Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-26T12:03:06.644Z Has data issue: false hasContentIssue false
  • English
  • Français

Numerical calculation of separated flow past square and rectangular cylinders using panel technique

Published online by Cambridge University Press:  03 February 2016

A. Roy  and
G. Bandyopadhyay
A. Roy
Affiliation:
Department of Space Engineering and Rocketry, Birla Institute of Technology, Mesra, Ranchi, India
G. Bandyopadhyay
Affiliation:
Department of Aerospace Engineering, Indian Institute of Technology, Kharagpur, India
Get access Rights & Permissions [Opens in a new window]

Abstract

In the present investigation, a potential flow model based on panel method has been developed for calculation of two dimensional separated flows past square and rectangular cylinders. Free vortex lines are assumed to emanate from the points of separation that converge downstream of the body. The converged wake shape is iteratively obtained by integrating the velocity vectors at the collocation points. For solving separated flow past square and rectangular cylinders, four different versions of the solver have been developed for a wide range of incidence, namely, for zero, low, moderate and high angles of incidence. For validation of computed results, experimental investigations have been carried out in a low speed wind tunnel to obtain the surface pressure distribution on square cylinder and rectangular cylinder over a range of angles of incidence. Comparison is reasonably good.

Type
Research Article
Information
The Aeronautical Journal , Volume 110 , Issue 1106 , April 2006 , pp. 249 - 256
Copyright
Copyright © Royal Aeronautical Society 2006 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Lee, B.E., The effect of turbulence on the surface pressure field of a square prism, J Fluid Mech, 1975, 69, (2), pp 263–282.Google Scholar
2. Robertson, J.M., Wedding, J.B., Peterka, J.S. and Cermac, J.E., Wall pressures of separation- reattachment flow on a square prism in uniform flow, J Wind Engg Ind Aerodyn, 1978, 2, pp 345–359.Google Scholar
3. Igarashi, T., Characteristics of the flow around a square prism, Bulletin of JSME, 1984, 27, (231), pp 1858–1865.Google Scholar
4. Chen, J.M. and Liu, C.H., Vortex shedding and surface pressures on a square cylinder at incidence to a uniform air stream, Int J Heat and Fluid Flow, 1999, 20, pp 592–597.Google Scholar
5. Igarashi, T., Characteristics of the flow around rectangular cylinders (the case of the angle of attack 0 deg.), Bulletin of JSME, 1985, 28, (242), pp 1690–1696.Google Scholar
6. Sam, R.G., Lessman, R.C. and Test, F.L., An experimental study of flow over a rectangular body, J Fluids Engg, 1979, 101, pp 443–448.Google Scholar
7. Bearman, P.W. and Trueman, D.M., An investigation of the flow around rectangular cylinders, Aero Q, 1972, 23, (3), pp 229–237.Google Scholar
8. Da Matha Sant Anna, F.A., Laneville, A., Trepanier, J.Y. and Lu, Z.Y., Detailed pressure field measurements for some 2-D rectangular cylinders, J Wind Engg Ind Aerodyn, 1988, 28, pp 241–250.Google Scholar
9. Laneville, A. and Yong, L.Z., Mean flow patterns around two-dimensional rectangular cylinders and their interpretation, J Wind Engg Ind Aerodyn, 1983, 14, pp. 387–398.Google Scholar
10. Obasaju, E., An investigation of the effects of incidence on the flow around a square section cylinder, Aero Q, 1983, 34, pp 243–259.Google Scholar
11. Nakaguchi, H., Hashimoto, K. and Muto, S., An experimental study on aerodynamic drag of rectangular cylinders, J Japanese Soc Aero Space Science, 1968, 16, pp 1–5.Google Scholar
12. Bostok, B.R. and Mair, W.A., Pressure distribution and forces on rectangular and D- shaped cylinders, Aero Q, 1972, 23, pp 1–6.Google Scholar
13. Sarpkaya, T., Computational Methods with Vortices – The 1998 Freeman Scholar Lecture, J Fluids Engg, 1989, 111, pp 5–52.Google Scholar
14. Inamuro, T., Adachi, T. and Sakata, H., A numerical analysis of unsteady separated flow by vortex shedding model, Bulletin of JSME, 1983, 26, (222), pp 2106–2112.Google Scholar
15. Sarpkaya, T. and Ihrig, C.J., Impulsively-started flow about rectangular prisms- experiments and discrete vortex analysis, J Fluids Engg, 1986, 108, pp 47–54.Google Scholar
16. Nagano, S., Naito, M. and Takata, H., A numerical analysis of two-dimensional flow past a rectangular prism by a discrete vortex model, Computers and Fluids, 1982, 10, (4), pp 243–259.Google Scholar
17. Stansby, P.K., A generalized discrete-vortex method for sharp-edged cylinders, AIAA J, 1985, 23, (6), pp 856–861.Google Scholar
18. Sarpkaya, T. and Schoaff, R.L., Inviscid model of two-dimensional vortex shedding by a circular cylinder, AIAA J, 1979, 17, (11), pp 1193–1200.Google Scholar
19. Basuki, J. and Graham, J.M.R., Discrete vortex computation of separated airfoil flow, AIAA J, 1987, 25, (11), pp 1409–1410.Google Scholar
20. Maskew, B. and Dvorak, F.A., The prediction of Clmax using a separated flow model, J American Heli Soc, 1978, 23, pp 2–8.Google Scholar
21. Ribaut, M., A vortex sheet method for calculating separated two-dimensional flows, AIAA J, 1983, 21, (8), pp 1079–1084.Google Scholar
22. Mukherjea, S. and Bandyopadhyay, G., Separated flow about a wedge, Aeronaut J, 1990, 94, (936), pp 196–202.Google Scholar