Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-26T04:56:32.891Z Has data issue: false hasContentIssue false

The effect of high-temperature heat treatment and homogenization on the microstructure of set yogurt curd networks

Published online by Cambridge University Press:  31 August 2023

Takefumi Ichimura*
Affiliation:
Food Science & Technology Research Laboratories R&D Division, Meiji Co., Ltd., 1-29-1 Nanakuni, Hachiouji, Tokyo 192-0919, Japan
Mai Kusaka
Affiliation:
Department of Life Science, Meiji University, Tama-ku, Kawasaki 214-8571, Japan
Taku Nakamura
Affiliation:
Department of Life Science, Meiji University, Tama-ku, Kawasaki 214-8571, Japan
*
Corresponding author: Takefumi Ichimura; Email: [email protected]
Rights & Permissions [Opens in a new window]

Abstract

Set yogurt's physical characteristics are greatly affected by the homogenization and heat treatment processes. In our previous study, set yogurt treated at 130°C and with the fat particle size reduced to ≤0.6 μm had equivalent curd strength, less syneresis and smoother texture than yogurt treated at 95°C. When investigating the mechanisms underlying yogurt's physical properties, it is important to evaluate the yogurt's microstructure. We conducted electron microscopy evaluations to investigate the mechanisms of changes in yogurt's physical properties caused by 130°C heat treatment and by a reduction in the fat globule size. We prepared yogurt mixtures by combining heat treatment at 95 and 130°C and homogenization pressure at 10 + 5 and 35 + 5 MPa and then fermented the mixtures in a common yogurt starter. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used for the structural observations. Fine particles were observed on the surface of the casein micelles of the yogurt treated at 95°C, and the coalescence density between micelles was high. The surface of the yogurt treated at 130°C had few fine particles, and the coalescence density between micelles was low. The yogurt treated at 130°C with 35 + 5 MPa homogenization had low coalescence density between casein micelles, but smaller-particle-size fat globules increased the network density. Approximately 30% of the fat globules were estimated to be incorporated into the yogurt networks compared to the volume of casein micelles. We speculate that 130°C heat treatment alters the structure of whey protein on the surface of casein micelles and interferes with network formation, but reducing the size of fat globules reinforces the network as a pseudoprotein.

Type
Research Article
Creative Commons
Creative Common License - CCCreative Common License - BY
This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted re-use, distribution and reproduction, provided the original article is properly cited.
Copyright
Copyright © The Author(s), 2023. Published by Cambridge University Press on behalf of Hannah Dairy Research Foundation

The curd strength of set yogurt and customer satisfaction with set yogurt are greatly affected by the yogurt's physical characteristics and texture (Aryana and Olson, Reference Aryana and Olson2017). The microstructure of foods generally has an important influence on the foods' physical properties, and many studies linking physical property evaluations and structural observations of foods have been reported (Pascua et al., Reference Pascua, Koç and Foegeding2013; Saldana et al., Reference Saldaña, Behrens, Serrano, Ribeiro, de Almeida and Contreras-Castilloa2015; Joardder et al., Reference Joardder, Kumar and Karim2017). When modifications of physical properties are sought, microstructural analyses can provide useful information (Aguilera, Reference Aguilera2005), and a microstructural evaluation can support an evaluation of physical properties. Evaluations of the microstructure of yogurt have been performed mainly with confocal laser scanning microscopy (CLSM: Bai et al., Reference Bai, Huang, Guo, Wang, Wang, Kwok, Dan, Zhang and Bilige2020; Wang et al., Reference Wang, Kristo and LaPointe2020; Jia et al., Reference Jia, Zhao, Tao, Yu, Liu and Cui2022), scanning electron microscopy (SEM: Zhang et al., Reference Zhang, McCarthy, Wang, Liu and Guo2015; Jia et al., Reference Jia, Zhao, Tao, Yu, Liu and Cui2022), and transmission electron microscopy (TEM: Harte et al., Reference Harte, Amonte, Luedecke, Swanson and Barbosa-Cánovas2002).

Yogurt's physical characteristics are greatly affected by heat treatment processes (Xu et al., Reference Xu, Emmanouelidou, Raphaelides and Antoniou2008), and yogurt is usually pasteurized at 90°–95°C for 5–10 min (Sodini et al., Reference Sodini, Remeuf, Haddad and Corrieu2014). A low denaturation rate of whey due to low pasteurization temperatures results in a significant decrease in the viscosity and firmness of yogurt (Dannenberg and Kessler, Reference Dannenberg and Kessler1988). However, the viscosity and firmness of the yogurt will also decrease significantly if the pasteurization is performed at ≥120°C (Krasaekoopt et al., Reference Krasaekoopt, Bhandari and Deeth2003). Milk for human consumption (i.e., drinking milk) is generally pasteurized by a high-temperature short-time or ultra-high temperature (UHT) method (Lorenzen et al., Reference Lorenzen, Clawin-Radecker, Einhoff, Hammer, Hartmann, Hoffmann, Martin, Molkentin, Walte and Deverse2011) and it is, therefore, usually not possible to use the same pasteurizer for drinking milk and yogurt.

The pasteurization conditions for drinking milk differ slightly from country to country, and in Japan drinking milk is pasteurized at 125°–135°C for 2–5 s (Ohkubo et al., Reference Ohkubo, Uchida, Motoshima and Katano2019). We recently developed a method of producing set yogurt by pasteurization at 125°–135°C for 2–5 s and homogenization at 30–40 + 5 MPa giving a reduction of fat globule size to ≤0.6 μm (Ichimura et al., Reference Ichimura, Osada, Yonekura and Horiuchi2022). The set yogurt obtained by this method has the same firmness, less syneresis and better smoothness than yogurt prepared by general manufacturing conditions (90°–95°C, 10–20 + 5 MPa), and it was significantly preferred in a sensory evaluation.

The effects of heat treatment and homogenization conditions on the physical characteristics of yogurt have been examined by several research groups. When the milk used for yogurt is heated, the heat-denatured beta-lactoglobulin (β-Lg) and alpha-lactalbumin (α-La) bind to the κ-casein of casein micelles (Elfagm and Wheelock, Reference Elfagm and Wheelock1978). The binding of casein micelles and whey by heat treatment increases the firmness of the yogurt and changes the isoelectric point to the high pH side (Donato et al., Reference Donato, Alexander and Dalgleish2007). The denaturation rate of whey by heat treatment has an important effect on the firmness of yogurt (Dannenberg and Kessler, Reference Dannenberg and Kessler1988), but heat treatment at temperatures >120°C reduces the firmness of yogurt regardless of the whey denaturation rate (Savello and Dargan, Reference Savello and Dargan1995). In addition, the mechanisms involved in the reduction of yogurt firmness have not been known.

After homogenization, casein micelles, β-Lg, and α-La locate to the surface of the yogurt's fat globules (Hayes et al., Reference Hayes, Fox and Kelly2005). The amount of casein micelles present on the fat globule surface increases as the homogenization temperature and pressure increase (Cano-Ruiz and Richter, Reference Cano-Ruiz and Richter1997). Homogenization using ultra-high pressure (>100 MPa) improves the syneresis and physical properties of yogurt (Serra et al., Reference Serra, Trujillo, Jaramillo, Guamis and Ferragut2008), but there are few data regarding the effects of 30- to 90-MPa homogenization.

The mechanisms underlying changes that occur in the curd structure when 130°C heat treatment and homogenization pressure that is higher than conventional conditions (such as 35 + 5 MPa) are used are not yet known. Our CLSM observations confirmed that the structure of the yogurt changed (Ichimura et al., Reference Ichimura, Osada, Yonekura and Horiuchi2022). Regarding the effect that fat globules have of reinforcing the curd network, we speculated that it is possible that the fat globules may adhere to or otherwise be included in the network. If the mechanisms that underlie the changes in physical properties that occur with an increase of the heat treatment temperature from 95  to 130°C and a reduction of the fat globule size can be clarified, useful knowledge for producing set yogurt with a good texture will be obtained. We thus conducted the present study to investigate the mechanisms of changes in the physical properties of set yogurt by identifying the precise structural changes that are the results of several heat treatment and homogenization conditions. We used SEM and TEM to observe the microstructure of the yogurt samples and to identify the details of the network structure.

Materials and methods

Set yogurt preparation

Culture LB81, which contains Lactobacillus delbrueckii subsp bulgaricus 2038 and Streptococcus thermophiles 1131, was used in this study. The preparation of the yogurt starter was as described by Ichimura et al. (Reference Ichimura, Osada, Yonekura and Horiuchi2022). The yogurt mixture was obtained by mixing raw milk, skim milk powder and water; it contained 3.0% (wt/wt) fat, 9.5% (wt/wt) SNF (solids-not-fat) and 3.6% (w/w) protein. The raw milk and skim milk powder were supplied by Meiji Co. (Tokyo) facilities. The yogurt mixture was pre-warmed at 75°C. Prior to the heat treatment described below, each mixture was homogenized (model H20, Sanwa Engineering, Hyogo, Japan) at 10 (first stage) + 5 MPa (second stage) or 35 + 5 MPa. The yogurt mixtures were then pasteurized at 95°C for 5 min or at 130°C for 2 s. Heat treatment at 95°C for 5 min was conducted as vat heat treatment. The heat treatment at 130°C for 2 s (experimental preparation conditions) was conducted with an indirect plate exchange system (Powerpoint International, Saitama, Japan). In this study, we defined the control preparation conditions as heat treatment at 95°C for 5 min and homogenization at 10 and 5 MPa. The yogurt mixtures' inoculation, fermentation, and sample cooling were carried out as described by Ichimura et al. (Reference Ichimura, Osada, Yonekura and Horiuchi2022). Detailed methodologies are given in the online Supplementary File, including a process flow chart at Supplementary Fig. S1.

Particle-size distribution

We determined the distribution of the sizes of the fat particles of the yogurt mixture by a laser diffraction scattering method with a laser diffraction particle size analyzer (SALD2200, Shimadzu, Kyoto, Japan) as follows. The yogurt mixture was added into the circulating cell of the apparatus containing deionized water. Triplicate measurements were taken at 25°C, and the volume-weighted mean diameters (d4,3) were recorded. Assuming that the distribution of fat globules follows a normal distribution, we calculated the volume of fat globules smaller than ‘x’ μm (F x) contained in 100 g of yogurt mixture by using the mean value and standard deviation of the fat globules. The lower cumulative distribution of the fat globules of ‘x’ μm (Fx) was estimated with the use of the standard normal distribution table. (Fx) was approximated with the following equation:

$$( {F_x} ) = [ {{\rm fat}\,( \% ) \,/\,{\rm s}{\rm .g} ._{{\rm fat}}} ] \,\times \,P( {\rm x}, \;{\rm \mu }, \;{\rm \sigma }) $$

where (Fx) is the volume of the fat globules smaller than x μm contained in 100 g of yogurt mixture, s.g.fat is the specific gravity of the milk fat, and P(x, μ, σ) is the lower cumulative distribution. For further detail see online Supplementary Fig. S2.

Physical characterization of the yogurt

The physical characteristics of the yogurt were the curd hardness, curd firmness, penetration angle and the degree of syneresis. The curd hardness and curd firmness of yogurt represent the yogurt's tolerance to vibration during transport. The penetration angle represents the smoothness of the yogurt. The degree of syneresis is an index of syneresis to the surface. The measurements of the curd hardness, curd firmness, penetration angle, and the degree of syneresis of the yogurt samples were carried out as described by Ichimura et al. (Reference Ichimura, Osada, Yonekura and Horiuchi2022).

Scanning electron microscopy

SEM observations were performed to evaluate the set yogurt's microscopic networks. Yogurt samples were cut to 3 mm × 3 mm × 5 mm cubes and then soaked in a glutaraldehyde solution (2% final concentration) for 1 h. The cubes were washed twice with deionized water and soaked in osmium tetroxide solution (1% final concentration) for 90 min. The cubes were then washed twice with deionized water and dehydrated by soaking in 30, 50, 60, 70, 80, 90, and 99% ethanol (vol/vol) for 10, 10, 10, 10, 15, 15, and 15 min, respectively. The cubes were then soaked in 100% ethanol for 15 min, two times. The cubes were then soaked in isoamyl acetate for 20 min, two times, and then critical-point dried with the use of liquefied carbon dioxide (JCPD-5; JEOL, Tokyo) and coated with a layer of sublimated osmium plasma coater (NL-OPC80N; JEOL). The osmium-coated cubes were then viewed by SEM (JSM-6700F; JEOL).

Transmission electron microscopy

TEM observations were performed to evaluate the sizes of the fat globules in the networks of the set yogurt made by 130°C heat treatment mix. The yogurt samples for the TEM examination were treated in the same way as the samples for SEM up to the point of being soaked in osmium tetroxide solution. After the samples were soaked in that solution, they were dyed in an EM Stainer (Nissin EM Co., Tokyo) for 15 min. The samples were then dehydrated by soaking in 30, 50, 60, 70, 80, 90, and 99% ethanol (vol/vol) for 10, 10, 10, 10, 15, 15, and 15 min, respectively. The cubes were soaked in 100% ethanol for 15 min, two times. Next, 43.4 g of Quetol 651, 20.3 g of NSA, 48.5 g MNA, and 1.5 ml of DMP-30 (all from Nissin EM Co.) were mixed to create an epoxy resin solution for embedding. The dehydrated samples were soaked in propylene oxide solution, then a propylene oxide solution:epoxy resin solution = 1:1 mixture, a propylene oxide solution:epoxy resin solution = 1:3 mixture, and the epoxy resin solution for 60 min, respectively. The samples were then soaked in epoxy resin solution overnight with shaking. Afterward, the samples were poured into gelatin capsules with the resin solution. The resin solution with the samples was heated at 60°C for two nights, with the use of a thermostat. After the resin was cured, the samples were sectioned at 100-nm-thick with an ultramicrotome (Ultracut UCT; Leica Biosystems, Buffalo Grove, IL) and a diamond knife (DiATOME Ultra 45; EMJapan Co., Tokyo) and mounted on copper grids. Thin sections were dyed in the EM Stainer for 15 min and then dyed with acetate uranium (1% final concentration) to enable observation. The examination was performed with a transmission electron microscope (JEM-2010; JEOL) at an acceleration voltage of 140 kV. We defined the white circle observed in the image as the fat globule and measured its diameter at three locations; the average value was calculated.

Statistical analysis

A one-way repeated measures analysis of variance (ANOVA) and Tukey-Kramer adjustment were used to investigate the effects of differences in test conditions on the yogurts' physical properties and the sensory evaluation. The data were analyzed using Bellcurve for Excel (ver. 3.10, Social Survey Research Information, Tokyo) to find significant differences among the samples. Differences were considered significant when P < 0.05.

Results

Physical characterization of the yogurt

The particle sizes of the fat globules depended on the homogenization pressure (Table 1). Homogenization at 10 + 5 MPa reduced the fat globule size to 1.0 μm, and homogenization at 35 + 5 MPa reduced the fat globule size to 0.5 μm. Table 1 lists the physical characteristics of the yogurt. The curd firmness was highest in the experimental yogurts processed at 95°C-35 + 5 MPa and lowest in the experimental yogurts processed at 130°C-10 + 5 MPa. Regarding the penetration angle, the yogurt processed at 95°C 35 + 5 MPa had the highest penetration angle of the two. The control yogurt made with the 95°C-10 + 5 MPa processing conditions showed the greatest syneresis, and the 130°C-35 + 5 MPa condition produced the lowest syneresis. These results were consistent with those obtained in our earlier study (Ichimura et al., Reference Ichimura, Osada, Yonekura and Horiuchi2022).

Table 1. The conditions used to make the yogurt mixes and the resulting particle-size distributions

1Two-stage homogenization (first stage and second stage) at 75°C.

2Values with different letters in the same column are significantly different (P < 0.05).

3Vat heat treatment.

4Indirect plate exchange system (Powerpoint International, Tokyo).

The microstructure of the yogurt

Figures 1 and 2 are SEM images of the network structure of yogurt. A lower magnification image is provided at online Supplementary Fig. S3. Figure 1 shows a detailed yogurt network structure. The network structure obtained with the 130°C-10 + 5 MPa condition tended to be thin, and the network from the 95°C-35 + 5 MPa condition tended to be thick. Figure 2 depicts the appearance of casein micelles in the yogurt network. The casein micelles in the yogurt network made at 130°C had a pleated surface and many gaps inside the casein micelle had aggregate. In contrast, the yogurt made with the 95°C treatment had fine ~10-nm particles bonded to the surface of casein micelles instead of a pleated structure. In addition, there were few gaps in the casein micelle assembly, and the structure was dense.

Figure 1. Scanning electron micrographs of yogurts with different conditions of homogenization and heat-treatment temperature. A: Heat treatment at 95°C for 5 min and homogenization at 10 + 5 MPa. B: Heat treatment at 130°C for 2 s and homogenization at 10 + 5 MPa. C: Heat treatment at 95°C for 5 min and homogenization at 35 + 5 MPa. D: Heat treatment at 130°C for 2 s and homogenization at 35 + 5 MPa.

Figure 2. Scanning electron micrographs of yogurts with different conditions of homogenization and heat-treatment temperature. A: Heat treatment at 95°C for 5 min and homogenization at 10 + 5 MPa. B: Heat treatment at 130°C for 2 s and homogenization at 10 + 5 MPa. C: Heat treatment at 95°C for 5 min and homogenization at 35 + 5 MPa. D: Heat treatment at 130°C for 2 s and homogenization at 35 + 5 MPa. White arrows: fine particles on the surface of the casein micelles.

Regarding the size of casein micelles in the yogurt network, there was no significant difference between the 95  and 130°C heat treatments, as the size of the micelles for both heat treatment values were approx. 100–200 nm. Figure 3 is TEM images of the internal structure of the network of yogurt made by 130°C heat treatment; small fat globules ≤0.4 mm tended to be included in the yogurt network. The yogurt made by homogenization at 10 + 5 MPa tended to have fat globules outside the network, whereas in the yogurt made by homogenization at 35 + 5 MPa, fat globules tended to exist inside the network.

Figure 3. Transmission electron micrographs of yogurts made by heat treatment at 130°C with different conditions of homogenization pressure. A: Heat treatment at 130°C for 2 s and homogenization at 10 + 5 MPa. B: Heat treatment at 130°C for 2 s and homogenization at 35 + 5 MPa. Casein micelles are black and fat globules are white. White arrows: fat globules. Numbers: The sizes of fat the globules (μm).

Discussion

To the best of our knowledge, this study is the first to examine in detail the microstructure of set yogurt made by 130°C heat treatment. There is a report by Savello and Dargan (Reference Savello and Dargan1995) regarding the physical properties of set yogurt made by heating at 130°C, but it does not mention the microstructure. The effects of the 130°C heat treatment and homogenization pressure on the microstructure of yogurt were clarified by our present findings. The highest curd firmness (obtained in yogurt produced at 95°C-35 + 5 MPa) tended to have a thick network, and the lowest curd firmness (the yogurt produced at 130°C-10 + 5 MPa) tended to have a thin network (Fig. 1). That is, the network thickness affected the curd firmness of the yogurt. A thin and dense structure is less likely to produce agglomerates when the network collapses, and we therefore speculated that this is why the penetration angle, which indicates the roughness of the texture, became low in both yogurt types (Table 1).

In addition, the 130°C heat treatment tended to reduce the aggregation of casein micelles and increase the surface exposed to voids in the binding of casein particles, which resulted in small gaps in the network and high density (Fig. 1) as well as least syneresis (Table 1). We thus inferred that the mechanism by which syneresis was reduced by 130°C heat treatment originated from an increase in the hydration area of the casein micelles. We also infer that the mechanism by which syneresis was decreased by a reduction in the fat globule size originated from an increase in the surface area of the fat globules emulsified by milk proteins, resulting in an increase in the hydration area.

In the 130°C heat treatment, unlike the 95°C heat treatment, little binding of fine particles was detected on the surface of the casein micelles (Fig. 2). We also observed that the yogurt made with 130°C heat treatment had many gaps in the structure of networks and that there were a few aggregates due to the coalescence of the casein micelles (Fig. 1). With heat treatment, β-Lg binds to κ-casein via disulfide bonds (Edwin et al., Reference Edwin, Anema, Bienvenue, Boland, Creamer and Jimenez-Flores2004), which increases the hydrophobicity of the casein micelles and enhances the curd strength of yogurt (Mottar et al., Reference Mottar, Bassier, Joniau and Baert1989). On the other hand, heat treatment above 120°C reduces the curd strength of yogurt regardless of the whey denaturation rate (Krasaekoopt et al., Reference Krasaekoopt, Bhandari and Deeth2003). Phoebe et al. (Reference Phoebe, Ren, Xiao and Tomasula2015) confirmed that UHT sterilization (135°C for 2 s) partially disrupts the secondary and tertiary structures of whey protein (β-Lg and α-La) which results in the formation of an amorphous string-like structure around the casein micelles (Li et al., Reference Li, Ye and Singh2021) We speculated that these changes inhibited the interaction between casein micelles after heat treatment at 130°C, that is, yogurt network formation.

Figure 2 shows that the yogurt made with 130°C heat treatment had a thinner network structure, and the yogurt made with 35 + 5 MPa homogenization had a thicker network structure. Not only casein micelles but also fat globules were taken into the network, and they reinforced the structure (Fig. 3). We speculated that fat globules ≤0.4 mm in size would be taken into the yogurt networks. When we calculated the ratio of the volume of fat globules <0.4 μm (F 0.4) to the volume of casein from the specific density of casein micelles (1.333) and fat globules (0.916), the results confirmed that in the 130°C-35 + 5 MPa condition, the ratios were particularly high (Table 2). The density of fat globules was described by Cano-Ruiz and Richter (Reference Cano-Ruiz and Richter1997), and we estimated the density of the casein micelles from the report by Ono (Reference Ono2005). Our present findings thus indicate that the reason that the curd strength increases when the homogenization pressure is increased is because the fine fat globules became network constituents, like pseudo-casein micelles.

Table 2. Calculated ratio of volume of casein micelles and fat globules in the fat-containing yogurt mix

a Calculated from the particle-size distribution and the amount of fat.

b Calculated from <0.4 μm fat volume and the amount of protein.

In conclusion, we have investigated the differences in the physical properties of yogurt made with the use of different heat-treatment temperatures and homogenization conditions, focusing on the network structure. Electron microscopy revealed that fat globules smaller than 0.4 μm were present in the network, increasing the network density. Whey proteins on the surface of casein micelles were clearly visible with the 95°C heat treatment, whereas no clear structure was observed in the 130°C heat treatment. We speculate that the 130°C heat treatment changed the structure of whey proteins on the surface of casein micelles, preventing network formation, whereas smaller fat globules reinforced the network as pseudo-proteins. Our present evaluation of the network structure clarified the causes underlying the effects of the manufacturing conditions on the physical properties of yogurt.

Supplementary material

The supplementary material for this article can be found at https://doi.org/10.1017/S0022029923000523

Acknowledgements

We thank Hiroshi Horiuchi, Takashi Osada, and Megumi Takai for the many useful comments on this research. We also thank Tomoko Ichiba and Nao Takagi for their assistance with the yogurt samples' preparation and evaluation.

References

Aguilera, JM (2005) Why food microstructure? Journal of Food Engineering 67, 311.CrossRefGoogle Scholar
Aryana, KJ and Olson, DW (2017) A 100-year review: yogurt and other cultured dairy products. Journal of Dairy Science 100, 998710013.CrossRefGoogle ScholarPubMed
Bai, M, Huang, T, Guo, S, Wang, Y, Wang, J, Kwok, L-Y, Dan, T, Zhang, H and Bilige, M (2020) Probiotic Lactobacillus casei Zhang improved the properties of stirred yogurt. Food Bioscience 37, 100718.CrossRefGoogle Scholar
Cano-Ruiz, ME and Richter, RL (1997) Effect of homogenization pressure on the milk fat globule membrane proteins. Journal of Dairy Science 80, 27322739.CrossRefGoogle Scholar
Dannenberg, F and Kessler, HG (1988) Effect of denaturation of β-lactoglobulin on texture properties of set-style nonfat yoghurt. 2. Firmness and flow properties. Milchwissenschaft 43, 700704.Google Scholar
Donato, L, Alexander, M and Dalgleish, DG (2007) Acid gelation in heated and unheated milks: interactions between serum protein complexes and the surface of casein micelles. Journal of Agricultural and Food Chemistry 55, 41604168.CrossRefGoogle ScholarPubMed
Edwin, KL, Anema, SG, Bienvenue, A and Boland, MJ, Creamer, LK and Jimenez-Flores, R (2004) Heat-induced redistribution of disulfide bonds in milk proteins. 2. Disulfide bonding patterns between bovine β-lactoglobulin and κ-casein. Journal of Agricultural and Food Chemistry 52, 76697680.Google Scholar
Elfagm, AA and Wheelock, JV (1978) Interaction of bovin α-lactalbumin and β-lactoglobulin in heated milk. Journal of Dairy Science 61, 2832.CrossRefGoogle Scholar
Harte, F, Amonte, M, Luedecke, L, Swanson, BG and Barbosa-Cánovas, GV (2002) Yield stress and microstructure of set yogurt made from high hydrostatic pressure-treated full fat milk. Food Science 67, 22452250.CrossRefGoogle Scholar
Hayes, MG, Fox, PF and Kelly, AL (2005) Potential applications of high pressure homogenization in processing of liquid milk. Journal of Dairy Research 72, 2533.CrossRefGoogle ScholarPubMed
Ichimura, T, Osada, T, Yonekura, K and Horiuchi, H (2022) A new method for producing superior set yogurt, focusing on heat treatment and homogenization. IDF factsheet 001/2018–02. Heat treatment of milk – overview. Journal of Dairy Science 105, 29782987.CrossRefGoogle Scholar
Jia, S, Zhao, H, Tao, H, Yu, B, Liu, P and Cui, B (2022) Influence of corn resistant starches type III on the rheology, structure, and viable counts of set yogurt. International Journal of Biological Macromolecules 203, 1018.CrossRefGoogle ScholarPubMed
Joardder, MUH, Kumar, C and Karim, MA (2017) Food structure: its formation and relationships with other properties. Critical Reviews in Food Science and Nutrition 57, 11901205.CrossRefGoogle ScholarPubMed
Krasaekoopt, W, Bhandari, B and Deeth, H (2003) Yogurt from UHT milk: a review. Australian Journal of Dairy Technology 58, 2629.Google Scholar
Li, S, Ye, A and Singh, H (2021) Physicochemical changes and age gelation in stored UHT milk: seasonal variations. International Dairy Journal 118, 110.CrossRefGoogle Scholar
Lorenzen, PC, Clawin-Radecker, I, Einhoff, K, Hammer, P, Hartmann, R, Hoffmann, W, Martin, D, Molkentin, J, Walte, HG and Deverse, M (2011) A survey of the quality of extended shelf life (ESL) milk in relation to HTST and UHT milk. International Journal of Dairy Technology 64, 166178.CrossRefGoogle Scholar
Mottar, J, Bassier, A, Joniau, M and Baert, J (1989) Effect of heat-induced association of whey proteins and casein micelles on yogurt texture. Journal of Dairy Science 72, 22472256.CrossRefGoogle Scholar
Ohkubo, Y, Uchida, K, Motoshima, H and Katano, N (2019) Microbiological safety of UHT milk treated at 120℃ for 2s, as estimated from the distribution of high-heat-resistant Bacillus cereus in dairy environments. International Dairy Journal 91, 3640.CrossRefGoogle Scholar
Ono, T (2005) Applied aspects derived from the relationship between calcium and milk proteins. Milk Science 54, 5362.Google Scholar
Pascua, Y, Koç, H and Foegeding, EA (2013) Food structure: roles of mechanical properties and oral processing in determining sensory texture of soft materials. Current Opinion in Colloid & Interface Science 18, 324333.CrossRefGoogle Scholar
Phoebe, X, Ren, D, Xiao, Y and Tomasula, PM (2015) Effect of homogenization and pasteurization on the structure and stability of whey protein in milk. Journal of Dairy Science 98, 28842897.Google Scholar
Saldaña, E, Behrens, JH, Serrano, JS, Ribeiro, F, de Almeida, MA and Contreras-Castilloa, CJ (2015) Microstructure, texture profile and descriptive analysis of texture for traditional and light mortadella. Food Structure 6, 1320.CrossRefGoogle Scholar
Savello, PA and Dargan, RA (1995) Improved yogurt physical properties using ultrafiltration and very-high temperature heating. Milchwissenschaft 50, 8690.Google Scholar
Serra, M, Trujillo, AJ, Jaramillo, PD, Guamis, B and Ferragut, V (2008) Ultra-high puressure homogenization-induced changes in skim milk: impact on aced coagulation properties. Journal of Dairy Research 75, 6975.CrossRefGoogle Scholar
Sodini, I, Remeuf, F, Haddad, S and Corrieu, G (2014) The relative effect of milk base, starter, and process on yogurt texture: a review. Critical Reviews in Food Science and Nutrition 44, 113137.CrossRefGoogle Scholar
Wang, X, Kristo, E and LaPointe, G (2020) Adding apple pomace as a functional ingredient in stirred-type yogurt and yogurt drinks. Food Hydrocolloids 100, 105453.CrossRefGoogle Scholar
Xu, ZM, Emmanouelidou, DG, Raphaelides, SN and Antoniou, KD (2008) Effects of heating temperature and fat content on the structure development of set yogurt. Journal of Food Engineering 85, 590597.CrossRefGoogle Scholar
Zhang, T, McCarthy, J, Wang, G, Liu, Y and Guo, M (2015) Physiochemical properties, microstructure, and probiotic survivability of nonfat goats’ milk yogurt using heat-treated whey protein concentrate as fat replacer. Journal of Food Science 80, M788M794.CrossRefGoogle ScholarPubMed
Figure 0

Table 1. The conditions used to make the yogurt mixes and the resulting particle-size distributions

Figure 1

Figure 1. Scanning electron micrographs of yogurts with different conditions of homogenization and heat-treatment temperature. A: Heat treatment at 95°C for 5 min and homogenization at 10 + 5 MPa. B: Heat treatment at 130°C for 2 s and homogenization at 10 + 5 MPa. C: Heat treatment at 95°C for 5 min and homogenization at 35 + 5 MPa. D: Heat treatment at 130°C for 2 s and homogenization at 35 + 5 MPa.

Figure 2

Figure 2. Scanning electron micrographs of yogurts with different conditions of homogenization and heat-treatment temperature. A: Heat treatment at 95°C for 5 min and homogenization at 10 + 5 MPa. B: Heat treatment at 130°C for 2 s and homogenization at 10 + 5 MPa. C: Heat treatment at 95°C for 5 min and homogenization at 35 + 5 MPa. D: Heat treatment at 130°C for 2 s and homogenization at 35 + 5 MPa. White arrows: fine particles on the surface of the casein micelles.

Figure 3

Figure 3. Transmission electron micrographs of yogurts made by heat treatment at 130°C with different conditions of homogenization pressure. A: Heat treatment at 130°C for 2 s and homogenization at 10 + 5 MPa. B: Heat treatment at 130°C for 2 s and homogenization at 35 + 5 MPa. Casein micelles are black and fat globules are white. White arrows: fat globules. Numbers: The sizes of fat the globules (μm).

Figure 4

Table 2. Calculated ratio of volume of casein micelles and fat globules in the fat-containing yogurt mix

Supplementary material: PDF

Ichimura et al. supplementary material

Ichimura et al. supplementary material

Download Ichimura et al. supplementary material(PDF)
PDF 437.6 KB