Feng, G., Ngan, A.H.W.: Effects of creep and thermal drift on modulus measurement using depth-sensing indentation. J. Mater. Res. 17, 660 (2002).CrossRefGoogle Scholar
8.Ngan, A.H.W., Wang, H.T., Tang, B., Sze, K.Y.: Correcting power-law viscoelastic effects in elastic modulus measurement using depth-sensing indentation. Int. J. Solids Struct. 42, 1831 (2005).CrossRefGoogle Scholar
9.Tang, B., Ngan, A.H.W.: Accurate measurement of tip-sample contact side during nanoindentation of viscoelastic materials. J. Mater. Res. 18, 1141 (2003).CrossRefGoogle Scholar
10.Berthoud, P., G’Sell, C., Hiver, J.M.: Elastic-plastic indentation creep of glassy poly(methyl methacrylate) and polystyrene: Characterization using uniaxial compression and indentation tests. J. Phys. D: Appl. Phys. 32, 2923 (1999).CrossRefGoogle Scholar
11.Menčík, J., Rauchs, G., Bardon, J., Riche, A.: Determination of elastic modulus and hardness of viscoelastic-plastic materials by instrumented indentation under harmonic load. J. Mater. Res. 20, 2660 (2005).CrossRefGoogle Scholar
12.Suganuma, M., Swain, M.V.: Simple method and critical comparison of frame compliance and indenter area function for nanoindentation. J. Mater. Res. 19, 3490 (2004).CrossRefGoogle Scholar
13.Briscoe, B.J., Fiori, L., Pelillo, E.: Nano-indentation of polymeric surfaces. J. Phys. D: Appl. Phys. 31, 2395 (1998).CrossRefGoogle Scholar
14.White, C.C., Vanlandingham, M.R., Drzal, P.L., Chang, N-K., Chang, S-H.: Viscoelastic characterization of polymers using instrumented indentation. II. Dynamic testing. J. Polym. Sci., Part B: Polym. Phys. 43, 1812 (2005).CrossRefGoogle Scholar
15.Armitage, P., Berry, G.: Statistical Methods in Medical Research (Blackwell Scientific Publication, Oxford, UK, 1987), pp. 297–305.Google Scholar