Within the present publication, the rotor head of a compound helicopter known as Rapid And Cost-Effective Rotorcraft (RACER) is investigated. In particular, the aerodynamic design optimisation of the RACER blade-sleeve fairings (BSFs) is conducted. For this purpose, an isolated rotor head is generated featuring a full-fairing beanie, the BSF and a truncated rotor blade (RB). Moreover, a single RB is investigated at two different azimuthal rotor positions, which correspond to the advancing and the retreating RB case. For this purpose, an averaged circumferential velocity is determined in the blade-sleeve region and superposed with the RACER cruise speed in order to estimate the prevailing flow conditions. The automated aerodynamic design optimisation is performed by means of a previously developed optimisation tool chain. A global multi-objective genetic optimisation algorithm is applied for the given problem. During preliminary work, a 2D aerodynamic design optimisation of selected blade-sleeve sections was conducted. These optimised aerofoils represent the design variables for the current optimisation problem. The shape modification of the 3D fairing is realised by exchanging specific aerofoils at certain spanwise sections.

This study focuses on the co-operative salvo attack problem of multiple missiles against a stationary target under jointly connected switching topologies subject to time-varying communication delays. By carefully exploring certain features of the typical pure proportional navigation guidance law, a two-stage distributed guidance scheme is proposed without any information on time-to-go in this study to realise the simultaneous attack of multiple missiles. In the first guidance stage, a co-operative guidance law is proposed using local neighbouring communications only to achieve consensus on range-to-go and heading error to provide favourable initial conditions for the latter phase, in which switching topologies and time-varying communication delays are taken into account when obtaining sufficient conditions of consensus in terms of linear matrix inequalities. Then, missiles disconnect from each other and are guided individually by the typical pure proportional navigation guidance law with the same navigation gain to realise salvo attack in the second guidance phase. Finally, numerical simulations are carried out to clearly validate the theoretical results.

Low Reynolds number blade profiles of ReC=105–2×105 as based on the chord length and used for small unnamed air vehicles, and near space applications are investigated for single and counter-rotating (co-axial) proprotors, i.e. acting as rotors or propellers. Such profiles are prone for early stall, significantly reducing their maximum lift to drag ratio. Two profiles previously designed by our continuous surface curvature design approach named as CIRCLE are investigated in order to improve the performance of the proprotors. The profiles are redesigns of the common symmetric NACA0012 and asymmetric E387 profiles. Using general arguments based on composite efficiency and rotor’s lift to drag ratio, the performance envelope is noticeably increased when using the redesigned profiles for high angles of attack due to stall delay.

A new approach is derived to account for the distance between the rotors of a co-axial proprotor. It is coupled with a blade element method and is verified against experimental results. Single and co-axial CIRCLE-based proprotors are investigated against the corresponding non-CIRCLE-based proprotors at hover and axial translation. Noticeable improvements are observed in thrust increase and power reduction at high angles of attack of the blade’s profiles, particularly for the co-axial configuration. Plots of thrust, torque, power, composite efficiency and aerodynamic efficiency distributions are given and analysed.

A new aerofoil parameterisation method is put forward to represent an aerofoil by combining the leading edge modification class/shape function transformation (LEM CST) method and improved Hicks–Henne bump function’s method. The new class/shape function transformation (NEW CST) method has two additional basis functions comparing the original CST method. In order to confirm these two basis functions, the radial basis functions neural network (RBF) model is trained by some samples which are generated by the Latin hypercube design (LHD) method and Genetic Algorithm (GA) is proposed to achieve the basis functions of the NEW CST method. The NEW CST method has been evaluated in fitting precision of 1,545 aerofoils by comparison with the LEM CST method and the original CST method. And the improved ability of the NEW CST at the leading edge and trailing edge is verified by a series of complex aerofoil case studies within 1,545 aerofoils. The results indicate that the NEW CST method can represent the whole aerofoils and possesses the intuitive property as well as the original CST. Moreover, the number of control parameters (NCP) to parameterise aerofoils is the fewest among these three methods. Furthermore, when the NCP of the NEW CST and LEM CST is the same, the NEW CST method has the higher accuracy and smaller root mean square errors (RMSE) especially at the leading edge and trailing edge.

This work revisits analyses of lifting line theory by A.R. Collar from 1958, bringing to bear some modern tools and techniques. The 2D vortex lattice model is also considered. Interesting combinatorial properties and simplified expressions for terms are presented, a simplified proof of model convergence shown, extension of the convergence properties to elliptical and arbitrary wing planforms is demonstrated, and approximations provided. An alternative proof of the optimality of constant downwash is presented. Modern automated theorem proving techniques are employed in confirming the combinatorial results.

Launching orbital and suborbital rockets from a high altitude is beneficial because of e.g. nozzle optimisation and reduced drag. Aircraft and gas balloons have been used for the purpose. Here we present a concept where a balloon is filled with pure water vapour on ground so that it rises to the launch altitude. The system resembles a gas balloon because no onboard energy source is carried, and no hard objects fall down. We simulate the ascent behaviour of the balloon. In the baseline simulation, we consider a 10 tonne rocket lifted to an altitude of 18 km.We model the trajectory of the balloon by taking into account steam adiabatic cooling, surface cooling, water condensation and balloon aerodynamic drag. The required steam mass proves to be only 1.4 times the mass of the rocket stage, and the ascent time is around 10 minutes. For small payloads, surface cooling increases the relative amount of steam needed, unless insulation is applied to the balloon skin. The ground-filled steam balloon seems to be an attractive and sustainable method of lifting payloads such as rockets into high altitude.

In order to ensure low-altitude safety, a tracking and recognition method of unmanned aerial vehicle (UAV) and bird targets based on traditional surveillance radar data is proposed. First, several motion models for UAV and flying bird targets are established. Second, the target trajectories are filtered and smoothed with multiple motion models. Third, by calculating the time-domain variance of the model occurrence probability, the model conversion probability of the target is estimated, and then the target type is identified and classified. The effectiveness and robustness of the algorithm is demonstrated by several groups of Monte Carlo simulation experiments, including setting different recognition steps, different model transformation probability, filtering and smoothing algorithm comparison. The algorithm is also successfully applied on the ground-truth radar data collected by the low-altitude surveillance radar at airport and coastal environments, where the targets of UAVs and flying birds could be tracked and recognised.

In this study, an improved fluid–structure interaction (FSI) analysis method is developed for a flapping wing. A co-rotational (CR) shell element is developed for its structural analysis. Further, a relevant non-linear dynamic formulation is developed based on the CR framework. Three-dimensional preconditioned Navier–Stokes equations are employed for its fluid analysis. An implicit coupling scheme is employed to combine the structural and fluid analyses. An explicit investigation of a 3D plunging wing is conducted using this FSI analysis method. A further investigation of this plunging wing is performed in relation to its operating condition. In addition, the relation between the wing’s aerodynamic performance and plunging motion is investigated.

Infrared signal measurements from a micro-turbojet engine are conducted to understand the characteristics of the engine performance and the infrared signal by varying the exhaust nozzle configuration. A cone type nozzle and five rectangle type nozzles whose aspect ratios vary from one to five are used for this experimental work. As a result, it is confirmed that the thrust and the fuel consumption rate of the engine do not change greatly by varying the exhaust nozzle shape. In the case of the aspect ratio of 5, the specific fuel consumption of the engine is increased by about 3% compared to the reference cone nozzle, but the infrared signal can be reduced by up to 14%. As a result of measuring the temperature distribution of the plume gas, the correlation of infrared signal with plume gas temperature distribution can be understood. In the case of a cone shape, the distribution of plume gas formed to circular shape, and the high-temperature core region of plume gas continued to develop farther to the downstream. However, the temperature distribution was maintained in the rectangular shape as the aspect ratio increased, and the average temperature decreased sharply. As the aspect ratio increases, the plume spreads more widely.

Predicting mental workload of pilots can provide cockpit designers with useful information to reduce the possibility of pilot error and cost of training, improve the safety and performance of systems, and increase operator satisfaction. We present a theoretical model of mental workload, using information theory, based on review investigations of how effectively task complexity, visual performance, and pilot experience predict mental workload. The validity of the model was confirmed based on data collected from pilot taxiing experiments. Experiments were performed on taxiing tasks in four different scenarios. Results showed that predicted values from the proposed mental workload model were highly correlated to actual mental workload ratings from the experiments. The findings indicate that the proposed mental workload model appears to be effective in the prediction of pilots’ mental workload over time.

Steps required for proper acquisition and processing of laser Doppler velocimetry data for turbomachinery research applications are addressed. Turbomachinery applications are difficult due to the small internal passages, high-frequency fluctuations, large turbulence intensities, and strong secondary flows resulting in low overall signal-to-noise ratios and narrowband noise sources that cannot be removed by simple band-pass filters. Special aspects that must be considered for successful and accurate laser Doppler velocimetry studies to be conducted in turbomachinery are discussed. Specifically, the design of the measurement volume size, reflection mitigation, engineering of seed particle size and injection schema, and alignment of the traverse mechanism are addressed in terms of their importance (from literature sources) and the solutions implemented by the authors. These techniques have been applied to successfully obtain three-component, unsteady velocity data in a high-speed centrifugal compressor for aeroengine application. Processing techniques are also presented including a novel mixture-model-based statistical method for narrowband noise isolation developed by the authors. The method, validation steps, and example results are presented, showing the successful rejection of noise with high accuracy, a low failure rate, and a significant reduction in required manual inspection. This newly developed method elucidated flow features that were not clear prior to the noise removal.

Flow over a moderately swept wing is characterised by complex localised flow vortex topologies such as ‘closed’ separation bubbles or ‘open’ separation structures. A model of a complex cambered, twisted, tapered wing with 40° leading edge sweep, representative of those designed for manoeuvre at high subsonic Mach numbers, was investigated using the oil-film visualisation, stereo particle image velocimetry and force moment measurements. Wind-tunnel tests were conducted at a range of Reynolds number from 2.1×105 to 8.4×105 and at angles of incidence from −1° to 22°. Still images combined with video clips enable flow patterns over the wing model to be interpreted more clearly and accurately. Using successive images extracted from the video of flow visualisation, the movement of the oil pigment has been estimated. The influence of the Reynolds number and incidence angle was discussed through analysing the flow pattern over the wing surface. Additionally, the link between the flow structures present and the wing aerodynamic performance was studied.

With the aims of overcoming the limitations of the existing basic flow model derived from an axisymmetric generating body and extending the aerodynamic design method of the airframe/inlet integrated waverider vehicle, this study develops an upgraded basic flow model derived from an axisymmetric shock wave. It then upgrades the design method for airframe/inlet integration of an air-breathing hypersonic waverider vehicle, which is termed the ‘full-waverider vehicle’ in this study. In this paper, first, the design principle and method for the upgraded full-waverider vehicle derived from an axisymmetric basic shock wave are described in detail. Second, an upgraded basic flow model that accounts for both internal and external flows is derived from an axisymmetric basic shock wave by use of both the streamline tracing method and the method of characteristics (MOC). Third, the upgraded full-waverider vehicle is developed from the upgraded basic flow model by the streamline tracing method. Fourth, the design theories and methodologies of both the upgraded basic flow model and the upgraded full-waverider vehicle are validated by a numerical computation method. Finally, the aerodynamic performances and viscous effects of both the upgraded basic flow model and the upgraded full-waverider vehicle are analysed by numerical computation. The obtained results show that the upgraded basic flow model and aerodynamic design method are effective for the design of the airframe/inlet integration of an air-breathing hypersonic waverider vehicle.

In this paper, longitudinal and lateral-directional aerodynamic characterisation of the Cropped Delta Reflex Wing (CDRW) configuration–based unmanned aerial vehicle is carried out by means of full-scale static wind-tunnel tests followed by full-scale flight testing. A predecided set of longitudinal and lateral/directional manoeuvres is performed to acquire the respective flight data, using a dedicated onboard flight data acquisition system. The compatibility of the acquired dynamics is quantified, in terms of scale factors and biases of the measured variables, using Kinematic consistency check. Maximum likelihood (ML), least squares and newly emerging neural Gauss–Newton (NGN) methods were implemented for a wing-alone delta configuration, mainly to capture the dynamic derivatives for both longitudinal and lateral directional cases. Estimated damping and weak dynamic derivatives, which are in general challenging to capture for a wing alone configuration, are consistent using ML and NGN methods. Validation of the estimated parameters with aerodynamic model is performed by proof-of-match exercise and are presented therein.

The wake vortex of lifting surfaces such as wind turbine blades or fixed-wing aircraft can heavily affect the blade aerodynamics of rotorcraft. Using blade element theory, the pilot control inputs required to mitigate such vortex effects are estimated and compared to the available control margin at the operating condition of interest. In contrast, when no pilot action is performed, the rotor blade flapping caused by the vortex is evaluated and compared to available margins. It is a safety concern when the remaining margins become zero. The influence of the vortex strength, its core radius and orientation to the rotor disk are evaluated and the effect of rotor blade characteristics (Lock number, natural frequency) is investigated.

Aircraft handling qualities may be influenced by wing-tip flow separations and horizontal tail (HT) reduced efficiency caused by loss of local dynamic pressure or local tailplane flow separations in high angle-of-attack manoeuvres. From the flight tester’s perspective, provided that the test aircraft presents sufficient longitudinal control authority to overcome an uncommanded nose-up motion, this characteristic should not be a safety factor. Monitoring and measuring the local airflow in the aircraft’s HT provides information for safe flight-test envelope expansion and data for early aerodynamic knowledge and model validation. This work presents the development, installation and pre-flight calibration using computational fluid dynamics (CFD), flight-test calibration, results and benefits of differential pressure based local angle-of-attack and total pressure measurements through 20 static pressure ports and a Kiel pitot. These sensors were installed in a single-aisle, four-abreast, full fly-by-wire medium-range jet airliner with twin turbofan engines and conventional HT (low vertical position).

A flow corridor is a new class of trajectory-based airspace that encloses groups of flights which fly along the same path in one direction and accept responsibility for separation from each other. A well-designed corridor could reduce the airspace complexity, decrease the workload of air traffic controllers and increase the airspace capacity. This paper analyses the impact of different self-separation parameters on capacity and conflicts of the flow corridor. Both the quantitative impact and interaction effects of pairs of parameters are evaluated using the combined discrete-continuous model and Monte Carlo simulation method. The simulation results show that although the initial separation is the dominating factor, the interactions between initial separation and separation buffer, minimum separation, extra switch buffer, extra threshold buffer and velocity difference threshold also have some significant impacts on the capacity and conflicts for the flow corridor.

There is a growing interest in the use of alternative fuels in gas turbine engines to reduce emissions. Testing of alternative fuels is expensive when done on a large-scale gas turbine engine. In this study, a re-commissioned small gas turbine auxiliary power unit (APU) has been used to test various blends of Jet A-1, synthetic paraffinic kerosene (SPK) and diesel with as well as eight other novel fuels. A detailed analysis of performance, gaseous emissions and particulate emissions has been presented in this study. It is observed that aromatic content in general as well as the particular chemical composition of the aromatic compound plays a vital role in particulate emissions generation. SPK fuel shows substantially lower particulate emissions with respect to Jet A. However, not all the species of aromatics negatively impact particulate emissions. Gaseous emissions measured are comparable for all the fuels tested in this study.

In order to increase the speed, precision and robustness against the engine failure in solving optimal endo-atmospheric ascent trajectory of a launch vehicle, a rapid multi-layer solving method with improved numerical algorithms was proposed. The proposed method is capable of decomposing a large number of intervals into multiple layers with advantageous convergence property. Firstly, the problem of solving optimal endo-atmospheric ascent trajectory, which was subjected to path constraints and terminal constraints, was transformed into a Hamilton Two Point Boundary Value Problem (TPBVP). Then, through the finite difference method and numerical solving algorithm, the Hamilton TPBVP was iteratively solved with fewer initial discrete intervals. The initial values of higher-layer iterations were obtained by interpolating convergent solutions at sparse nodes into the doubly discrete nodes of high layers. The process was repeatedly performed until the solving precision met the requirements. To decrease the calculation load in solving TPBVPs, two improved solving algorithms without and with fewer Jacobian calculations were studied, respectively the Derivative-free Spectral Algorithm for Nonlinear Equations(DF-SANE) combined with the improved derivative-free nonmonotone line search strategy, and the Modified Newton method with a relaxation factor in combination with the Inverse Broyden Quasi-Newton method, denoted as ‘MN-IBQ’. Simulation verifications showed that the multi-layer method had significantly higher solving speed than the single-layer method. For the improved numerical algorithms, the DF-SANE was trapped in the local convergence problem. While using the proposed MN-IBQ can further increase the solving rate. Typical engine failure simulations showed that the multi-layer method with the MN-IBQ algorithm had not only significantly higher solving speed but also stronger robustness, where the traditional single-layer method could not adapt. In addition, the thrust loss tolerance limits for the multi-layer solving method were given for different engine failure times. The results show promising potential of the proposed approach in trajectory online generation and closed-loop guidance of launch vehicles at the endo-atmospheric ascent stage.

Values are important in understanding the managerial behaviour. Values are the unique criteria that enable people to become conscious of social relations and duties. We contribute to this understanding through determining the values which affect an organisation’s business approach by providing evidence from a comparative study of various airports through a questionnaire method. The study was carried out with 163 participants and factor analysis was used to reduce the complexity of a data set so that it becomes easier to use the data in applied settings. Ranking analysis was used to get the values hierarchy of managers. This hierarchy-addicted culture helps to understand corporate sustainability and loyalty. Managing values increases quality and retains sustainability. Further suggestions are made regarding values that should be taken into consideration for achieving corporate strategies, whether operating regionally or globally. This study contributes towards improving awareness on the effects of values in business management in both theory and practice, along with their limitations. The analysis shows that there is a conformity between organisational and individual values.