Hostname: page-component-cd9895bd7-dk4vv Total loading time: 0 Render date: 2024-12-28T22:50:45.075Z Has data issue: false hasContentIssue false
  • English
  • Français

Oscillatory flow in curved pipes. Part 1. The developing-flow case

Published online by Cambridge University Press:  19 April 2006

T. Mullin  and
C. A. Greated
T. Mullin
Affiliation:
Department of Physics, University of Edinburgh Present address: Mathematical Institute, University of Oxford.
C. A. Greated
Affiliation:
Department of Physics, University of Edinburgh
Get access Rights & Permissions [Opens in a new window]

Abstract

The results of an experimental investigation of the entry, into a curved pipe, of the fully developed oscillatory laminar flow in a straight section are presented. Laser anemometry has been used to measure velocity profiles in the plane of the bend at various stations around a 180°-curved section. The flow development is found to depend upon both the frequency parameter of the flow and the amplitude of oscillation.

Results are presented for two values of the frequency parameter α. The first is for small α where the flow can be considered quasi-steady and the flow development is found to proceed as in previous steady-flow studies. The other case, more extensively studied, is where α has a value such that both viscous and inertial effects play important roles in establishing the basic flow at different parts of the pressure cycle. The flow development process around the curve is found to be complicated, but a general trend is found and the results are explained in terms of those already established for steady-flow development in a curved pipe.

Type
Research Article
Information
Journal of Fluid Mechanics , Volume 98 , Issue 2 , 29 May 1980 , pp. 383 - 395
Copyright
© 1980 Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Agrawal, Y., Talbot, L. & Gong, K. 1978 Laser anemometer study of flow development in curved circular pipes. J. Fluid Mech. 85, 497–518.Google Scholar
Gerrard, J. H. & Hughes, M. D. 1971 The flow due to an oscillating piston in a cylindrical tube: a comparison between experiment and simple entrance flow theory. J. Fluid Mech. 50, 97–106.CrossRefGoogle Scholar
Humphrey, J. A. C. 1977 Flow in ducts with curvature and roughness. Ph.D. thesis, University of London.
Humphrey, J. A. C. & Whitelaw, J. H. 1976 Measurements in curved flows. Proc. Squid Conf., Internal Flows, Airlie House.Google Scholar
Humphrey, J. A. C., Taylor, A. M. K. & Whitelaw, J. H. 1977 Laminar flow in a square duct of strong curvature. J. Fluid Mech. 83, 509–527.Google Scholar
Ito, H. 1961 Pressure losses in smooth pipe bends. Rep. Inst. High Speed Mech., Japan 12 (112), 41–62.Google Scholar
Mullin, T. 1978 Oscillatory flow in curved tubes. Ph.D. thesis, University of Edinburgh.
Mullin, T. & Greated, C. A. 1978 Measurement of pulsating flows by photon-correlation. J. Phys. E, Sci. Instrum. 11, 643–646.Google Scholar
Mullin, T. & Greated, C. A. 1980 Oscillatory flow in curved pipes. Part 2. The fully developed case. J. Fluid Mech. 98, 397–416.Google Scholar
Olson, D. E. 1971 Fluid mechanics relevant to respiration-flow within curved or elliptical tubes and bifurcating systems. Ph.D. thesis, University of London.
Peatap, V. S. & Spalding, D. B. 1975 Numerical computation of the flow in curved ducts. Aero. Quart. 26, 219–228.Google Scholar
Singh, M. P., Sinha, P. C. & Aggarwal, M. 1978 Flow in the entrance of the aorta. J. Fluid Mech. 87, 97–120.Google Scholar
Smith, F. T. 1976 Fluid flow into a curved pipe. Proc. Roy. Soc. A 351, 71–87.Google Scholar
Uchida, S. 1956 The pulsating viscous flow superposed on the steady motion of incompressible fluid in a circular pipe. Z. angew. Math. Phys. 7, 403–421.Google Scholar
Yao, L. S. 1978 Entry flow in a heated straight pipe. J. Fluid Mech. 88, 465–483.Google Scholar
Yao, L. S. & Berger, S. A. 1975 Entry flow in a curved pipe. J. Fluid Mech. 67, 177–196.Google Scholar