The effects of the flow of exhaust gases intentionally orientated on the rear wing element of a generic Formula One car body have been studied. A qualitative analysis of the effectiveness of a cold nitrogen jet on a NACA 0012 type of aerofoil has been conducted. The Reynolds number of the jet was 13,000, based on the jet velocity and diameter, and of the bodywork was 54,000, based on the free stream velocity and bodywork length. The lift coefficient was measured via a three-component strain-gauge force balance at four different ground-to-aerofoil heights (32, 45, 60 and 90mm) and incidence range –20 to +20 degrees. The surface flow patterns were visualised using the oil flow technique and were compared with numerical simulations. Pressure measurements were conducted using pressure tappings. The CFD solver was FLUENT. The RNG k-ε model was selected to solve the turbulent flow transport equations. The numerical study also comprised the investigation of the aspiration generated by exhaust gases when these are ejected inside a duct of greater diameter. A parametric investigation relating the relative diameter of exhaust pipe and outer duct and the relative overlap between the sides of the duct and the exhaust pipe was performed.

Aerodynamic optimisations of a blended wing-body (BWB) aircraft are presented. A discrete adjoint solver is used to calculate efficiently the gradients, which makes it possible to optimise for a large number of design variables. The optimisations employ either a variable-fidelity method that combines low- and high-fidelity models or a direct sequential quadratic programming (SQP) method. Four Euler optimisations of a BWB aircraft are then presented. The optimisation is allowed to change a series of master sections defining the aircraft geometry as well as the sweep angle on the outer wing for two of the optimisations. Substantial improvements are obtained, not only in the Euler mode but also when the optimised geometries are evaluated using Reynolds-averaged Navier-Stokes solutions. Some interesting features of the optimised wing profiles are discussed.

Kite testing by flying in a horizontal circle, was developed in order to address the inevitable accuracy problems inherent in pre-existing kite measurement techniques. However the raw results from this circular flight method are not directly comparable with traditional kite performance measurements. To enable direct comparisons to be made, modifying equations have been developed to convert the raw circular flight results into the traditional measurements of lift to drag ratio, and lift coefficient. This paper derives the modifying equations, and presents experimental results comparing traditional measurements with both the raw and modified circular flight results. The modifying equations are applied to an example set of results to assess the sensitivity of the test environment parameters. It is concluded that for many cases, the discrepancy between the raw circular flight test results and traditional measurement techniques is small enough to ignore. Alternatively, the modifying equations given in the paper may readily be encoded so that traditional results may be quickly obtained from this novel test method.

This paper presents a dynamic analysis of a single-line kite with two degrees of freedom. A Lagrangian formulation is used to write convenient equations of motion. The equilibrium states of the system and their stability are studied; Eigenvalues and eigenmodes are calculated by using linear theory. The stability in the parametric plane δ – W0 is discussed, where δ defines the bridle geometry and W0 is wind velocity. The system goes through a Hopf bifurcation and periodic branches of solutions appear. The orbits and their stability have been calculated numerically using Floquet theory and wind velocity seems to play an important role in their existence. Finally the kite response against gusts is considered and an open loop control system developed to keep the flight altitude invariant under changing atmospheric conditions. Modifying the bridle’s geometry seems to be a convenient way to control a kite’s performance.

This paper applies existing information on solar storms to unmanned aviation; no new research data is presented. The purpose of this paper is to alert the unmanned aviation community to the potential hazards posed by solar storms, to familiarise it with the effects of solar storms and how to mitigate them, and to encourage research on solar storm effects on high altitude long endurance (HALE) aircraft and airship design and operations. As unmanned aircraft and airships move increasingly into high altitude (50,000+ft), endurance (24+ hr) roles, they will become vulnerable to the effects of space weather, specifically that of solar storms. Although solar storms are commonly associated with their impact on satellites, they affect the routing and timing of airline flights flying for six to eight hours at 30,000 to 40,000ft. Operating twice as high and with flight times twice as long (or longer) than those of airliners, HALE aircraft and airships occupy a middle zone of vulnerability, being more so than airliners but less so than satellites. A key difference however is that satellites are designed for space weather, whereas some current HALE vehicles are not. The paper concludes that unmanned HALE aircraft and airships can be one to three orders of magnitude more vulnerable to solar storms than a trans-Pacific airliner.

This work presents a method for selecting the gain parameters of a C* control law for an aircraft’s longitudinal motion. The design incorporates various handling quality requirements involving modal, time- and frequency-domain criteria that were fixed by the aircraft manufacturer. After necessary model order-reductions, the design proceeds in essentially two-steps: stability augmentation system (SAS) loop design and control augmentation system (CAS) loop design. The approach partly relies on the use of guardian maps to characterise, in each case, the set of gain parameters for which desired handling quality requirements are satisfied. The approach is applied throughout the full flight envelope of a business jet aircraft and yields satisfactory results.