The Blue Ice Drill (BID) is a large-diameter agile drill system designed by the Ice Drilling Design and Operations group of the University of Wisconsin–Madison to quickly core-clean 241 mm diameter ice samples from near-surface sites. It consists of a down-hole motor/gear reducer rotating a coring cutter and core barrel inside an outer barrel for efficient cuttings transport in solid ice. A variable-frequency drive and custom control box regulates electrical power to the drill. Torque reaction is accomplished on the surface via handles attached to a torsion stem. Core recovery is achieved with either core dogs in the sonde or with a separate core recovery tool. All down-hole tools are suspended on a collapsible tripod via ropes running on a capstan winch. The BID is operated by a minimum of two people and has been used successfully during two seasons of coring on a blue ice area of Taylor Glacier, Antarctica. An updated version of the drill system, BID-Deep, has been designed to recover cores to depths up to 200 m.

Supraglacial meltwater lakes trigger ice-shelf break-up and modulate seasonal ice-sheet flow, and are thus agents by which warming is transmitted to the Antarctic and Greenland ice sheets. To characterize supraglacial lake variability we perform a comparative analysis of lake geometry and depth in two distinct regions, one on the pre-collapse (2002) Larsen B ice shelf, Antarctica, and the other in the ablation zone of Paakitsoq, a land-terminating region of the Greenland ice sheet. Compared to Paakitsoq, lakes on the Larsen B ice shelf cover a greater proportion of surface area (5.3% cf. 1%), but are shallower and more uniform in area. Other aspects of lake geometry (e.g. eccentricity, degree of convexity (solidity) and orientation) are relatively similar between the two regions. We attribute the notable difference in lake density and depth between ice-shelf and grounded ice to the fact that ice shelves have flatter surfaces and less distinct drainage basins. Ice shelves also possess more stimuli to small-scale, localized surface elevation variability, due to the various structural features that yield small variations in thickness and which float at different levels by Archimedes’ principle.

VALKYRIE (Very-deep Autonomous Laser-powered Kilowatt-class Yo-yoing Robotic Ice Explorer) is a NASA-funded project to develop key technologies for an autonomous ice penetrator, or cryobot, capable of delivering science payloads through outer planet ice caps and terrestrial glaciers. This 4 year effort will produce a cylindrical cryobot prototype 280 cm in length and 25 cm in diameter. One novel element of VALKYRIE’s design is the use of a high-energy laser as the primary power source. 1070 nm laser light is transmitted at 5 kW from a surface-based laser and injected into a custom-designed optical waveguide that is spooled out from the descending cryobot. Light exits the downstream end of the fiber, travels through diverging optics, and strikes an anodized aluminum beam dump, which channels thermal power to hot-water jets that melt the descent hole. Some beam energy is converted to electricity via photovoltaic cells, for running on-board electronics and jet pumps. Since the vehicle can be sterilized prior to deployment, and forward contamination is minimized as the melt path refreezes behind the cryobot, expansions on VALKYRIE concepts may enable cleaner access to deep subglacial lakes. This paper focuses on laser delivery and beam dump thermal design.

Bed-reflection power (BRP) from ice-penetrating radar has been used to make inferences about subglacial conditions and processes, yet is subject to confounding influences, including englacial attenuation and bed geometry. We use radar data collected in 2008–11 from a polythermal glacier to compute BRP with the aim of relating BRP to basal conditions. We examine the relationship between raw BRP and ice thickness, apparent bed slope and thickness of the englacial scattering layer as a proxy for internal reflection power. We then analyze a corrected form of the BRP with a graph-segmentation algorithm to delineate areas of high and low reflection power. Low corrected BRP values are found near the glacier terminus where the bed is most likely to be cold, while high corrected BRP is found in the region thought to be undergoing a slow surge. We find a spatial correlation between high BRP and high values of subglacial hydraulic upstream area, suggestive of a hydrological control on BRP. Whereas in dominantly cold glaciers BRP seems to distinguish cold from temperate regions of the bed, BRP in a polythermal glacier with a substantial volume of temperate ice may be a more complex product of thermal and hydrological conditions.

Monitoring the glacier mass balance of summer-accumulation-type Himalayan glaciers is critical to not only assess the impact of climate change on the volume of such glaciers but also predict the downstream water availability and the global sea-level change in future. To better understand the change in meteorological parameters related to glacier mass balance and runoff in a glacierized basin and to assess the highly heterogeneous glacier responses to climate change in the Nepal Himalaya and nearby ranges, the Cryosphere Monitoring Project (CMP) carries out meteorological observations in Langtang Valley and mass-balance measurements on Yala Glacier, a debris-free glacier in the same valley. A negative annual mass balance of –0.89m w.e. and the rising equilibrium-line altitude of Yala Glacier indicate a continuation of a secular trend toward more negative mass balances. Lower temperature lapse rate during the monsoon, the effect of convective precipitation associated with mesoscale thermal circulation in the local precipitation and the occurrence of distinct diurnal cycles of temperature and precipitation at different stations in the valley are other conclusions of this comprehensive scientific study initiated by CMP which aims to yield multi-year glaciological, hydrological and meteorological observations in the glacierized Langtang River basin.

There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.

Ice sounding with radar is a well-established technique for the retrieval of ice depth, and provides information on ice structures and layering. Airborne radar ice sounders suffer from off-nadir surface clutter that masks the signal from bedrock and ice layers with unwanted but simultaneously received surface reflections. This is of importance for future satellite ice-sounding missions, as the spaceborne geometry leads to strong surface clutter even for deep subsurface returns. This paper presents analysis and comparison of different clutter-suppression techniques applied to data acquired with the European Space Agency's P-band POLarimetric Airborne Radar Ice Sounder (POLARIS). The 4 m long antenna of POLARIS enables simultaneous reception of up to four across-track channels. It was operated in 2011 over Antarctica at a high flight altitude of 3200 m. Different coherent weighting techniques of the receive channels were used to suppress the surface ‘clutter’. However, with a channel spacing of 1.4 times the wavelength, the grating lobe imposes a limitation to the off-nadir angular range in which clutter can be effectively attenuated. Results of ice sounding over Jutulstraumen glacier are described, where we demonstrate a clutter suppression of up to 10 dB.

The cone penetration test has been successfully used to classify soil for ∼100 years. However, it has received only limited contemporary use in frozen geomaterials. The historical and contemporary use of the cone penetration test in various frozen geomaterials is considered here and contemporary data from recent work in polar snow are examined. It is probable that many material physical properties (e.g. density, strength and microstructure) can be obtained directly from cone penetration testing. It appears under-utilized as a contemporary scientific and engineering investigative tool in frozen geomaterials.

A glacier-wide ice-thickness distribution and bedrock topography is presented for Starbuck Glacier, Antarctic Peninsula. The results are based on 90 km of ground-based radio-echo sounding lines collected during the 2012/13 field season. Cross-validation with ice-thickness measurements provided by NASA's IceBridge project reveals excellent agreement. Glacier-wide estimates are derived using a model that calculates distributed ice thickness, calibrated with the radio-echo soundings. Additional constraints are obtained from in situ ice flow-speed measurements and the surface topography. The results indicate a reverse-sloped bed extending from a riegel occurring ~ 5 km upstream of the current grounding line. The deepest parts of the glacier are as much as 500 m below sea level. The calculated total volume of 80.7 ± 7.2 km3 corresponds to an average ice thickness of 312 ± 30 m.

The proposed RECoverable Autonomous Sonde (RECAS) will allow analysis and sampling of subglacial water while the subglacial lake remains isolated from the surface. The probe is equipped with two electrically heated melting tips, one on the bottom and one on the top of a cylindrical probe. When one of the tips is powered, the RECAS moves up or down similarly to a hot-point thermal electric drill. The electric power and signal cable is coiled inside the probe on an electric-motor-powered coil. When the lower tip is powered, the probe advances downwards by gravity. In order to move the probe up, power is applied to the upper heated tip and the coil motor pulls the cable, moving the probe upwards and melting the borehole above the probe. A conventional internal combustion engine electric generator on the glacier surface provides 9–10 kW of power to the RECAS via an umbilical cable stored in the probe. Electric power enables a penetration rate of 2.4–2.9m h–1, and thus 4–5 months will be required to reach a depth of 3500 m and return to the surface.

On 1 December 2011 the West Antarctic Ice Sheet (WAIS) Divide ice-core project reached its final depth of 3405 m. The WAIS Divide ice core is not only the longest US ice core to date, but is also the highest-quality deep ice core, including ice from the brittle ice zone, that the US has ever recovered. The methods used at WAIS Divide to handle and log the drilled ice, the procedures used to safely retrograde the ice back to the US National Ice Core Laboratory (NICL) and the methods used to process and sample the ice at the NICL are described and discussed.

Simulations of glacier evolution are needed to assess future changes in the runoff regime of mountain catchments. A simplified parameterized model is applied here to simulate future thickness changes and glacier retreat of Mer de Glace, French Alps. A normalized thickness change function describing the spatial distribution of surface-elevation changes as a function of elevation has been determined. The model reveals that under present climatic conditions Mer de Glace will continue to shrink dramatically in the coming decades, retreating by 1200 m between now and 2040. The method has certain limitations related to the uncertainties of the normalized function based on thickness change data. An error of 10% in the normalized function leads to uncertainties of 46%, 30% and 18% in Mer de Glace front, surface area and glacier-wide mass-balance changes respectively in 2040. Because the difference of the normalized function largely exceeds 10% from one glacier to another, even within a given glacier size class and elevation range, it would be very risky to extrapolate the normalized function to unmeasured glaciers. Consequently, the method is applicable only on glaciers where past surface elevation changes are well constrained.

To study the glaciological processes controlling the mass budget of Greenland’s peripheral glaciers and ice caps, field measurements were carried out on Qaanaaq ice cap, a 20 km long ice cap in northwestern Greenland. In the summer of 2012, we measured surface melt rate, ice flow velocity and ice thickness along a survey route spanning the ice margin (200m a.s.l.) to the ice-cap summit (1110m a.s.l.). Melt rates in the ablation area were clearly influenced by dark materials covering the ice surface, where degree-day factors varied from 5.44 mm w.e. K–1 d–1 on a clean surface to 8.26 mm w.e. K–1 d–1 in the dark regions. Ice velocity showed diurnal variations, indicating the presence of surface-meltwater induced basal sliding. Mean ice thickness along the survey route was 120 m, with a maximum thickness of 165 m. Ice velocity and temperature fields were computed using a thermomechanically coupled numerical glacier model. Modelled ice temperature, obtained by imposing estimated annual mean air temperature as the surface boundary condition, was substantially lower than implied by the observed ice velocity. This result suggests that the ice dynamics and thermodynamics of the ice cap are significantly influenced by heat transfer from meltwater and changing ice geometry.

Many of the ice-coring objectives in the Ice Drilling Program Office (IDPO) Long Range Science Plan, such as those in the International Partnerships in Ice Core Sciences (IPICS) 2k array and 40k network, are attainable in many locations with an intermediate depth drill (IDD) that can collect core from a fluid-filled hole down to 1500 m depth. The Ice Drilling Design and Operations (IDDO) group has designed and is in the process of building an agile IDD to meet this objective. The drill tent, power distribution and core-processing systems are an integral part of the IDD, which can be deployed by small aircraft and assembled by hand to minimize logistic requirements. The new drill system will be ready for testing in Greenland beginning in late spring 2014. The first production drilling is scheduled for the 2014/15 field season at the South Pole.

Isolated areas of high basal drag, or ‘sticky spots’, are important and poorly understood features in the force balance and dynamics of West Antarctic ice streams. Characterizing sticky spots formed by thin or drying subglacial till using ice-penetrating radar is theoretically possible, as high radar bed-returned power (BRP) is commonly related to an abundance of free water at the ice/bed interface, provided losses from englacial attenuation can be estimated. In this study we use airborne radar data collected over Evans Ice Stream to extract BRP profiles and test the sensitivity of BRP to the adopted englacial attenuation correction. We analyse 11 ~ 2 0 km profiles in four fast-flow areas where sticky spots have been inferred to exist on the basis of model and surface data inversions. In the majority of profiles we note that the increase in basal drag is accompanied by a decrease in BRP and suggest that this is evidence both for the presence of a sticky spot in those locations and that local variations in subglacial hydrology are responsible for their existence. A comparison is made between empirical and numerical modelling approaches for deriving englacial attenuation, and our findings generally support previous studies that advocate a modelling approach.

The introduction of low-temperature fluid into boreholes drilled in ice sheets helps to remove drilling cuttings and to prevent borehole closure through visco-plastic deformation. Only special fluids, or mixtures of fluids, can satisfy the very strict criteria for deep drilling in cold ice. The effects of drilling fluid on the natural environment are analyzed from the following points of view: (1) occupational safety and health; (2) ozone depletion and global warming; (3) chemical pollution; and (4) biological pollution. Traditional low-temperature drilling fluids (kerosene-based fluids with density additives, ethanol and n-butyl acetate) cannot be qualified as intelligent choices from the safety, environmental and technological standpoints. This paper introduces a new type of low-temperature drilling fluid composed of synthetic ESTISOLTM esters, which are non-hazardous substances. ESTISOLTM 140 mixtures with ESTISOLTM 165 or ESTISOLTM F2887 have an acceptable density and viscosity at low temperature. To avoid the potential for biological contamination of the subglacial environment, the borehole drilling fluid should be treated carefully on the surface.