Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-26T16:34:27.605Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of speed and duration of cutting in mechanized Cheddar cheesemaking on curd particle size and yield

Published online by Cambridge University Press:  01 June 2009

Keith A. Johnston ,
Frank P. Dunlop  and
Michael F. Lawson
Keith A. Johnston
Affiliation:
New Zealand Dairy Research Institute, Private Bag, Palmerston North, New Zealand
Frank P. Dunlop
Affiliation:
New Zealand Dairy Research Institute, Private Bag, Palmerston North, New Zealand
Michael F. Lawson
Affiliation:
New Zealand Dairy Research Institute, Private Bag, Palmerston North, New Zealand
Get access Rights & Permissions [Opens in a new window]

Summary

The speed and duration of cutting the coagulum were varied during the commercial manufacture of Cheddar cheese in nine Damrow cheese vats on each of 3 consecutive days. The effects of the variations were assessed by determining the curd particle size distribution and fat and fines losses into the whey at draining. Short durations of cutting at slow speeds produced small curd particles and high fat losses into the whey. As the duration and/or speed of cutting was increased, average curd particle size increased while fat losses into the whey decreased. A maximum particle size and minimum fat level were reached after the Damrow's knife panels had completed approximately 37 revolutions. Further increases in speed and/or duration of cutting decreased curd particle size. Fat losses did not increase significantly. The hypothesis suggested to explain the results of these trials is that curd particle size is determined not by the cutting programme alone, but by a combination of the speed and duration of cutting and the subsequent speed of stirring prior to cooking. Fat losses in the whey are also influenced by this combination. Based on this hypothesis, a model is proposed which explains how variation in cutting speed and duration, followed by a constant stirring speed, determines curd particle size distribution in a Damrow cheese vat. Implications of the present findings in relation to cheese yield (losses of fat and fines into the whey) are discussed.

Type
Original Articles
Information
Journal of Dairy Research , Volume 58 , Issue 3 , August 1991 , pp. 345 - 354
Copyright
Copyright © Proprietors of Journal of Dairy Research 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Banks, J. M., Muir, D. D. & Tamime, A. Y. 1984 A comparison of cheese yield and cheesemaking efficiency using seasonal and standardized milk. Journal of the Society of Dairy Technology 37 83–88Google Scholar
Banks, J. M. & Tamime, A. Y. 1987 Seasonal trends in the efficiency of recovery of milk fat and casein in cheese manufacture. Journal of the Society of Dairy Technology 40 64–66CrossRefGoogle Scholar
Barbano, D. M. & Sherbon, J. W. 1984 Cheddar cheese yields in New York. Journal of Dairy Science 67 1873–1883CrossRefGoogle Scholar
Bynum, D. G. & Olson, N. F. 1982 Influence of curd firmness at cutting on Cheddar cheese yield and recovery of milk constituents. Journal of Dairy Science 65 2281–2290Google Scholar
Chapman, H. R. 1981 Standardisation of milk for cheesemaking at research level. Journal of the Society of Dairy Technology 34 147–152Google Scholar
De Vries, E. 1979 Test for curd-making tank, Type OST 111, with a capacity of 10,000 litres, manufactured By α-Tebel. Nederlands Instituut voor Zuivelonderzoek Rapport R110Google Scholar
De Vries, E. & Van Ginkel, W. 1980 Test of a curd-making tank, type “Damrow Double O”, with a capacity of 16,000 litres, manufactured by DEC International. Nederlands Instituut voor Zuivelonderzoek Rapport R113Google Scholar
Gilles, J. 1976 Moisture control in Cheddar cheese. New Zealand Journal of Dairy Science and Technology 11 71–72Google Scholar
Lawrence, R. C. 1991 International Dairy Federation Bulletin, in pressGoogle Scholar
Mayes, J. J. & Sutherland, B. J. 1984 Coagulum firmness and yield in Cheddar cheese manufacture the role of the curd firmness instrument in determining cutting time. Australian Journal of Dairy Technology 39 69–73Google Scholar
Mayes, J. J. & Sutherland, B. J. 1989 More notes on coagulum firmness and yield in Cheddar cheese manufacture. Australian Journal of Dairy Technology 44 47–48Google Scholar
Olson, N. F. 1977 Factors affecting cheese yields. Dairy industries International 42(4) 14–15, 19Google Scholar
Phelan, J. A. 1981 Standardisation of milk for cheesemaking at factory level. Journal of the Society of Dairy Technology 34 152–156Google Scholar
Van Ginkel, W. A., De Vries, E. & Daamen, C. B. G. 1987 Test of a curd-making tank, Type 3113–15000 Code No. 3113–1049, with a capacity of 15,000 litres, manufactured by Pasilac Silkeborg. Nederlands Instituut voor Zuivelonderzoek Rapport R125Google Scholar
Whitehead, H. R. & Harkness, W. L. 1954 The influence of variations in cheesemaking procedure on the expulsion of moisture from Cheddar cheese curd. Australian Journal of Dairy Technology 9 103–107Google Scholar