Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-25T23:02:43.275Z Has data issue: false hasContentIssue false
  • English
  • Français

Additive technology applied to the realization of K-band microwave terminations: reproducibility improvement

Published online by Cambridge University Press:  30 April 2018

Azar Maalouf ,
Ronan Gingat  and
Vincent Laur
Azar Maalouf
Affiliation:
Lab-STICC, Université de Bretagne Occidentale, 6 avenue Victor le Gorgeu, 29238, Brest Cedex 3, France
Ronan Gingat
Affiliation:
Lab-STICC, Université de Bretagne Occidentale, 6 avenue Victor le Gorgeu, 29238, Brest Cedex 3, France
Vincent Laur*
Affiliation:
Lab-STICC, Université de Bretagne Occidentale, 6 avenue Victor le Gorgeu, 29238, Brest Cedex 3, France
*
Corresponding author: V. Laur Email: [email protected]
Get access Rights & Permissions [Opens in a new window]

Abstract

This study examines K-band rectangular waveguide terminations with three-dimensional (3D)-printed loads, and proposes an Asymmetrical Tapered Wedge topology. This geometry shows a good tradeoff between microwave performance and 3D-printing issues (printing directions and support material requirements), thus improving noticeably the reproducibility of the devices. The effect of the density of the 3D-printed load on the reflection parameter of the termination was investigated. Even for a low density, reflection level remained below −27.5 dB between 18 and 26.5 GHz. Reproducibility was demonstrated by the characterization of six loads that were 3D printed under the same conditions. Measurements demonstrate that a maximum reflection parameter level of −33.5 dB can be ensured over the whole frequency band without any post-machining of the 3D-printed devices.

Keywords

Passive components and circuitsMicrowave measurements
Type
Research Papers
Information
International Journal of Microwave and Wireless Technologies , Volume 10 , Special Issue 1: Journee Nationale des Micro-ondes 2017 , February 2018 , pp. 3 - 8
Copyright
Copyright © Cambridge University Press and the European Microwave Association 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1]Liang, M.; Xiaoju, Y.; Shemelya, C.; Mac Donald, E.; Hao, X.: 3D printed multilayer microstrip line structure with vertical transition toward integrated systems, in IEEE Int. Microwave Symp., Phoenix, AZ, 2015.Google Scholar
[2]Squires, A.D.; Constable, E.; Lewis, R.A.: 3D printing of aspherical terahertz lenses and diffraction gratings, in Int. Conf. Infrared Millimeter Terahertz waves, Tucson, AZ, 2014.Google Scholar
[3]Vera-Lopez, A.L.; Rojas-Nastrucci, E.A.; Cordoba-Erazo, M.; Weller, T.: Ka-band characterization and RF design of Acrynolitrile Butadiene Styrene (ABS), in IEEE Int. Microwave Symp., Phoenix, AZ, 2015.Google Scholar
[4]Rojas-Nastrucci, E.A.; Weller, T.; Lopez Aida, V.; Fan, C.; Papapolymerou, J.: A study on 3D-printed coplanar waveguide with meshed and finite ground planes, in IEEE Wireless Microwave Technology Conf., Tampa, FL, 2014.Google Scholar
[5]Deffenbaugh, P.I.; Rumpf, R.C.; Church, K.H.: Broadband microwave frequency characterization of 3-D printed materials. IEEE Trans. Comp. Pack. Manufact. Tech., 3 (2013), 2147–2155.Google Scholar
[6]Arbaoui, Y.; Laur, V.; Maalouf, A.; Queffelec, P.: 3D printing for microwave: materials characterization and application in the field of absorbers, in IEEE Int. Microwave Symp., Phoenix, AZ, 2015.Google Scholar
[7]Arbaoui, Y. et al. : Full 3D printed microwave termination: a simple and low cost solution. IEEE Trans. Micr. Th. Techn., 64 (2015), 271–278.Google Scholar
[8]Nazoa, N.; Ridler, N.: LA19-13-02 3 GHz VNA calibration and measurement uncertainty, LA Techniques, Technology Note LAP03 v2.0, 2007.Google Scholar
[9]Leite, M.; Varanda, A.; Silva, A.; Relogio Ribeiro, A.; Vaz, F.: Water absorption and mechanical properties evaluation of surface modified ABS printing parts, in Int. Conf. on Progress In Additive Manufacturing, Singapore, 2016.Google Scholar