The oxygen isotopes of albite, quartz, and zeolites from the Hokonui Hills, New Zealand, constrain crystallization temperatures and the type of pore fluids present during diagenesis. A section of altered vitric tuffs in this region contains an extremely sharp reaction boundary between a heulandite-chlorite assemblage containing fresh detrital plagioclase and a laumontite-albite-quartz assemblage. A laumontite vein follows the local joint pattern and forms the reaction boundary, suggesting that laumontitization occurred as a result of fracturing and increased fluid flow during uplift. The albite (δ18O = +15.0)-quartz (δ18O = +19.9 to +20.5) geothermometer constrains the temperature of alteration between 145° and 170°C with a pore water δ18O of +1.8 to +3.5. The tuff was buried to an estimated maximum temperature of about 225°C, indicating that alteration occurred after maximum burial.

Framework oxygen was extracted from zeolites by reaction with ClF3 after the zeolites were thermally dehydrated in a vacuum. Laumontite was dehydrated at 300°C, and stilbite at 150°C. The precision of the method is typically about ±0.45‰. Fractionation curves for dehydrated zeolites are based on a general expression from the literature for feldspars, which depends only on the Si/Al ratio of the mineral. Measured δ18O values for laumontite in the groundmass of the altered tuff were +14.4‰. The laumontite-quartz pair constrains the temperature to between 139° and 162°C, in excellent agreement with the albite-quartz pair, and supporting the petrographic observation of co-crystallizing albite-laumontite.

Oxygen isotope values for fracture-filling laumontite in the vitric tuff, as well as those for groundmass and vein laumontite from other parts of the stratigraphic section, cluster around +14.5, suggesting that laumontite probably crystallized under similar conditions throughout much of the section. Oxygen isotope values for stilbite veins from various parts of the section indicate that this mineral crystallized at lower temperatures than the laumontite, for a given fluid isotopic composition, in agreement with the observed cross-cutting of laumontite by stilbite.

The mineralogy of the clay fraction was studied for soils and saprolite on two Blue Ridge Front mountain slopes. The clay fraction contained the weathering products of primary minerals in the mica gneiss and schist parent rocks. Gibbsite is most abundant in the saprolite and residual soil horizons, where only chemical weathering has been operable. In colluvial soil horizons, where both physical and chemical weathering have occurred, the clay fraction consists largely of comminuted primary phyllosilicates —muscovite, chlorite, and possibly biotite—and their weathering products: vermiculite, interstratified biotite/vermiculite (B/V), and kaolinite. The clay-size chlorite contains Fe2+ as indicated by Mössbauer spectroscopy, and is more resistant to weathering than biotite. The vermiculite and B/V, both weathering products of biotite, contain Fe3+. Vermiculite in colluvial soils and, especially, surface horizons is weakly hydroxy-interlayered. The kaolinite in the clay fraction resulted at least partly from the comminution of kaolinized biotite in coarser fractions.

The hematite content ranged from 0 to 8% of the clay fraction and strongly correlates (r =.95) with dry clay redness, as measured by the redness rating: RR = (10 - YR hue) × (chroma) ÷ (value). The hematite is largely a product of the weathering of almandine; thus, the soil redness is dependent on the amount of almandine in the parent materials and its degree of weathering in the soils. Goethite (13–22% of the clay fraction) imparts a yellow-brown hue to soils derived from almandine-free parent rocks. The release of Fe in relatively low concentrations during the weathering of Fe-bearing primary minerals, particularly biotite, appears to have promoted the formation of goethite.

Cementing materials in the Arahama sand dune, Japan, were studied mineralogically and biogeochemically to gain a better understanding of the cause of hardening. The cementing material is a clay-organic complex composed of noncrystalline gels and a matrix of small, poorly crystalline particles showing 14–16-Å spacings. The gel materials appear to have transformed into the poorly crystalline particles, which have a high carbon content and Al/Si ratios of 2.2 to 2.0. These particles are slightly richer in Si and poorer in Fe than the gel materials themselves. The organic portion of the complex can be removed by H2O2 treatment, leaving a noncrystalline network-structure containing a dispersed granular component. Scanning auger-depth profiles of individual particles show a high surface concentration of C and O and an increase in the Al/Si ratio with depth. The energy-intensity distribution suggests a mixture of carbon compounds having a major core-line binding energy of a hydrocarbon. The gel-cementing materials in the sand dune may have been formed from biochemical weathering products of organic matter, which subsequently controlled the formation of clay-organic complexes.

The catalytic power of Ca-nontronite, Ca-bentonite, and Ca-kaolinite in promoting the abiotic ring cleavage of pyrogallol (1,2,3-trihydroxybenzene) and the associated formation of humic polymers was studied in systems free of microbial activity. The presence of Ca-kaolinite and especially Ca-nontronite in the pyrogallol solutions at pH 6.00 greatly enhanced the absorbance at both 472 and 664 nm of the supernatants. At an initial pH of 6.00 and at the end of a 90-hr reaction period, the amounts of CO2 released from the ring cleavage of pyrogallol and the yields of the resultant humic polymers formed in the reaction systems followed the same sequence: Ca-nontronite > Ca-kaolinite > Ca-bentonite. The data indicate that the catalytic power of Fe(III) on the edges and in the structure of nontronite was substantially greater than that of Al on the edges of kaolinite and montmorillonite and of a small amount of Fe(III) in the structure of montmorillonite in promoting the reactions. The infrared and electron spin resonance spectra and the solid-state, cross-polarization magic-angle-spinning 13C nuclear magnetic resonance spectra of humic polymers formed in the reaction systems resembled those of natural humic substances.

The layer charge of five smectites, one vermiculitic material, and five reduced-charge clays was determined by the alkylammonium and structural formula methods. The two sets of results were found to be linearly correlated (r =.961); however, the values that were determined by the alkylammonium method were 20 to 30% lower than those determined by the structural formula method, and the regression slope for their linear relationship was 1.67. The fact that the structural formula method includes the effects of cations on the lateral edges of the clay particles probably accounted for some of the differences in the magnitude of the results but should not have caused the regression slope to deviate substantially from 1.00. Therefore, inaccurate estimates of the packing density of alkylammonium cations in the interlayer space of 2:1 phyllosilicates were deemed responsible for the systematic divergence of the results of the two methods. To satisfy the need for a relationship between the two methods of determining layer charge, an empirical means of adjusting the alkylammonium values has been proposed and shown to yield values of layer charge that are comparable to those determined by the structural formula method.

The migration of interlayer Fe3+ cations into the structure of heated montmorillonite and Laponite has been studied by electron spin resonance (ESR), Mössbauer spectroscopy, and magnetic susceptibility measurements. The intensity of the ESR signal corresponding to interlayer Fe3+ in air-dried montmorillonite and Laponite increased linearly as the amount of interlayer Fe3+ increased. Changes in the spectra after thermal treatment indicate that Fe3+ cations migrated into the pseudohexagonal cavities of dehydrated montmorillonite and Laponite. The electrostatic interaction between the Fe3+ and the oxygen atoms defining the entrance to these cavities and the proton of the structural OH groups at the bottom of the cavities differ for the two smectites. Ferric cations were apparently bound more strongly within the pseudohexagonal cavities of the dehydrated montmorillonite than within the cavities of Laponite, because the montmorillonite did not rehydrate after heating. The differences in the binding of Fe3+ cations within the pseudohexagonal cavities of montmorillonite and Laponite were probably due to variations in the ability of the protons of the structural OH groups to reorient. An additional electronic interaction occurred in the heated Laponite, in which small cations were able to promote the formation of structural defects, which gave rise to a sharp ESR signal at g = 2.00. No evidence for the penetration of Fe3+ cations into the vacant octahedral sites of montmorillonite was found.

X-Ray powder diffraction and thin section analyses indicate that marginal lacustrine mudstones of the Green River Formation in the south-central Uinta basin, Utah, contain abundant analcime. The analcime has a low Si/Al ratio (<2.31) and occurs as very fine grained disseminated crystals and, to a lesser extent, as coarser-grained pore-filling cement. Analcime-rich mudstones and associated sandstones, siltstones, and carbonates lack volcanic detritus and zeolites other than analcime, thus making it difficult to support the concept that the analcime formed from precursor zeolites derived from volcanic glass altered in saline, alkaline-lake water. Abundant dolomite, syneresis cracks, and the absence of freshwater pelecypods and gastropods suggest that the lake (Lake Uinta) was moderately saline and alkaline. The restricted illite-illite/smectite clay mineral suite in the analcime-rich mudstones suggests that detrital clays significantly altered in a moderately saline and alkaline environment, thereby providing a source of Si and Al for the formation of analcime.

Red mudstones contain twice as much analcime as green mudstones (14 vs. 7 wt. %). Green mudstones have a day mineral suite consisting of illite (44 wt. %), mixed-layer illite/smectite (35 wt. %), smectite (12 wt. %), and minor kaolinite (4 wt. %) and chlorite (5 wt. %), whereas red mudstones have a more restricted day mineral suite consisting ofillite (68 wt. %) and mixed-layer illite/smectite (26 wt. %) with very minor smectite, chlorite, and kaolinite. Periodic minor fluctuations in lake level probably exposed large areas of shallow lacustrine-interdistributary green mud. Evaporative pumping on the exposed mudflats concentrated the moderately saline and alkaline-lake water, thereby producing Na-rich brines that enhanced the formation of analcime by accelerating the alteration of detrital clays and, perhaps, other minerals. Oxidation of iron from altered iron-bearing minerals stained the analcime-rich mud red with iron hydroxide or oxide (perhaps hematite). The overall reaction from green to red mud (mudstones) was probably: detrital phyllosilicates + Na-brine + iron-bearing minerals + oxygen → analcime + iron hydroxide or iron oxide.

The validity of the saddle/001 method for estimating the percentage of smectite layers in randomly interstratified illite/smectite (I/S) minerals as a routine laboratory technique has been examined with respect to the effects of the crystallite size distribution (N = number of layers) of I/S and the degree of preferred orientation of crystallites in the prepared specimen. X-ray powder diffraction experiments of I/S clays indicated that the crystallite size distribution was 3 < N < 12; these values were supported satisfactorily by the variation of the d(002) value of the samples. An analysis of the Lorentz factor concerning the degree of preferred orientation of crystallites indicated that a calibration curve calculated using the random powder Lorentz factor and the above crystallite size distribution fit the data better than an assumption of perfect orientation. Consequently, if a calibration curve of the saddle/001 ratio is used to estimate the percentage of smectite layers in I/S, an error of 10–15% should be expected from the variable crystallite size distribution of actual samples, in which I/S dominates over other phyllosilicate phases that give reflection between 10–14 Å. This method is useful, however, in estimating the relative percentage of smectite layers in randomly interstratified I/S for samples examined under identical experimental conditions.

X-ray powder diffraction (XRD) and energy-dispersive X-ray analyses (EDX) of individual clay particles from hydrothermal mounds in the Galapagos spreading center (GSC) (Deep Sea Drilling Project, hole 509B) and high-resolution transmission electron microscopy (HRTEM) of the <2-µm size fraction of these sediments were carried out to document the mineralogy, geochemistry, and evolution of their clay horizons. The hydrothermal clay minerals of the GSC mounds were found to be intercalated with pelagic sediments and occurred as irregular interstratified illite/smectite according to X-ray powder diffraction analyses. On the basis of TEM, HRTEM, and EDX data, two types of clays appeared to coexist; these types differed in morphology, potassium content, and mode of stacking sequence. Lath-shaped particles having regular 10-Å, spacings were identified as glauconite, and filmy or veil-like particles, having curly edges and variable 10-13-Å spacings were identified as Fe-smectite (nontronite and Fe-montmorillonite). The absence of lattice fringes between Fe-smectite and glauconite crystallites was observed by HRTEM in clay aggregates. This structural discontinuity between Fe-smectite and glauconite layers suggests that a dissolution-recrystallization mechanism was responsible for the textural and chemical transition from the filmy Fe-smectite to the lath-like glauconite.

A kaolinite-pyridine intercalation compound was prepared using hydrated kaolinite as an intermediate. Hydrated kaolinite having a basal spacing of 10 Å was treated with pyridine to form a well-ordered intercalation compound having a basal spacing of 12.0 Å. Infrared spectroscopy indicated the presence of hydrogen bonding between the hydroxyls of the kaolinite and the pyridine. 29Si nuclear magnetic resonance spectroscopy with cross polarization and magic-angle spinning revealed that intercalated pyridine affected the environment of silicon. The mono-substituted pyridine derivatives were also intercalated with hydrated kaolinite. On the basis of the basal spacings of the intercalation compounds and the stabilities of the derivatives between the layers, the pyridine appeared to be in an approximately perpendicular position, with the nitrogen facing the gibbsitic sheets.

Mn-substituted iron oxides were synthesized by coprecipitating Fe(NO3)3 and Mn(SO4) solutions with NH4OH, adjusting the suspensions to pH 4 or 6, and then keeping the suspensions at 55°C for 62 days. The Mn mole fraction of the final products ranged from 0 to 0.3. X-ray powder diffraction patterns showed that goethite and hematite formed in each Fe-containing system. Groutite formed in systems having initial Mn mole fractions ≥0.35. Only manganite and hausmannite formed in the pure Mn systems. The oxalate-soluble Fe in the samples increased as the Mn mole fraction increased and was slightly larger for the pH 6 series.

For samples that contained the largest Mn mole fraction, the b and c dimensions of the goethite unit cell were shifted toward those of groutite, and the b and c dimensions of the groutite unit cell were shifted toward those of goethite. Assuming the Vegard rule holds for the unit-cell c dimension, the goethite accommodated a maximum Mn mole fraction of 0.34, and the groutite accommodated a maximum Fe mole fraction of 0.31. The unit-cell dimensions of hematite did not vary systematically with the mole fraction of Mn in solution, probably because little Mn substituted into the hematite structure.

Adsorption of p-hydroxybenzoate anion on synthetic Fe oxides, hydroxides, and oxyhydroxides (hereafter referred to as oxides) was measured at pH 5.5, and the organic-oxide interaction was characterized using diffuse-reflectance Fourier-transform infrared (DRIFT) spectroscopy. Surface complexes with ferrihydrite, hematite, goethite, and noncrystalline Fe oxide were investigated. Infrared (IR) spectra of the oxides after separation from p-hydroxybenzoate solutions showed the organic to be coordinated by an inner-sphere mechanism to the oxide surface through the carboxylate group. Bidentate binding of the carboxylate was identified to be the dominant type of complexation on the oxides. Although the IR study suggested that goethite formed the strongest surface iron-carboxylate bond, the total amount of organic adsorbed was the least on this oxide. This result suggested that bond energy was less important than adsorption site density in determining the amount of organic anion adsorption. Increasing ionic strength had little effect on adsorption by the noncrystalline Fe oxide, but dramatically decreased adsorption on hematite and goethite. This difference might have been due to anion competition for binding sites. At pH 5.5, the amount of organic adsorbed per unit weight of oxides (in 0.05 M NaClO4) followed the order: ferrihydrite > noncrystalline Fe oxide > hematite ≫ goethite. Adsorption per unit of surface area however, followed the order: ferrihydrite > hematite > noncrystalline Fe oxide ≫ goethite. The hematite adsorption reaction appeared to be driven by entropy, inasmuch as the reaction was endothermic. The difference among the oxides in surface reactivity toward p-hydroxybenzoate is hypothesized to have been caused by differences in both quantity and structural arrangement of reactive sites on the oxide surface.

A study was carried out on the influence of the sequence of addition of montmorillonite, hydroxy-Al ions, and tannic acid ([Al] = 0.015 M; 6 mmole Al/g of clay; tannic acid/Al molar ratio = 0.1) on the nature of organo-clay complexes formed at pH 4.5. A negligible amount of tannate was held on the clay surfaces in the absence of Al, whereas in the presence of Al, hydroxy-Al-tannate species were easily adsorbed on clay surfaces. Their distribution on the external surface and in the interlayer space of montmorillonite, however, was a consequence of how the components reacted with each other. The complexes showed broad X-ray powder diffraction peaks at 15.6 to 19.2 Å at room temperature. They also showed different behavior to preheating, ethylene glycol solvation, and chemical treatments. Whereas tannic acid showed two prominent exothermic peaks at 390° and 510°C, all hydroxy-Al-tannate-mont-morillonite complexes showed a broad exotherm at about 400°–450°C. Some complexes showed, in addition, a small inflection between 350° and 420°C. The complexes also showed distinct differences in cation-exchange capacity, carbon content, extractable Al, titratable acidity, and mode of aggregation after drying.

Transmission electron microscope (TEM) images of mixed-layer illite/smectite (I/S) from Gulf Coast shales obtained earlier by the authors have been reexamined by comparing them with the calculated images of G. D. Guthrie and D. R. Veblen. Ordered two-layer periodicity was not detected in the 1750- and 2450-m depth samples, for which X-ray powder diffraction (XRD) showed 20% and 40% illite randomly interstratified in I/S, respectively. Two-layer periodicities that occur in images of the 5500-m depth sample were inferred to reflect ordered I/S. XRD data for the same sample imply the presence of 80% illite in RI-ordered I/S. The two-layer periodicities were observed in slightly overfocused images, consistent with the image calculations of Guthrie and Veblen, with strong dark fringes inferred to correspond to smectite interlayers. Two-layer periodicities were observed only in small domains of a few of the images, consistent with the requirement of special orientation of layers, which varies continuously over a wide range. The lack of more frequent observations of ordered periodicities in TEM images may reflect the lack of the special observation conditions and chemical heterogeneity of illite and smectite layers. Ordered mixed-layering may exist in those specimens for which XRD indicates such ordering, in contrast to the previous interpretation of the authors.

A method using a finite, first-order Markov chain is presented to estimate rate constants for zeolite formation from experimental nuclear magnetic resonance (NMR) data on the abundance of different silica oligomers. An experimental design is suggested by which this method can be implemented. The method uses weighted least squares to estimate transition probabilities from aggregate NMR data. Rate constants, equilibrium constants, and free energies of elementary zeolite-forming reactions can be estimated. Hypothetical zeolite-forming reactions can also be modeled. An example of modeling, using hypothetical data, shows how zeolite formation can result from reactions involving mainly silica cyclic tetramers.

Perlite, which occurs at the contacts between dacite and lacustrine tuffs of Miocene age in the Guryongpo area, Korea, has undergone more sluggish and incomplete diagenetic alteration than the surrounding zeolitic tuffs. Alkali-clinoptilolite, mordenite, smectite, K-rich gel-like glass, low-cristobalite, and K-feldspar are characteristic diagenetic phases in the altered perlite.

Hydration of the glass to form perlite resulted in the expulsion of cations, mainly Na, from the glass into the pore fluid and in the relative enrichment of K in the perlite. Hydration of the glass also resulted in increased alkalinity of the pore fluid, which, in turn, affected the nature and behavior of subsequent glass dissolution. Textural observations and chemical data on the early diagenetic phases indicate a sequence of incongruent dissolution reactions, which depended on silica activity and alkalinity of the ambient pore fluid: Reaction (1) 12.5 perlitic glass + 3.88 K+ + 0.65 H+ + 15.4 H20 = smectite + 9.5 gellike glass + 4.03 Na+ + 0.25 Ca2+ + 10.55 H4SiO4 released Ca and silica which were consumed by reaction (2) perlitic glass + 0.1 Ca2+ + 0.1 H4SiO4 + 0.1 H+ + H20 = clinoptilolite + 0.1 K+ + 0.2 Na+. The paragenesis from glass via smectite to alkali zeolites in most glass-bearing rocks may be explained by a sequence of such dissolution reactions. Still later reactions involved the transition from less-silicic clinoptilolite to an assemblage of silicic Na-clinoptilolite + mordenite and the crystallization of the gel-like glass to K-feldspar.

The interaction between N-methyl 8-hydroxy quinoline methyl sulfate, a drug that absorbs erymathogenic near-ultraviolet radiation, and smectite was studied by X-ray powder diffraction (XRD) and adsorption and desorption techniques. From the adsorption studies, (1) the amount of the drug adsorbed by Na-smectite increased with the pH of the solution to pH 6.5 and then decreased as the pH was further increased; (2) the maximum amount adsorbed at pH 6.5 was 102 meq/100 g of clay; and (3) the maximum amount of drug adsorbed, according to the adsorption isotherms at pH 4, was close to the cation-exchange capacity of the smectite (80 meq/100 g). The XRD studies showed that the drug molecules were adsorbed in the interlayer space of smectite and that cation exchange was the chief mechanism responsible for these interactions. The results of the adsorption-desorption cycles of the drug by smectite showed that this clay is a good support for this compound. In addition, an alternative method was developed to obtain the intercalation compound to avoid the standard method of exchange by impregnation. The method consisted of grinding a mixture of the drug with the clay. The characteristics of the complex thus formed were similar to those of the complex formed by exchange at pH 4 to 7.

To gain insight into the pharmacological properties of the intercalation compound studied, its capacity for absorption of visible and near-ultraviolet light was investigated. The diffuse reflectance spectrum of the complex showed intense absorption bands, absent or weak in the spectra of the pure drug or the untreated clay, at 250, 290, and ~390 nm.

Phillipsite is a common constituent in diagenetically altered rhyolitic vitric tuffs of Cenozoic saline, alkaline-lake deposits where it occurs as spherulites or aggregates of prismatic crystals. This phillipsite has chemical and physical properties that differ from phillipsites that occur in rocks of other compositions and depositional environments, but previously it had not been completely characterized. Published analyses of five samples from four deposits in the southwestern United States show that the phillipsite is very siliceous and alkalic; the Si/(Al + Fe3+) ratio is 3.08–3.37, alkalis greatly exceed the divalent exchangeable cations, and the Na/K ratio is 1.05–3.05. The mean index of refraction (1.451–1.470) is much lower than that generally reported for the phillipsite group and can be correlated with the relatively high Si and alkali contents. Monoclinic unit-cell parameters show the following ranges: a = 9.931–9.991 Å, b = 14.142–14.155 Å, c = 8.650–8.706 Å, ß = 124.57–125.07°, and V = 1000.3–1007.4 Å3. The especially small b dimension is consistent with the high Si content.

The structural damage produced by dry grinding and acid leaching of chrysotile was studied by transmission and scanning electron microscopy, infrared spectroscopy, X-ray powder diffraction, and thermogravimetric analysis. Severe dry grinding converted the chrysotile fibers into fragments having strong potential basic reaction sites. These sites were immediately neutralized by molecules present in the atmosphere (e.g., H2O, CO2). Acid leaching transformed the chrysotile fibers into very porous, non-crystalline silica, which was easily fractured into short fragments. The damage produced in the chrysotile structure by grinding or leaching was assessed by monitoring the intensity of various infrared absorption bands.

The oxidation of 1,2- and 1,4-dihydroxybenzenes (1,2-DHB and 1,4-DHB) by unbuffered aerated suspensions of synthetic bimessite was studied by continuously monitoring the H+, Mn2+, dissolved O2, and organic radical concentration of the aqueous phase during the reaction. The reaction rapidly generated a very high pH, attributed to oxide dissolution, and the alkaline conditions prevented Mn2+ release into solution over the entire reaction period. Semiquinone radical anions accumulated early in the reaction and then diminished. A secondary radical product appeared in solution during the reaction of the oxide with 1,2-DHB, and was tentatively identified as an hydroxylated semiquinone. The oxide/DHB ratio controlled the maximum concentration and persistence of these radicals in solution as well as the degree to which O2 was consumed as an electron donor. In general, low oxide/DHB ratios promoted O2 uptake by the system, consistent with the subordinate role of O2 as a competing electron acceptor in the presence of excess Mn oxide. Soluble phosphate suppressed O2 consumption, but the mechanism by which it interacted with the reaction system was not determined.