Guaranteeing charge conservation of empirically extracted Gallium Nitride (GaN) High-Electron-Mobility Transistor (HEMT) models is necessary to avoid simulation issues and artifacts in the prediction. However, dispersive effects, such as thermal and charge-trapping phenomena, may compromise the model extraction flow resulting in poor model accuracy. Although GaN HEMT models should be extracted, in principle, from an isodynamic dataset, this work deals with the systematic identification of an approximate, yet most suitable, charge-conservative empirical model from standard multi-bias S-parameters, i.e., from non-isodynamic data. Results show that the obtained model maintains a reasonable accuracy in predicting both small- and large-signal behavior, while providing the benefits of charge conservation.

This paper presents a comparison of chip connections using aerosol jet (AJ) and bond technology on low-cost printed circuit board (PCB) substrates. First, the behavior of the used gap filler material and the used silver ink for AJ technology on PCBs are characterized. In addition to comparing the radio frequency (RF) performance (DC to 67 GHz) of the two technologies, the mechanical stability is also compared. While the AJ technology transitions score above all for their RF performance and the lower requirements (surface finish, pad size, and adhesion) on the PCB, the bonding technology has clear advantages, especially with a different coefficient of thermal expansion values of the substrates to be connected. Finally, the measurement results of a complete package are shown, whereby the chip connection is realized once by means of AJ and once by bonding wires.

In the area of electromagnetic metrology, binary coded excitation signals become more and more important and various binary coded sequences are available. The measurement approach is to assess the impulse response function of a device under test by correlating the response signal with the excitation signal. In order to achieve a high measurement reproducibility as well as a high dynamic range, the generated binary coded signals have to provide low-noise. In this contribution, a low-noise signal generator realized with a field programmable gate array is presented. The performance investigation of different kinds of binary coded excitation signals and different correlation concepts have been practically investigated. With a chip rate of 5 Gchip/s, the generator can be utilized for ultra-wideband applications. In order to allow for a low-noise and long-term stable signal generation, a new clock generator concept is presented and results of phase noise measurements are shown. Furthermore, an algorithm to fast and precisely shifting the time lag between two binary coded signals for correlating excitation and response signals with a hardware correlator is presented. Finally, the realized demonstrator system is tested using two commonly used types of binary coded sequences.

This paper reports on a record-low-phase noise D-band signal source with 5 dBm output power, and 1.3 GHz tuning range. The source is based on the unconventional combination of a fundamental frequency 23 GHz oscillator in 150 nm AlGaN/GaN HEMT technology followed by a 130 nm SiGe BiCMOS MMIC including a sixtupler and an amplifier. The amplifier operates in compression mode as power-limiting amplifier, to equalize the source output power so that it is nearly independent of the oscillator's gate and drain bias voltages used for tuning the frequency of the source. The choice of using a GaN HEMT oscillator is motivated by the need for a low oscillator noise floor, which recently has been demonstrated as a bottle-neck for data rates in wideband millimeter-wave communication systems. The phase noise performance of this signal source is −128 dBc/Hz at 10 MHz-offset. To the best of the authors’ knowledge, this result is the lowest reported phase noise of D-band signal source.

The design of mixed-technology quasi-reflectionless planar bandpass filters (BPFs), bandstop filters (BSFs), and multi-band filters is reported. The proposed quasi-reflectionless filter architectures comprise a main filtering section that determines the power transmission response (bandpass, bandstop, or multi-band type) of the overall circuit network and auxiliary sections that absorb the reflected radio-frequency (RF) signal energy. By loading the input and output ports of the main filtering section with auxiliary filtering sections that exhibit a complementary transfer function with regard to the main one, a symmetric quasi-reflectionless behavior can be obtained at both accesses of the overall filter. The operating principles of the proposed filter concept are shown through synthesized first-order BPF and BSF designs. Selectivity-increase techniques are also described. They are based on: (i) cascading in-series multiple first-order stages and (ii) increasing the order of the filtering sections. Moreover, the RF design of quasi-reflectionless multi-band BPFs and BSFs is discussed. A hybrid integration scheme in which microstrip-type and lumped-elements are effectively combined within the filter volume is investigated for size miniaturization purposes. For experimental validation purposes, two quasi-reflectionless BPF prototypes (one- and two-stage architectures) centered at 2 GHz and a second-order BSF prototype centered at 1 GHz were designed, manufactured, and measured.

This paper presents slow-wave transmission lines based on non-periodic reactive loading. Specifically, the loading elements are stepped impedance shunt stubs (SISS). By sacrificing periodicity using SISS tuned to different frequencies, multiple transmission zeros above the pass band arise, and the rejection level and bandwidth of the stop band is improved as compared with those of periodic structures. Through a proper design, it is possible to achieve compact lines, simultaneously providing the required electrical length and characteristic impedance at the design frequency (dictated by specifications), and efficiently filtering the response at higher frequencies. These lines are applied to the design of a compact power splitter with filtering capability in this work. The length of the splitter, based on a 35.35 Ω impedance inverter, is reduced by a factor of roughly two. Moreover, harmonic suppression better than 20 dB up to the fourth harmonic is achieved.

With the aim of performing perimeter surveillance of high-speed railway networks, this paper presents the design of a passive multistatic radar system based on the use of Long-Term Evolution (LTE) downlink signals as the illumination of opportunity. Taking into account the specifications and standard of the LTE system, the ambiguity function of measured downlink signals is analyzed in terms of range and Doppler resolution, ambiguities, and sidelobe level. The deployment of the proposed passive radar is flexible and scalable, and it is based on multichannel software defined radio receivers that obtain the reference and surveillance signals by means of digital beamforming. The signal processing and data fusion are based, respectively, on the delay-Doppler cross-correlation with the reconstructed reference signals and a two-stage tracking at sensor and central level. Finally, the performance of the proposed system is estimated in terms of its maximum detection range and simulation results of the detection of moving targets are presented, demonstrating its technical feasibility for the short-range detection of pedestrians, vehicles, and small drones.

This work describes the design of a rectenna array exploiting orthogonal, closely-spaced UHF monopoles for orientation-independent RF energy harvesting to energize a passive tag, designed for UWB localization, with wake-up radio (WUR) capabilities. To reach this goal, different RF networks are studied to simultaneously realize RF decoupling of the antenna elements and matching of the radiating elements to the non-linear network of rectifiers. The design is performed for a wide power range of the RF incoming signals that need to be exploited for both energizing the passive tag and for providing energy autonomy to a WUR sub-system, used to minimize the long-term power consumption during tag standby operations. Two meandered cross-polarized monopoles, located in close proximity, and thus highly coupled, are adopted for orientation-insensitive operations. The combining RF network is reactive and includes an unbalanced power divider to draw a fraction of the harvested energy to a secondary way for WUR operations. The performance of the harvester is first optimized by EM/non-linear co-design of the whole system over an interval of low RF power levels. The system has been realized and experimentally validated: the superior results obtained, in terms of both dc voltage and power, with respect to a standard single-monopole rectenna, justify the deployment of the presented tag for the energy autonomy of future generation radio-frequency identification tags for indoor localization.

This paper describes a method to analyze open or closed elliptical structures with constant axial ratio by a Body-of-Revolution (BoR) Finite Element Method (FEM). The method is based on Transformation Optics, a coordinate transformation that maps the elliptical shape to a circular shape, for which BoR-FEM represents a greatly efficient tool for the analysis.

A compact low-pass filter (LPF) with wide rejection band based on T-type circuit of an enhanced dual composite right-/left-handed (D-CRLH) resonator is presented in this paper. The resonator has only one cell with series and parallel tank circuit. The parallel LC tank circuit has been realized by an interdigital capacitor and one shorted finger, whereas its series LC tank circuit is realized by an air gap capacitance and a short circuit stub. The filter has wide rejection band bandwidth with three transmission zeros (TZs). The filter bandwidth and TZs frequencies are controlled by the D-CRLH element values. The results of the proposed filter demonstrate minimum insertion loss in passband, high roll-off rate, and good figure of merit. The measured results are in good agreement with the simulated results. The detailed filter design is discussed in terms of circuit modeling, dispersion analysis, and full-wave simulation. Finally, the filter size is compact (0.10 λg × 0.15 λg) at cut-off frequency.

In this paper, based on a novel multimode stub-loaded resonator, a second-order quad-band bandpass filter (BPF) with mixed electric and magnetic coupling is presented. The electric coupling and magnetic coupling are realized by arranging the parallel coupled lines and the grounded stub, respectively. Eight controllable resonant modes can be simultaneously excited and easily tuned. Eight transmission zeros are created, enhancing the passband selectivity. In addition, the bandwidths can be controlled independently by adjusting the coupling strength. A quad-band BPF centering at 0.67, 1.51, 2.84, 3.58 GHz with respective 3 dB fractional bandwidths of 13.4, 15.6, 9.2, 11.5% is designed, fabricated, and measured. The filter is compact with overall size 0.058λg × 0.13λg. The measured results show a good consistence with the simulated ones.

The spectral congestion in existing Industrial, Scientific, and Medical (ISM) Wireless Local Area Network (WLAN) bands has led to the emergence of new ISM bands (Unlicensed National Information Infrastructure (UNII)) from 5.150 to 5.710 GHz. In this paper, a simple uniplanar, high gain, microstrip antenna is designed, fabricated, and tested for existing WLAN and new UNII standards. The proposed antenna provides dualband operation by joining two rectangular rings and cutting Defected Ground Structure in the Coplanar Wave Guide (CPW) feed. The experimental and simulation results show good return loss characteristics and stable radiation pattern over the desired frequency bands ranging from 2.20 to 2.65 GHz (WLAN band) at a lower frequency and from 5.0 to 5.45 GHz (UNII-1/UNII-2 bands). The measured peak gains are 5.5 and 4.9 dBi at 2.45 GHz (WLAN band) and 5.15 GHz (UNII band), respectively.

A new circularly polarized microstrip array antenna using the orthogonal feed technique is proposed in this paper. The antenna has a multi-layer structure and a new 3-way power divider employing the both-sided microwave integrated circuit technology is designed to configure the feed network of the array. Circular polarization (CP) is realized by creating a quadrature phase difference between orthogonal feed circuits of the patches. The multi-layer structure gives flexibility to adjust the patch spacing that helps to reduce the sidelobe level of the antenna. It is found that the multi-layer structure exhibits a gain of about 2 dB higher than that of a single layer structure by means of sidelobe reduction. The proposed structure also exhibits good CP performances that are verified by a good agreement of measured and simulated results. Simple and compact structure makes the antenna suitable for various wireless applications.