Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-25T19:12:39.009Z Has data issue: false hasContentIssue false
  • English
  • Français

Low-cost thin-film passive RFID circuits and detector system

Published online by Cambridge University Press:  06 January 2020

Salma El-Sawy Open the ORCID record for Salma El-Sawy [Opens in a new window] ,
Wasim Nawaz Open the ORCID record for Wasim Nawaz [Opens in a new window] ,
Mohamed Osama  and
Ahmet Tekin
Salma El-Sawy*
Affiliation:
Özyeğin University, OZU-X Building, Istanbul, Turkey
Wasim Nawaz
Affiliation:
Özyeğin University, OZU-X Building, Istanbul, Turkey
Mohamed Osama
Affiliation:
Özyeğin University, OZU-X Building, Istanbul, Turkey
Ahmet Tekin
Affiliation:
Özyeğin University, OZU-X Building, Istanbul, Turkey
*
Author for correspondence: Salma El-Sawy, E-mail: [email protected]
Get access Rights & Permissions [Opens in a new window]

Abstract

This paper discusses the design of chip-less RFID tags of a standard pocket size of 69 mm by 156 mm. These tags are based on lumped elements of copper metal traces constructed on a thin polyamide flexible substrate. Moreover, a low-cost single-chip Bluetooth detector circuit system is demonstrated. Two different detection methods: variable coil load coupling and optical light intensity detection were combined to yield 256 unique ID codes. In the first method, by utilizing simple 4 MHz digital drivers and an integrated analog to digital converter (ADC) in the reader controller; various inductively coupled resonant loads corresponding to multiple distinct tags could be differentiated, yielding eight different (3-bit) ID codes. The additional via-based hole pattern reflectometer method creates additional 32 distinct levels (5-bit) utilizing 650 nm visible light-emitting diode and a simple trans-impedance operational along with the same analog ADC pins of a Bluetooth controller. The printed circuit board trace coil on the two-layer low-cost FR-4 waterproof sealed detector unit is simultaneously used as a Qi wireless power receiver to charge the120 mAh 2450 Lithium Polymer (LiR) battery. The device could remain operational for more than a month with a single charge; remaining connected with a mobile device and enabling 10 readouts daily.

Keywords

Low costmutual inductancepassive RFIDplanar finger capacitanceplanar spiral inductancereader circuitwireless charger
Type
Industrial and Engineering Papers
Information
International Journal of Microwave and Wireless Technologies , Volume 12 , Issue 5 , June 2020 , pp. 356 - 366
Copyright
Copyright © Cambridge University Press and the European Microwave Association 2020

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Finkenzeller, K (2010) RFID Handbook: Fundamentals and Applications in Contactless Smart Cards, Radio Frequency Identification and Near-Field Communication. UK: John Wiley & Sons.CrossRefGoogle Scholar
2.Karmakar, NC, Roy, SM, Preradovic, S, Vo, TD and Jenvey, S (2006) Development of low-cost active RFID tag at 2.4 GHz. Microwave Conference, 2006. 36th European, IEEE, pp. 1602–1605.CrossRefGoogle Scholar
3.Silva, PM, Sousa, FR and Plett, C (2018) On–Chip Automatic LC Tuner for RFID Tags Based on Negative Resistances. IEEE Transactions on Circuits and Systems II: Express Briefs 65, 1029–1033.CrossRefGoogle Scholar
4.Preradovic, S, Karmakar, NC and Balbin, I (2008) RFID transponders. IEEE Microwave Magazine 9, 90–103.CrossRefGoogle Scholar
5.Kisic, M, Dakic, B, Damnjanovic, M, Menicanin, A, Blaz, N and Zivanov, L (2013) Design and simulation of 13.56 MHz RFID tag in ink-jet printing technology. pp. 263–267, 05.Google Scholar
6.Dakic, B, Damnjanovic, M, Zivanov, L, Menicanin, A, Blaz, N and Kisic, M (2012) Design of RFID antenna in ink-jet printing technology. Intelligent Systems and Informatics (SISY), 2012 IEEE 10th Jubilee International Symposium on, IEEE, pp. 429–432.CrossRefGoogle Scholar
7.Herrojo, C, Mata-Contreras, J, Paredes, F and Martın, F (2017) Near-field chipless RFID encoders with sequential bit reading and high data capacity. Microwave Symposium (IMS), 2017 IEEE MTT-S International, IEEE, pp. 1564–1567.CrossRefGoogle Scholar
8.Benamara, M, Grzeskowiak, M, Diet, A, Conessa, C, Lissorgues, G and Le Bihan, Y (2018) Effect of added resonators in RFID system at 13.56 MHz. IET Microwaves, Antennas & Propagation 12, 684–691.CrossRefGoogle Scholar
9.Preradovic, S and Karmakar, NC (2010) Design of chipless RFID tag for operation on flexible laminates. IEEE Antennas and Wireless Propagation Letters 9, 207–210.CrossRefGoogle Scholar
10.Mukherjee, S (2007) Chipless radio frequency identification by remote measurement of complex impedance. Microwave Conference, 2007. European, IEEE, pp. 1007–1010.CrossRefGoogle Scholar
11.Hota, M, Bera, M and Maiti, C (2012) Flexible metal–insulator–metal capacitors on polyethylene terephthalate plastic substrates. Semiconductor Science and Technology 27, 105001.CrossRefGoogle Scholar
12.Meena, JS, Chu, M-C, Kuo, S-W, Chang, F-C and Ko, F-H (2010) Improved reliability from a plasma-assisted metal-insulator-metal capacitor comprising a high-k hfo 2 film on a flexible polyimide substrate. Physical Chemistry Chemical Physics 12, 2582–2589.CrossRefGoogle ScholarPubMed
13.Blaž, N, Kisić, M, Žlebič, Č, Marić, A and Živanov, L (2016) Capacitance variation of inkjet printed interdigital capacitor by structure bending. Electronics Technology (ISSE), 2016 39th International Spring Seminar on, IEEE, pp. 506–509.CrossRefGoogle Scholar
14.Huang, G-L, Sim, C-Y-D, Liang, S-Y, Liao, W-S and Yuan, T (2018) Low-profile flexible UHF RFID Tag design for wristbands applications. Wireless Communications and Mobile Computing 2018, Article ID 9482919, 13 pages.CrossRefGoogle Scholar
15.Jang, H, Lim, W, Oh, K, Moon, S and Yu, J (2010) Design of low-cost chipless system using printable chipless tag with electromagnetic code. IEEE Microwave and Wireless Components Letters 20, 640–642.CrossRefGoogle Scholar
16.Sheeparamatti, BG, Hanasi, PD, Aibbigeri, V and Meti, N (2015) Study of capacitance in electrostatic comb-drive actuators. In Excerpt from the Proceedings of the COMSOL Conference in Pune.Google Scholar
17.Igreja, R and Dias, C (2004) Analytical evaluation of the interdigital electrodes capacitance for a multi-layered structure. Sensors and Actuators A: Physical 112(2–3), 291–301.CrossRefGoogle Scholar
18.Khan, AM and Reddy, M (2016) Design and optimization of interdigital capacitor. International Journal of Research in Engineering and Technology 5, 73–78.Google Scholar
19.Mohan, SS, del Mar Hershenson, M, Boyd, SP and Lee, TH (1999) Simple accurate expressions for planar spiral inductances. IEEE Journal of Solid-State Circuits 34, 1419–1424.CrossRefGoogle Scholar
20.Nair, R, Barahona, M, Betancourt, D, Schmidt, G, Bellmann, M, Höft, D, Plettemeier, D, Hübler, A and Ellinger, F (2014) A fully printed passive chipless RFID tag for low-cost mass production. The 8th European Conference on Antennas and Propagation (EuCAP 2014), The Hague.CrossRefGoogle Scholar
21.Yuan, M, Ghannam, R, Karadimas, P and Heidari, H (2018) Flexible RFID Patch for Food Spoilage Monitoring. In 2018 IEEE Asia Pacific Conference on Postgraduate Research in Microelectronics and Electronics (PrimeAsia), pp. 68–71. IEEE.CrossRefGoogle Scholar