Hostname: page-component-cd9895bd7-hc48f Total loading time: 0 Render date: 2024-12-23T11:26:27.442Z Has data issue: false hasContentIssue false
  • English
  • Français

Beam speed effects on Ti–6Al–4V microstructures in electron beam additive manufacturing

Published online by Cambridge University Press:  13 August 2014

Xibing Gong ,
James Lydon ,
Kenneth Cooper  and
Kevin Chou
Xibing Gong
Affiliation:
Department of Mechanical Engineering, The University of Alabama, Tuscaloosa, Alabama 35487, USA
James Lydon
Affiliation:
Advanced Manufacturing Technology Team, Marshall Space Flight Center, Huntsville, Alabama 35812, USA
Kenneth Cooper
Affiliation:
Advanced Manufacturing Technology Team, Marshall Space Flight Center, Huntsville, Alabama 35812, USA
Kevin Chou*
Affiliation:
Department of Mechanical Engineering, The University of Alabama, Tuscaloosa, Alabama 35487, USA
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The effect of the beam scanning speed on part microstructures in the powder-bed electron beam additive manufacturing (EBAM) process was investigated in this research. Four levels of the beam speed were tested in building EBAM Ti–6Al–4V samples. The samples were subsequently used to prepare metallographic specimens for observations by optical microscopy and scanning electron microscopy. During the experiment, a near-infrared thermal imager was also used to acquire build surface temperatures for melt tool size estimates. It was found that the X-plane (side surface) shows columnar prior β grains, with the width in the range of about 40–110 µm, and martensitic structures. The width of columnar grains decreases with the increase of the scanning speed. In addition, the Z-plane (scanning surface) shows equiaxed grains, in the range of 50–85 µm. The grain size from the lowest beam speed (214 mm/s) is much larger compared to other samples of higher beam speeds (e.g., 376–689 mm/s). In addition, increasing the beam scanning speed will also result in finer α-lath. However, the porosity defect on the build surface also becomes severe at the highest scanning speed (689 mm/s).

Type
Articles
Information
Journal of Materials Research , Volume 29 , Issue 17: Focus Issue: The Materials Science of Additive Manufacturing , 14 September 2014 , pp. 1951 - 1959
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Murr, L.E., Esquivel, E.V., Quinones, S.A., Gaytan, S.M., Lopez, M.I., Martinez, E.Y., Medina, F., Hernandez, D.H., Martinez, E., Martinez, J.L., Stafford, S.W., Brown, D.K., Hoppe, T., Meyers, W., Lindhe, U., and Wicker, R.B.: Microstructures and mechanical properties of electron beam-rapid manufactured Ti-6Al-4V biomedical prototypes compared to wrought Ti-6Al-4V. Mater. Charact. 60, 96 (2009).CrossRefGoogle Scholar
Gong, X. and Chou, K.: Characterizations of sintered Ti-6Al-4V powders in electron beam additive manufacturing. Proceedings of the ASME International Manufacturing Science and Engineering Conference, Mears, L. ed.; ASME, Madison, WI, 2013; p. V001T01A0022013.Google Scholar
Zäh, M.F. and Lutzmann, S.: Modelling and simulation of electron beam melting. Prod. Eng. 4, 15 (2010).Google Scholar
Shen, N. and Chou, K.: Thermal modeling of electron beam additive manufacturing process: Powder sintering effect. Proceedings of the ASME International Manufacturing Science and Engineering Conference, Schmid, S.R., Greenslet, H.Y., and Mears, L. ed.; ASME, Notre Dame, IN, 2012; p. 287.Google Scholar
Gong, X., Cheng, B., Price, S., and Chou, K.: Powder-bed electron-beam-melting additive manufacturing: Powder characterization, process simulation and metrology. Early Career Technical Conference, Durbetaki, P. and Donnell, J. ed.; ASME, Birmingham, AL, 2013; p. 59.Google Scholar
Price, S., Cooper, K., and Chou, K.: Evaluations of temperature measurements by near-infrared thermography in powder-based electron-beam additive manufacturing. Proceedings of the Solid Freeform Fabrication Symposium, Bourell, D., Crawford, R.H., Seepersad, C.C., Beaman, J.J., and Marcus, H.L. ed.; University of Texas, Austin, TX, 2012; p. 761.Google Scholar
Koike, M., Martinez, K., Guo, L., Chahine, G., Kovacevic, R., and Okabe, T.: Evaluation of titanium alloy fabricated using electron beam melting system for dental applications. J. Mater. Process. Technol. 211, 1400 (2011).Google Scholar
Cooke, A.L. and Soons, J.A.: Variability in the geometric accuracy of additively manufactured test parts. Proceedings of the Solid Freeform Fabrication Symposium, Bourell, D. ed.; University of Texas, Austin, TX, 2010; pp. 1.Google Scholar
Al-Bermani, S.S., Blackmore, M.L., Zhang, W., and Todd, I.: The origin of microstructural diversity, texture, and mechanical properties in electron beam melted Ti-6Al-4V. Metall. Mater. Trans. A 41A, 3422 (2010).Google Scholar
Safdar, A., Wei, L.Y., Snis, A., and Lai, Z.: Evaluation of microstructural development in electron beam melted Ti-6Al-4V. Mater. Charact. 65, 8 (2012).Google Scholar
Antonysamy, A.A., Meyer, J., and Prangnell, P.B.: Effect of build geometry on the β-grain structure and texture in additive manufacture of Ti6Al4V by selective electron beam melting. Mater. Charact. 84, 153 (2013).Google Scholar
Facchini, L., Magalini, E., Robotti, P., and Molinari, A.: Microstructure and mechanical properties of Ti-6Al-4V produced by electron beam melting of pre-alloyed powders. Rapid Prototyping J. 15, 171 (2009).Google Scholar
Christensen, A., Kircher, R., and Lippincott, A.: Qualification of electron beam melted (EBM) Ti6Al4V-ELI for orthopaedic applications. Proceedings of the Materials Processes for Medical Devices Conference, Gilbert, J. ed.; ASM International, Palm Desert, CA, 2007; pp. 48.Google Scholar
Murr, L.E., Gaytan, S.M., Medina, F., Martinez, E., Martinez, J.L., Hernandez, D.H., Machado, B.I., Ramirez, D.A., and Wicker, R.B.: Characterization of Ti-6Al-4V open cellular foams fabricated by additive manufacturing using electron beam melting. Mater. Sci. Eng., A 527, 1861–1868 (2010).Google Scholar
Gong, X., Anderson, T., and Chou, K.: Review on powder-based electron beam additive manufacturing technology. In International Symposium on Flexible Automation, Leu, M. ed.; ASME, St. Louis, MO, 2012; p. 507.Google Scholar
Murr, L.E., Gaytan, S.M., Medina, F., Martinez, E., Hernandez, D.H., Martinez, L., Lopez, M.I., Wicker, R.B., and Collins, S.: Effect of build parameters and build geometries on residual microstructures and mechanical properties of Ti-6Al-4V components built by electron beam melting (EBM). Proceedings of the Solid Freeform Fabrication Symposium, Bourell, D. ed.; University of Texas, Austin, TX, 2009; p. 374.Google Scholar
Bontha, S., Klingbeil, N.W., Kobryn, P.A., and Fraser, H.L.: Effects of process variables and size-scale on solidification microstructure in beam-based fabrication of bulky 3D structures. Mater. Sci. Eng., A 513–514, 311 (2009).Google Scholar
Murr, L.E., Quinones, S.A., Gaytan, S.M., Lopez, M.I., Rodela, A., Martinez, E.Y., Hernandez, D.H., Martinez, E., Medina, F., and Wicker, R.B.: Microstructure and mechanical behavior of Ti-6Al-4V produced by rapid-layer manufacturing, for biomedical applications. J. Mech. Behav. Biomed. Mater. 2, 20 (2009).Google Scholar
Jamshidinia, M., Kong, F., and Kovacevic, R.: The coupled CFD-FEM model of electron beam melting (EBM). Proceedings of the Early Career Technical Conference (ECTC), Durbetaki, P. and Donnell, J. ed.; ASME, Birmingham, AL, 2013; p. 163.Google Scholar
Mahale, T.R.: Electron beam melting of advanced materials and structures. Ph.D. Dissertation, North Carolina State University, Raleigh, NC, 2009.Google Scholar
Wang, K., Zeng, W., Shao, Y., Zhao, Y., and Zhou, Y.: Quantification of microstructural features in titanium alloys based on stereology. Rare Met. Mater. Eng. 38, 398 (2009).Google Scholar
Kelly, S.M.: Thermal and microstructure modeling of metal deposition processes with application to Ti-6Al-4V. Ph.D. Dissertation, Virginia Polytechnic Institute and State University, Blacksburg, VA, 2004.Google Scholar
Wu, X., Liang, J., Mei, J., Mitchell, C., Goodwin, P.S., and Voice, W.: Microstructures of laser-deposited Ti-6Al-4V. Mater. Des. 25, 137 (2004).Google Scholar
Ahmed, T. and Rack, H.J.: Phase transformations during cooling in α + β titanium alloys. Mater. Sci. Eng., A 243, 206 (1998).CrossRefGoogle Scholar
Elmer, J.W., Palmer, T.A., Babu, S.S., Zhang, W., and Debroy, T.: Phase transformation dynamics during welding of Ti-6Al-4V. J. Appl. Phys. 95, 8327 (2004).CrossRefGoogle Scholar
Baufeld, B., Brandl, E., and van der Biest, O.: Wire based additive layer manufacturing: Comparison of microstructure and mechanical properties of Ti-6Al-4V components fabricated by laser-beam deposition and shaped metal deposition. J. Mater. Process. Technol. 211, 1146 (2011).CrossRefGoogle Scholar
Lu, W., Shi, Y., Lei, Y., and Li, X.: Effect of electron beam welding on the microstructures and mechanical properties of thick TC4-DT alloy. Mater. Des. 34, 509–515 (2012).CrossRefGoogle Scholar
Amato, K., Hernandez, J., Murr, L.E., Martinez, E., Gaytan, S.M., Shindo, P.W., and Collins, S.: Comparison of microstructures and properties for a Ni-base superalloy (alloy 625) fabricated by electron beam melting. J. Mater. Sci. Res. 1, 3 (2012).Google Scholar
Murr, L.E., Gaytan, S.M., Ceylan, A., Martinez, E., Martinez, J.L., Hernandez, D.H., Machado, B.I., Ramirez, D.A., Medin, F., Collins, S., and Wicker, R.B.: Characterization of titanium aluminide alloy components fabricated by additive manufacturing using electron beam melting. Acta Mater. 58, 1887 (2010).Google Scholar
Gockel, J. and Beuth, J.: Understanding Ti-6Al-4V microstructure control in additive manufacturing via process maps. Proceedings of the Solid Freeform Fabrication Symposium, Bourell, D. ed.; University of Texas, Austin, TX, 2013; p. 666.Google Scholar
Gil, F.J., Ginebra, M.P., Manero, J.M., and Planell, J.A.: Formation of α-Widmanstätten structure: Effects of grain size and cooling rate on the Widmanstätten morphologies and on the mechanical properties in Ti6Al4V alloy. J. Alloys Compd. 329, 142 (2001).CrossRefGoogle Scholar
Xi, Y., Bermingham, M., Wang, G., and Dargusch, M.: Finite element modeling of cutting force and chip formation during thermally assisted machining of Ti6Al4V alloy. J. Manuf. Sci. Eng. 135, 061014 (2013).Google Scholar
Safdar, A.: A study on electron beam melted Ti-6Al-4V. M.S. Thesis, Lund University, Lund, Sweden, 2012.Google Scholar