In this paper, we address the architecture of multistandard simultaneous reception receivers and we aim to reduce the complexity and the power consumption of the analog front-end. To this end, we propose an architecture using the double orthogonal translation technique in order to multiplex two signals received on different frequency bands. A study case concerning the simultaneous reception of 802.11 g and Universal Mobile Telecommunications System (UMTS) signals is developed in this article. Theoretical and simulation results show that this type of multiplexing does not significantly influence the evolution of the signal-to-noise ratio of the signals. In the same time a 30% reduction of the power consumption is expected as well as a significant reduction of the complexity.

Many scientists and engineers contributed – more or less successfully – to the development of radio and wireless. This historical survey describes briefly the projects realized more than a century ago by some of them, at the early beginnings of wireless. It is hoped, in this manner, to draw attention to the unknown or forgotten researchers who built up the considerable body of knowledge that led to Marconi's remarkable achievements.

This paper reports a new compact dual-band axially corrugated profiled horn feed (DBCPH) for prime-focus reflector antenna at C-band (uplink and downlink frequency bands with bandwidth ratio of 1.6). DBPCH consists of one sinusoid profiled section and two internal axial corrugations (internal short-circuited ring slots), for obtaining a multimode horn feed. Such a blended structure is optimized over the specified frequency bands (3.68–3.70 and 5.865–5.915 GHz) to achieve various performance objectives (such as compactness, return loss, polarization purity, etc.). Measured and predicted results show that DBCPH provides better return loss >18.6 dB, low cross-polarization (better than −32 dB), and adequate edge taper at ±48° (8.5–11.7 dB) along with compact size (1.3λ aperture diameter and 0.88λ length at lower frequency). The horn would be used as a feed element for front-fed prime-focus reflector for pencil beam spacecraft antenna application.

In radar receivers, the low noise amplifier (LNA) must provide very low noise figure and high gain to successfully receive very low signals reflected off of illuminated targets. Obtaining low noise figure and high gain, unfortunately, is a well-known trade-off that has been carefully negotiated by design engineers for years. This paper presents a fundamental solution method for the source reflection coefficient providing the maximum available gain under a given noise figure constraint, and also for the lowest possible noise figure under a gain constraint. The design approach is based solely on the small-signal S-parameters and noise parameters of the device; no additional measurements or information are required. This method is demonstrated through examples. The results are expected to find application in design of LNAs and in real-time reconfigurable amplifiers for microwave communication and radar receivers.

In this paper, the design and analysis of a complementary Sierpinski Knopp fractal antenna are presented. It is realized by applying the Sierpinski Knopp space-filling curve on the basic square monopole antenna. The performance metrics of the antenna such as S11 (reflection coefficient), voltage standing wave ratio, radiation pattern, gain and current distribution at resonant frequencies are analyzed by using ANSYS Electronic Desktop software package. FR4 dielectric material is used as a substrate in which the radiating element of an antenna is printed. Vector network analyzer and anechoic chamber are used for measuring the fabricated antenna in order to validate the simulated data. The proposed antenna resonates at three frequencies that are 2.08, 4.93, and 6.46 GHz with a reflection coefficient of −20.5, −23.1, and −24.3 dB, respectively. The suggested antenna covers the frequency bands for mobile satellite service, Public Protection and Disaster Relief communication devoted to the emergency management system and INSAT C band applications.

A probe feed wideband multi-element dual segments quarter cylindrical dielectric resonator antenna (q-CDRA) in composite forms have been proposed. The q-CDRA has been introduced by splitting CDRA into four uniform quarters and multi-segmentation approach has been castoff for further improvement in bandwidth of q-CDRA. The dual segments q-CDRA has been designed and analyzed using theoretical analysis and Ansoft HFSS simulation software. Further the dual segment multi-element q-CDRAs in composite form have been designed. A coaxial probe has been placed at the center of the ground plane for the excitation of proposed multi-element and multi-segmented composite form of q-CDRA, which excite TM01δ mode in the proposed antenna. The input characteristics and radiation patterns of the proposed composite antennas have been studied and their results are compared with corresponding experimental results. Prototype of single, two, and four elements dual-segment composite q-CDRAs have been fabricated and input characteristics of the proposed composite antennas have been compared with each other. Four elements dual-segment composite q-CDRA has shown wide impedance bandwidth (|S11| ≤ −10 dB) of 85.13% with monopole-like radiation pattern. The peak gain of 4.85 dBi with 98.5% radiation efficiency has been achieved for dual-segment four elements composite q-CDRA. The proposed multi-element dual-segment composite q-CDRAs may find suitable applications in C and X-band with complete covering of the 5.0 GHZ wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) band.

This paper proposes an efficient and fast analysis of substrate integrated waveguide (SIW) components using a new approach of the iterative method called WCIP, i.e. “Wave Concept Iterative Process”. This method is based on the iterative resolution of waves between two domains. The first is the spectral domain. We use the Floquet–Bloch decomposition to describe all modes in the spectral domain. The second describes the configuration of the circuit in the spatial domain. It allows taking the exact structure according to the appropriate boundary conditions. This method permits to reduce numerical complexity. The convergence of this approach is always guaranteed. The theoretical suggested study is validated by the simulation of two different examples of SIW circuits. The obtained results are in good agreement with those of measurement and with software HFSS simulations, which prove the advantage of this method.

In this paper, a compact stepped slot antenna for ultra-wideband (UWB) applications is proposed. A very small size and UWB bandwidth operation are achieved by integrating a stepped slot in the back side of the antenna. This stepped slot is excited by using a 50 Ω-feed line in the top side of the antenna. The antenna is characterized by an impedance bandwidth between 3.05 GHz and more than 12 GHz. The dimensions of the antenna are 17 mm × 8 mm × 1.27 mm, which leads to the most compact size compared with other works in the literature. The integrated stepped slot is divided into additional elementary slots, where each elementary slot has a matching point. Adding these elementary slots allows to increase further the operating bandwidth. The radiation pattern of the compact stepped slot antenna is omnidirectional in the H-plane and bidirectional in the E-plane. The measurement results agree well with the simulated ones in terms of impedance matching and radiation pattern.

This study illustrates the dynamical reconfiguration of a concentric hexagonal antenna array radiation to generate a pencil beam and flat-top beam simultaneously by electronic control in two principle vertical planes under consideration. Both the beams share a common normalized optimal current excitation amplitude distribution while the optimal sets of phase excitation coefficients are varied radically across the hexagons to generate a flat-top beam. The proposed approach is able to solve the underlying multi-objective problem and flexible enough to the efficient implementation of additional design constraints in the considered φ-planes. In this paper, a set of simulation-based examples are presented in an integrated way. The outcomes validate the effectiveness of the stated optimization using meta-heuristic optimization algorithms (teaching–learning-based optimization, symbiotic organism search, multi-verse optimization) to reach the solution globally and prove actual relevance to the concerned applications.

This paper clarifies what we benefit from single-input–multiple-output (SIMO) or multiple-input–multiple-output (MIMO) radar. We have developed an X-band sparse array imaging radar system capable of operating at both SIMO and MIMO modes. The hybrid radar modes are realized without any modification in hardware, but simply by switching the scheme of waveform generation and post-processing. A comparison has been made between the SIMO mode adopting a chirp pulse waveform and the MIMO mode based on the code-division multiple access method using the Gold-coded pulse waveform. Mutually complementary properties between the SIMO and MIMO modes in terms of the cost of computation, the ease of array calibration, and the detectability of targets are clarified through simulations and an experiment.

This paper proposes, a high gain, Fabry Perot cavity antenna with coplanar waveguide (CPW) fed ultra wide band (UWB) radiating element. The proposed antenna has flat edge arrow shape-based radiating element, which act as a main radiating element and responsible for UWB radiation. This UWB microstrip antenna is parasitically coupled with an array of square parasitic patches (PPs), which act as partially reflective surface. The square patches are fabricated at the bottom of inexpensive FR4 substrate and suspended in the air with the help of dielectric rods at 1.5λ0 height. High gain is obtained by resonating PPs at near close frequencies of 3.8–8.8 GHz UWB, where partially reflective surface gives almost positive reflection phase gradients. Two laboratory prototypes of antenna, one with and another without partially reflective surface are fabricated and tested. Details of the proposed antenna design and role of partially reflective surface in gain enhancement of planar CPW fed UWB antenna are described, and typical experimental results are presented and discussed.

In this article, a dynamically switchable ultra-wideband (UWB) planar monopole antenna employing defected ground structure (DGS) with a folded stepped impedance resonator (SIR) that can operate as either a UWB mode or the single band-notched mode is introduced. The UWB monopole antenna contains a novel whirligig-shaped radiating patch and a chambered conductor as a partial ground plane. The switchable UWB antenna uses one PIN diode as switching elements in the DGS-SIR structure without any biasing network. When the state of diode is OFF, the planar monopole antenna changes to the UWB mode, and when the diode is turned ON, a frequency notch is created at 5–6 GHz. The state of diode is set to the “ON” state dynamically in the presence of a 5–6 GHz RF signal that is detected by using a wireless power management unit (PMU) that contains a broadband rectenna and a DC-DC passive booster. The rectenna consists of a novel cypress-shaped monopole antenna as a signal receiving part and two sub-rectifiers which are connected to a 3 dB branch-line coupler with a grounded isolation port. The antenna switches from UWB to single band-notched when an RF input signal (≥8.5 dBm) in the 5.25 GHz is sensed by the RF PMU with a conversion efficiency of 26% and DC output voltage of 0.36 V, and it fades immediately in real time when the external RF signal is eliminated. In the three-tone signals, the efficiency and input signal improvements are about 10% and −5.5 dBm in the low-power levels, especially, and so develop and enhance the performance of the dynamic reconfigurability.

The gain properties of an axially slotted cylinder coated with two lossless layers and embedded in a certain lossless background medium have been investigated analytically. The effects of different types of coating layers, i.e. dielectric, magnetic, and Single Negative materials upon the gain characteristics of an axial slot have been discussed. It is observed that if inner layer is either of dielectric or magnetic type and outer layer is an Epsilon Negative type having its relative permittivity of negative one and slotted cylinder is embedded in the free space then the gain has directive pattern. It is also studied that if both layers are dielectric or magnetic types and embedded in a Mu Negative medium then its gain pattern becomes more directive with the maximum gain in the forward direction.

An Nth-order tunable bandpass filter (BPF) structure with extended passband bandwidth has been proposed in this paper based on the novel tunable resonator and coupling structure. The designed tunable resonator is composed of two coupled lines and one varactor diode, while the presented tunable coupling structure is constructed by two cascaded transmission lines and one short-circuited varactor diode. Moreover, the even-(odd-) method and lumped-element equivalent circuit are employed to analyze the operating mechanisms of the designed Nth-order tunable BPF. Specifically, the frequency tuning range is determined by the characteristic impedance and electrical length of coupled line when the varactor diode is within the fixed tuning range. Then, the design procedure for the Nth-order tunable BPFs is proposed. To demonstrate the presented idea, the second- and third-order fully tunable BPFs have been designed and simulated. Finally, a second-order tunable BPF with the compact size of 0.03λg × 0.13λg has been fabricated and measured, and the measured center frequencies are ranging from 0.91 to 1.46 GHz with the passband bandwidths wider than 11.2%.

A novel dual-band single-feed reconfigurable annular-ring slot antenna with polarization diversity is proposed. This antenna has the ability to switch frequency bands and polarization at the same time whereas applying a simple structure. It consists of two concentric circular slots and two tuning stubs on one side of the substrate and a 50 Ω microstrip feed line and two stubs on the other side. The proposed antenna can be switched between two resonant frequencies, 2.4 GHz (WLAN) and 3.5 GHz (Wimax). Furthermore, it can be switched between linear polarization (LP), left-hand circular polarization (LHCP), and right-hand circular polarization (RHCP) at the first frequency band, LHCP and RHCP at the second band. All these capabilities are achieved by applying only five PIN diodes on both sides of the substrate. Simulation and experimental results indicate that the proposed antenna demonstrates a good impedance bandwidth at the two frequency bands and satisfactory radiation pattern in five different states.

This article analyzes and describes phase nonlinearity reduction techniques in detail for ultra wideband complex receivers to qualify airborne system requirements. Phase nonlinearity directly affects the final frequency resolution coming from unknown threats. Thereby, the reduction of phase nonlinearity of all radio frequency (RF) channels including phase correlators is very essential. A simple phase nonlinearity calculation step has been shown in this article without taking the help of any coding (software). A detail excel sheet–based phase nonlinearity calculation has been explained and estimated with examples. Power and phase corrections are especially done to keep the RF response flat over a wide frequency spectrum to enhance better phase linearity. This is done by designing various equalizers with different slope gradients and adjusting power levels by using attenuation pads or reducing feeds by other means. Phase nonlinearity has been kept under control by tracking the phase of mixers, other passive/active components within ±5°, and all the RF channels within ±15°. The power level has been adjusted within P1dB or just beyond the P1dB to keep the harmonic level less, which in turn controls phase nonlinearity in all the active devices. The performance of phase correlators against various power levels has been analyzed to finalize uniform RF and LO power levels (feed) at the input of the phase correlators. The level of uniform feed has been decided after reviewing phase nonlinearity responses of the correlators. Thus, the final resolved frequency become accurate (<3 MHz root mean square). Finally, four receivers have successfully been developed and evaluated over temperature (−40°C to +71°C) and vibration to establish the method for mass production.

In this work, a low profile ultra-wideband (UWB) antenna is designed and investigated using a novel loop-based wideband artificial magnetic conductor (WB-AMC) for gain enhancement. Initially, a compact loop antenna is designed using stub loading and further optimized for the UWB range by applying curve ground methodology. The average gain of the proposed antenna without WB-AMC is 2.7 dBi. To enhance the gain of the entire UWB range, loop-based WB-AMC in [2 × 2] forms is integrated. WB-AMC is used as a ground plane beneath the antenna. To validate the performance, the UWB antenna and WB-AMC are fabricated and tested. The measured results confirm the entire UWB range. Proposed antenna provides a peak gain of 9.4 dBi and an average gain of 5.8 dBi. Vertical profile reduction of 50% is achieved compared to perfect electric conductor ground. The proposed UWB antenna is a potential candidate for UWB wireless applications due to its attractive features such as low profile, wide bandwidth coverage, omnidirectional pattern, constant high gain, and group delay.

Electromagnetic characteristics of the E-plane T-junction for two rectangular waveguides using resonant coupling between the waveguide sections were studied by mathematical modeling. The problem of coupling between infinite and semi-infinite rectangular waveguides through a resonant slot in the end-wall of the semi-infinite waveguide in the presence of resonant monopole is solved in a strict electrodynamic formulation. The monopole with variable surface impedance is placed parallel to the narrow walls at an arbitrary position inside the infinite waveguide. The problem is solved analytically by the generalized method of induced electro-magneto-motive forces. Impedance vibrator inclusions with variable electro-physical parameters have been analyzed as control elements for waveguide junctions. To this purpose energy characteristics of the junction in the single-mode regime of the both waveguides, and also in multi-mode regime of the semi-infinite waveguide is investigated. The results may be useful for development of variety antennas and waveguide devices, which involves waveguide junctions.

We present a study on using carbon nanotubes (CNTs) as the radiating part of resonant antennas in order to reduce their dimensions. A mesoscopic electromagnetic (EM) model for CNTs was developed to allow the simulation of RF devices in classical EM solvers while retaining the specific properties of CNTs. A circuit approach is also used to provide a physical interpretation of the results on monopole antennas and trend prediction. These techniques constitute a platform to study the trends and trade-offs involved in the design of these antennas. Finally, these results are used to assess suitable fabrication techniques for CNT-based short resonant antennas and conclusions are drawn on their potential applications.

Resonant Bessel-beam launchers (BBLs)are radiating devices constituted by a cylindrical metallic cavity with a partially reflecting sheet (PRS) on top. Millimeter-wave resonant BBLs typically exhibit transverse magnetic (TM) polarization due to the use of coaxial probes as feeders and homogenized metasurfaces as PRS. Launchers showing either a purely transverse electric (TE) or a hybrid (quasi-TE) polarization have recently been proposed for realizing wireless power transfer (WPT) links in the radiative near-field region at millimeter waves. The former are obtained by means of a radial slot array as a feeder and a homogenized metasurface as a PRS. The latter are obtained by using a loop antenna as a feeder and an annular strip grating in the homogenization limit as radiating aperture. In this work, based on an original semi-analytical model, such a metasurface is demonstrated to show a dichroic behavior. This interpretation explains the improvement in terms of polarization purity with respect to more nondichroic conventional homogenized metasurfaces. The behavior of the annular strip grating under a pure TM polarization is tested with a coaxial feeder, whereas its behavior under a pure TE polarization is tested by means of the radial slot array feeder. Results confirm the validity of the proposed analysis, which is finally exploited to evaluate the WPT performance.