This work reports a comparative study of laser ion implantation mainly performed at the Nuclear Physics Institute in Rez (Czech Republic), National Institute of Nuclear Physics (Italy), and the Plasma Physics Laboratory at the University of Messina (Italy) using different approaches. Thick metallic targets were irradiated in vacuum by a focused laser beam to generate plasma-producing multi-energy and multi-species ions. A post-acceleration system was employed in order to increase the energy of the produced ions and to generate ion beams suitable to be implanted in different substrates. The ion dose was controlled by the laser repetition rate and the time of irradiation. Rutherford backscattering analysis was carried out to evaluate the integral amount of implanted ion species, the concentration–depth profiles, the ion penetration depth, and the uniformity of depth profiles for ions laser implanted into monocrystalline substrates. The laser implantation under normal conditions and in post-acceleration configuration will be discussed on the basis of the characterization of the implanted substrates.

We study the interaction of an ultra-high intensity laser pulse with plastic flat-top cone targets with curved walls and cone targets with straight walls. We find the appropriate type, dimensions of the cone target, and the ultra-high intensity laser pulse parameters for which the accelerated ions have the maximum energy and their number is the highest for a lower angular divergence and a better laser absorption. This numerical study will allow one to prepare and optimize first laser-ion acceleration experiments on CETAL using micro-cone targets.

The effect of the initial phase distortion of the laser on near-field transmission characteristics in free space is investigated both numerically and theoretically. It is demonstrated and proposed that the near-field modulation and fluence contrast of the output laser beam are changing with the increase of both spatial low- and high-frequency wavefront distortion. The simulation results show that in order to ensure the beam quality in propagation, the Fresnel number should be controlled not <50 generally and the wavefront distortion should also be minimized by controlling both low- and high-frequency phase coefficient not larger than 0.6.

This paper presents a scheme of THz generation by nonlinear photomixing of two cosh-Gaussian lasers pulses having different frequencies (ω1, ω2) and wave numbers $(\vec k_1, \vec k_2 )$ and same electrical field amplitude in a corrugated plasma embedded with transverse static magnetic field. Cosh-Gaussian laser pulses have steep gradient in intensity profile along with wider cross-section, which exerts a stronger nonlinear ponderomotive force at ω1 − ω2 and $\vec k_1 - \vec k_2 $ on plasma electrons imparting a nonlinear oscillatory velocity to plasma electrons. Oscillatory plasma electrons couple with the density ripple n′ = nα0eiαx to produce a nonlinear current, which is responsible for resonant THz radiation at frequency $\sim\left( {{\rm \omega} _{\rm c}^2 + {\rm \omega} _{\rm p}^2} \right)^{1/2} $. The amplitude, efficiency and beam quality of THz radiation can be optimized by choosing proper corrugation factor (α of the plasma), applied magnetic field (ωc), decentered parameter (b), and beam width parameter a0 of cosh-Gaussian lasers. An efficiency of $\sim\!10^{ - 2} - 10^{ - 1} $ is achieved for laser electric field E = 3.2 × 109 V/cm.

The paper presents results of two-dimensional particle-in-cell simulations of ion beam acceleration at the interactions of a 130-fs laser pulse of intensity in the range 1021–1023 W/cm2, predicted for the Extreme Light Infrastructure lasers, with thin hydrocarbon (CH) or erbium hydride (ErH3) targets. A special attention is paid to the effect of the laser pulse intensity and polarization (linear, circular) on the proton energy spectrum, the proton beam spatial distribution and the proton pulse shape and intensity. It is shown that for the low laser intensities (~1021 W/cm2) considerably higher proton beam parameters (proton energies, beam intensities) are achieved for the ErH3 target for both polarizations and the effect of polarization on the beam parameters is significant (higher parameters are achieved for the linear polarization). However, for the highest, ultra-relativistic intensities (~1023 W/cm2) higher proton beam parameters are attained for the CH target and the effect of polarization on these parameters is relatively low. In this case, for both polarizations quasi-monoenergetic proton beams are generated from the CH target of the mean proton energy ~2 GeV and $dE_{\rm p} /\bar E_{\rm p} \approx 0.3$ for the linear polarization and $dE_{\rm p} /\bar E_{\rm p} \approx 0.2$ for the circular one. At the highest laser intensities also the proton pulse peak intensities are higher for the CH target and for both polarizations they reach values well above 1021 W/cm2. In the paper, the properties of proton beam generation indicated above are discussed in detail and a physical explanation of the observed effects is done.

The role played by the angle of incidence of a short pulse laser in the generation of magnetic field via Weibel instability from overdense plasmas is investigated with the help of three-dimensional particle-in-cell simulations. The simulations have been done for different cases by varying the angle of incidence. When the laser pulse is incident normally (θ = 0°), it gets self-focused at a very short distance and the axial intensity rises up to several times the fundamental laser intensity. Strong current filamentation is observed, which causes the generation of high magnetic fields across the current filament. When the laser is incident obliquely at θ = 30° and 60°, periodic density ripple-like structures are formed on the plasma surface which is due to emission of energetic electron jets caused by vacuum heating. The periodic structures carry forward and return currents, which results in the formation of periodic magnetic field structures having strong magnetic fields. At θ = 60°, the inter spacing distance coincides with the incident laser wavelength. The magnetic energy is found to be highest in case of normal incidence, which is due to strong current filamentation. The filamentation becomes weaker as the angle of incidence is increased.

Stimulated Brillouin backscattering of an intense hollow Gaussian laser beam (HGLB) from collisionless plasma has been investigated under relativistic–ponderomotive regime. The main feature of considered hollow Gaussian laser beam is having the same power at different beam orders with null intensity at the center. Backscattered radiation is generated due to nonlinear interaction between main beam (pump beam) with pre-excited ion acoustic wave (IAW). Modified coupled equations has been set up for the beam width parameters of the main beam, ion-acoustic wave, back-scattered wave, and back reflectivity of stimulated Brillouin scattering (SBS) with the help of the Wentzel–Kramers–Brillouin approximation, fluid equations and paraxial theory approach. These coupled equations are solved analytically and numerically to study the laser intensity in the plasma, the variation of amplitude of the excited IAW and back reflectivity of SBS. The back reflectivity of SBS is found to be highly sensitive to the order of the HGLB, intensity of main laser beam, and plasma density for typical laser and plasma parameters. The focusing of main laser beam (hollow Gaussian) and IAW significantly affected the back reflectivity of SBS. The results show that the self-focusing and back reflectivity is enhanced for higher order modes of HGLB.

The temporal correlation between neutron and hard X-ray (HXR) emissions from a hundred joules plasma focus device (PF-400J) was studied. A method, time history analysis, to estimate the time of origin of neutrons with respect to HXRs is applied. In most of the discharges, it was found that neutrons are originated before HXRs in the axial direction and after HXRs in the radial direction. In some discharges, the time difference between HXRs and neutrons origin was found large enough, so that it can be interpreted that those neutrons would have been originated before the pinch. A qualitative discussion is conjectured to explain the experimental observations.

The origin and characteristics of near-microcoulomb multi-MeV electrons accelerated by short pulse lasers interacting with near-critical density plasma in self-formed channels are studied using three-dimensional particle-in-cell simulations. According to the analysis on interaction phenomena and electron dynamics, the dominant mechanism turns out to be direct laser acceleration, which ensures the outstanding energy coupling. Additionally, self-channeling is found to be a decisive factor for the acceleration performance, as electrons obtain ultra-high energy through betatron resonance inside the channels. In our findings, by using a relativistic short laser pulse and near-critical plasma, a large amount of energetic electrons can be generated, presenting a promising and accessible route to ultraintense, high-spatial-resolution radiation pulses.

Graphene micrometric particles have been embedded into polyethylene at different concentrations by using chemical–physical processes. The synthesized material was characterized in terms of mechanical and optical properties, and Raman spectroscopy. Obtained targets were irradiated by using a Nd:YAG laser at intensities of the order of 1010 W/cm2 to generate non-equilibrium plasma expanding in vacuum. The laser–matter interaction produces charge separation effects with consequent acceleration of protons and carbon ions. Plasma was characterized using time-of-flight measurements of the accelerated ions. Applications of the produced targets in order to generate carbon and proton ion beams from laser-generated plasma are presented and discussed.

The use of laboratory experiments as plasma creating sources is a valuable tool for understanding astrophysical observations. Recently plasma created through irradiation by lasers with relativistic intensities has been used to study effects of hot electrons and X-ray pumping on X-ray formation of multiply charged ions spectra. This paper discusses the formation of K-shell Fe spectra recorded from a plasma irradiated by 35 fs pulses with intensities of 1021 W/cm2. Modeling of the spectra suggests three different regions of plasma radiation including a cold ~10 eV region, a mild ~700 eV region, and a hot ~3500 eV region. The influence of hot electrons and X-ray pumping is discussed and a comparison with K-shell Fe spectra from a 1 MA X-pinch experiment is included to highlight the differences due to the shorter time frame of the laser–plasma interaction experiment.

Suprathermal electrons produced by laser–plasma interactions at 0.53-μm laser wavelength have been investigated using 19 electron spectrometers. The targets were 2- and 10-μm-thick Al foils, while the laser average intensities were 2 × 1013 and 7 × 1014 W/cm2. A double temperature distribution was observed in the electron energy spectrum: the lower electron temperature was below 25 keV, whereas the higher was ~50 keV. The angular distribution of the total suprathermal electron energy approximately obeyed the Gaussian distribution, peaking along the k vector of the incident laser beam for perpendicular incidence. Furthermore, the conversion rate of laser energy into escaped suprathermal electron energy over the π sr solid angle was ~10−4 at $\sim \!\!10^{14} \; {\rm W}/{\rm c}{\rm m}^{\rm 2}$, increasing almost linearly with the laser intensity.

This paper considers the heating of a target in a shock wave created in a planar geometry by the ponderomotive force induced by a short laser pulse with intensity higher than 1018 W/cm2. The shock parameters were calculated using the relativistic Rankine–Hugoniot equations coupled to a laser piston model. The temperatures of the electrons and the ions were calculated as a function of time by using the energy conservation separately for ions and electrons. These equations are supplemented by the ideal gas equations of state (with one or three degrees of freedom) separately for ions and electrons. The efficiency of the transition of the work done by the laser piston into internal thermal energy is calculated in the context of the Hugoniot equations by taking into account the binary collisions during the shock wave formation from the target initial condition to the compressed domain. It is shown that for each laser intensity there is threshold pulse duration for the formation of a shock wave. The explicit calculations are done for an aluminum target.

In our previous research (Zhao et al., 2016), we focus on the transport processes from hot electrons to K α X-ray emission in a copper foil and nanobrush target when the electron refluxing effect is not taken into account. In this work, considering the refluxing effect, the transport of hot electrons in a solid target is studied by adding the electric fields both at the front and rear surfaces of the target with Monte Carlo code Geant4. Simulation results show that the electron refluxing has an important influence on K α photon yield and the size of K α radiation source. K α yield from the 10-μm-thick target with the electron refluxing effect is 2.7–3.7 times more than that without the refluxing for the electron temperatures from 0.4 to 1.4 MeV. The laser-to-K α photon energy conversion efficiency ${\rm \eta} _{L \to K_{\rm \alpha}} $ with the refluxing effect is always higher than that without the refluxing, and both of them decrease gradually with laser strength Iλ2. Considering the electron refluxing effect or not, the variations of K α yield with the target thickness d are very different. A critical thickness of the target d c (~30 μm) is achieved to confirm whether the refluxing effect is valid for the target. For the target with the thickness d less than d c, the refluxing effect can enhance K α yield with several times, while for the target with the thickness d larger than d c, the refluxing effect is not so effective. The full-width at half-maximum increases from 23 to 56 µm after including the refluxing effect by the electron beam with the radius of 10 µm and the temperature of 400 keV.

In the present research work, the authors have investigated the self-focusing and defocusing of Hermite-cosh-Gaussian laser (HChG) beam in an inhomogeneous rippled density plasmas. By taking the relativistic non-linearity into account, an equation for envelope is set up and solved using Wentzel–Kramers–Brillouin and the paraxial ray approximation. An ordinary non-linear differential equation governing the beam width parameter as a function of propagation distance is set up for different mode structures of the beam. Further, a numerical study of this differential equation is carried for suitable set of plasma and laser parameters. The beam undergoes periodic self-focusing/defocusing due to relativistic non-linearity. We also report the comparison between self-focusing/defocusing of HChG beam in the absence and presence of density ripple. Presence of ripple does not only leads to substantial increase in self-focusing length, but also results in oscillatory character with decreasing f. In a relativistic case, strong oscillatory self-focusing and defocusing is observed. Further, self-focusing is enhanced with increased value of decentered parameter.

In this paper, self-focusing of asymmetric cosh-Gaussian laser beams in collisionless magnetized plasma has been studied. The non-linearity in dielectric constant considered herein is mainly due to the ponderomotive force. The non-linear coupled differential equations for the beam width parameters in transverse dimensions of the beam have been obtained by using WKB and paraxial approximations under parabolic equation approach. The numerical computation is completed by using fourth-order Runge–Kutta method. The effect of unlike decentered parameters in both transverse dimensions of the beam on self-focusing of cosh-Gaussian beams has been presented. Further, the effect of the static magnetic field and polarization modes of the laser has been explored.

Measurements are reported of the target neutralization current, the target charge, and the tangential component of the magnetic field generated as a result of laser–target interaction by pulses with the energy in the range of 45–92 mJ on target and the pulse duration from 39 to 1000 fs. The experiment was performed at the Eclipse facility in CELIA, Bordeaux. The aim of the experiment was to extend investigations performed for the thick (mm scale) targets to the case of thin (μm thickness) targets in a way that would allow for a straightforward comparison of the results. We found that thin foil targets tend to generate 20–50% higher neutralization current and the target charge than the thick targets. The measurement of the tangential component of the magnetic field had shown that the initial spike is dominated by the 1 ns pulse consistent with the 1 ns pulse of the neutralization current, but there are some differences between targets of different types on sub-ns scale, which is an effect going beyond a simple picture of the target acting as an antenna. The sub-ns structure appears to be reproducible to surprising degree. We found that there is in general a linear correlation between the maximum value of the magnetic field and the maximum neutralization current, which supports the target-antenna picture, except for pulses 100s of fs long.

The effect of nature and pressure of ambient environment on laser-induced breakdown spectroscopy (LIBS) and ablation mechanisms of silicon (Si) have been investigated. A Q-switched Nd-YAG laser with the wavelength of 1064 nm, pulse duration of 10 ns, and pulsed energy of 50 mJ was employed. Si targets were exposed under ambient environments of inert gases of argon, neon, and helium for different pressures ranging from 5 to 760 torr. The influence of nature and pressure of ambient gases on the emission intensity of Si plasma have been explored by using the LIBS spectrometer system. The plasma parameters such as electron temperature and number density were determined by applying Boltzmann plot and Stark broadening method, respectively. Our experimental results suggest that the nature and pressure of ambient environment play a significant role for generation, recombination, and expansion of plasma and consequently affect the excitation temperature as well as electron density of plasma. The surface morphological analysis of laser-irradiated Si was performed by using scanning electron microscope (SEM). Various kinds of structures, for example laser-induced periodic surface structures or ripples, cones, droplets, and craters have been generated and their density and size are found to be strongly dependent upon the ambient environment. A quantitative analysis of particulate size and crater depth measured from SEM images showed a strong correlation between plasma parameters and the growth of micro/nanostructures on the modified Si surface.

Spatial confinement effects on plasma parameters and surface morphology of laser-ablated Mg are studied by introducing a metallic blocker as well as argon (Ar) gas at different pressures. Nd: YAG laser at various fluences ranging from 7 to 28 J/cm2 was employed to generate Mg plasma. Confinement effects offered by metallic blocker are investigated by placing the blocker at different distances of 6, 8, and 10 mm from the target surface; whereas spatial confinement offered by environmental gas is explored under four different pressures of 5, 10, 20, and 50 Torr. Laser-induced breakdown spectroscopy analysis revealed that both plasma parameters, that is, excitation temperature and electron number density initially are strongly dependent upon both pressures of environmental gases and distances of blockers. The maximum electron temperature of Mg plasma is achieved at Ar gas pressure of 20 Torr, whereas maximum electron number density is achieved at 50 Torr. It is also observed that spatial confinement offered by metallic blocker is responsible for the significant enhancement of both electron temperature and electron number density of Mg plasma. Maximum values of electron temperature and electron number density without blocker are 8335 K and 2.4 × 1016 cm−3, respectively, whereas these values are enhanced to 12,200 K and 4 × 1016 cm−3 in the presence of blocker. Physical mechanisms responsible for the enhancement of Mg plasma parameters are plasma compression, confinement and pronounced collisional excitations due to reflection of shock waves. Scanning electron microscope analysis was performed to explore the surface morphology of laser-ablated Mg. It reveals the formation of ripples and channels that become more distinct in the presence of blocker due to plasma confinement. The optimum combination of blocker distance, fluence and Ar pressure can identify the suitable conditions for defining the role of plasma parameters for surface structuring.

As a kind of flash heat source, intense pulsed ion beam (IPIB) can be used for material surface modification. The ablation effect has important influence on interaction between IPIB and material. Therefore, the understanding of ablation mechanism is of great significance to IPIB application. In this work, pure zinc targets were irradiated and ablated by IPIB. In the ablation process under the different ion beam energy densities, the ablation products were collected by a monocrystalline silicon substrate. By analyzing the ablation products with scanning electron microscope and energy-dispersive spectrometer, the surface morphology, and the spatial distribution of ablation products quantity were obtained. The results are useful for clearing the ablation process and the influence of beam parameter on the ablation effect.