Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-26T17:51:45.875Z Has data issue: false hasContentIssue false
  • English
  • Français

Atomic force microscopy, lateral force microscopy, and transmission electron microscopy investigations and adhesion force measurements for elucidation of tungsten removal mechanisms

Published online by Cambridge University Press:  31 January 2011

David J. Stein ,
Joseph L. Cecchi  and
Dale L. Hetherington
David J. Stein
Affiliation:
Department of Chemical and Nuclear Engineering, University of New Mexico, 209 Farris Engineering Center, Albuquerque, New Mexico 87131
Joseph L. Cecchi
Affiliation:
Department of Chemical and Nuclear Engineering, University of New Mexico, 209 Farris Engineering Center, Albuquerque, New Mexico 87131
Dale L. Hetherington
Affiliation:
Microelectronics Development Laboratory, Sandia National Laboratories, MS 1084, P.O. Box 5800, Albuquerque, New Mexico 87185–5800
Get access

Abstract

We investigated various interactions between alumina and tungsten films that occur during chemical mechanical polishing (CMP). Atomic force microscopy surface topography measurements of post-CMP tungsten indicate that the roughness of the tungsten is independent of polish pressure and rotation rate. Pure mechanical abrasion is therefore an unlikely mechanism of material removal during CMP. Transmission electron microscopy images corroborate these results. The adhesion force between alumina and tungsten was measured in solution. The adhesive force increased with KIO3 concentration. Friction forces were measured in solution using lateral force microscopy. The friction force in buffered solutions was independent of KIO3 concentration. These results indicate that interactions other than purely mechanical interactions exist during CMP.

Type
Articles
Information
Journal of Materials Research , Volume 14 , Issue 9 , September 1999 , pp. 3695 - 3706
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Li, S.H., Banvillet, H., Augagneur, C., Miller, B., Nabot-Henaff, M-P., and Wooldridge, K., Proc. of the 1998 CMP-MIC Conf., 165 (IMIC, Tampa, FL, 1998).Google Scholar
2.Kaufman, F.B., Thompson, D.B., Broadie, R.E., Jaso, M.A., Guthrie, W.L., Pearson, D.J., and Small, M.B., J. Electrochem. Soc. 138, 3460 (1991).CrossRefGoogle Scholar
3.Stein, D.J., Hetherington, D., Guilinger, T., Cecchi, J.L., J. Electrochem. Soc. 145, 3190 (1998).CrossRefGoogle Scholar
4.Kneer, E.A., Raghunath, C., Raghavan, S., and Jeon, J.S., J. Electrochem. Soc. 144, 3041 (1997).CrossRefGoogle Scholar
5.Elbel, N., Neureither, B., Müller, J., Ebersberger, B., Proc. of the 1997 CMP-MIC Conf., 75 (IMIC, Tampa, FL, 1997).Google Scholar
6.Singer, P., Semicond. Int. 48, Feb (1994)Google Scholar
7.Cook, L.M., J. Non-Cryst. Solids 120, 152 (1990).CrossRefGoogle Scholar
8.Brown, N.J., Baker, P.C., and Maney, R.T., Contemporary Methods of Optical Fabrication (SPIE, Bellingham, WA, 1981), Vol. 306.Google Scholar
9.Stein, D.J., Hetherington, D.L., and Cecchi, J.L., J. Electrochem. Soc. 146, 376 (1999).CrossRefGoogle Scholar
10.Rabinowicz, E., Friction and Wear of Materials, 2nd ed. (John Wiley and Sons, New York, 1995).Google Scholar
11.Singer, I.L., J. Vac. Sci. Technol. A 12(5), 2605 (1994).CrossRefGoogle Scholar
12.Krim, J., Langmuir 12(19), 4564 (1996).CrossRefGoogle Scholar
13.Israelachvili, J.N., Chen, Y-L., and Yoshizawa, H., J. Adhes. Sci. Technol. 8(11), 1231 (1994).CrossRefGoogle Scholar
14.Stein, D., Hetherington, D., Dugger, M., and Stout, T., J. Electron. Mater. 25, 1623 (1996).CrossRefGoogle Scholar
15.Stein, D.J., Hetherington, D.L., and Cecchi, J.L., J. Electrochem. Soc. 146, 1934 (1999).CrossRefGoogle Scholar
16.Hutchings, I.M., Tribology: Friction and Wear of Engineering Materials (CRC Press, Boca Raton, FL, 1992).Google Scholar
17. First solved by: Hertz, H., J. Math. 92 (1881). This treatment follows:Google Scholar
Timonshenko, S.P. and Goodier, J.N., Theory of Elasticity, 3rd ed. (McGraw-Hill, New York, 1969).Google Scholar
18.Montgomery, D.C., Design and Analysis of Experiments, 4th ed. (John Wiley and Sons, New York, 1997).Google Scholar
19.Stein, D. (unpublished).Google Scholar
20.Gitzen, W.H., Alumina as a Ceramic Material (American Ceramic Society, Columbus, OH, 1970).Google Scholar
21.Yih, S.W.H and Wang, C.T., Tungsten: Sources, Metallurgy, Properties, and Applications (Plenum Press, New York, 1979).CrossRefGoogle Scholar