Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-20T07:14:34.306Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of microstructure on damage tolerance in grinding dental glass-ceramics

Published online by Cambridge University Press:  31 January 2011

Hockin H. K. Xu  and
Said Jahanmir
Hockin H. K. Xu
Affiliation:
Paffenbarger Research Center, American Dental Association Health Foundation, National Institute of Standards and Technology, Gaithersburg, Maryland 20899
Said Jahanmir
Affiliation:
Ceramics Division, National Institute of Standards and Technology, Gaithersburg, Maryland 20899
Get access

Abstract

This study investigated the modes of grinding-induced subsurface damage in dental glass-ceramics and the influence of microstructure on strength degradation. A series of micaceous glass-ceramics crystallized from the same glass composition were tested. The diameter of the mica platelets in these glass-ceramics was varied via heat treatment. Grinding was performed using three diamond wheels (with diamond particle size of 40, 100, and 180 µm, respectively) at depth of cut ranging from 5 µm to 100 µm. A bonded- interface technique was employed to examine the machining- induced subsurface damage. Relatively large median and lateral cracks were found in the glass-ceramic with the smallest mica platelets. In contrast, no cracks were found in the material containing large mica platelets. The ground specimens were fractured in four-point flexure to measure strength as a function of grinding conditions and mica platelet sizes. The strength of the ground specimens was reduced to approximately 30% of the strength of the polished specimens for the glass- ceramic containing the smallest mica platelets; that of the glass-ceramic with the intermediate mica platelet size was reduced to 60%. In contrast, virtually no strength loss occurred with the glass-ceramic containing large mica platelets. Microstructure was shown to determine the mode and degree of strength-controlling damage in the machining of these dental glass-ceramics. Polishing after grinding removes subsurface damage and recovers strength for the glass-ceramics containing fine mica crystals.

Type
Articles
Information
Journal of Materials Research , Volume 13 , Issue 8 , August 1998 , pp. 2231 - 2236
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Adair, P. J. and Grossman, D. G., Int. J. Periodont. Rest. Dent. 2, 32 (1984).Google Scholar
2.Beall, G. H., U.S. Patent No. 4,608,348 (1986).Google Scholar
3.Grossman, D. G. and Johnson, J. L. M., U.S. Patent No. 4,652,312 (1987).Google Scholar
4.Beall, G. H., J. Non-Cryst. Solids 129, 163 (1991).CrossRefGoogle Scholar
5.Beall, G. H., Annu. Rev. Mater. Sci. 22, 91 (1992).CrossRefGoogle Scholar
6.Chyung, C. K., Beall, G. H., and Grossman, D. G., in Electron Microscopy and Structure of Materials, edited by Thomas, G., Fulrath, R. M., and Fisher, R. M. (University of California Press, Berkeley, CA, 1972), p. 1167.CrossRefGoogle Scholar
7.Sturdevant, C. M., Operative Dentistry (Mosby, Baltimore, MD, 1995).Google Scholar
8.Rosenstiel, S. F., Land, M. F., and Fujimoto, J., Contemporary Fixed Prosthodontics (Mosby, Baltimore, MD, 1995).Google Scholar
9.Rekow, E. D., J. Am. Dent. Assoc. 122, 42 (1991).CrossRefGoogle Scholar
10.Xu, H. H. K. and Jahanmir, S., Ceram. Eng. Sci. Proc. 16 (1), 295 (1995).CrossRefGoogle Scholar
11.Xu, H. H. K., Padture, N. P., and Jahanmir, S., J. Am. Ceram. Soc. 78 (9), 2443 (1995).CrossRefGoogle Scholar
12.Xu, H. H. K., Jahanmir, S., and Ives, L. K., J. Mater. Res. 11, 1717 (1996).CrossRefGoogle Scholar
13.Grossman, D. G., in Proceedings of the International Symposium on Computer Restorations: The State of the Art of the Cerec-Method, edited by Mormann, W. H. (Quintessenz Verlags-GmbH, Berlin, Germany, 1991), pp. 103–115.Google Scholar
14.Kelly, J. R., Luthy, H., Gougoulakis, A., Pober, R. L., and Mormann, W. H., in Proceedings of the International Symposium on Computer Restorations: The State of the Art of the Cerec-Method, edited by Mormann, W. H. (Quintessenz Verlags-GmbH, Berlin, Germany, 1991), pp. 253–273.Google Scholar
15.Luthy, H., Besek, M., and Mormann, W. H., in Proceedings of the International Symposium on Computer Restorations: The State of the Art of the Cerec-Method, edited by Mormann, W. H. (Quintessenz Verlags-GmbH, Berlin, Germany, 1991), pp. 613–622.Google Scholar
16.Fischer-Cripps, A. C. and Lawn, B. R., Acta Metall. 44 (2), 519 (1996).Google Scholar
17.Peterson, I. M., Pajares, A., Lawn, B. R., Thompson, V. P., and Rekow, E. D., J. Dent. Res. 77 (4), 589 (1998).CrossRefGoogle Scholar
18.Xu, H. H. K., Smith, D. T., and Jahanmir, S., J. Mater. Res. 11, 2325 (1996).CrossRefGoogle Scholar
19.Xu, H. H. K. and Jahanmir, S., J. Am Ceram. Soc. 77 (5), 1388 (1994).CrossRefGoogle Scholar
20.Lawn, B. R., Fracture of Brittle Solids–Second Edition (Cambridge University Press, Cambridge, U.K., 1993), Chaps. 7–9.CrossRefGoogle Scholar