A compact coplanar waveguide-fed monopole antenna is presented in this paper. The proposed antenna is composed of three monopole branches. In order to achieve the miniaturization, the longest branch was bent. The antenna is printed on an FR4 dielectric substrate, having a compact size of 0.144λ0 × 0.105λ0 × 0.003λ0 at its lowest resonant frequency of 900 MHz. The multiband antenna covers five frequency bands: 820–990 MHz, 1.87–2.08 GHz, 2.37–2.93 GHz, 3.98–4.27 GHz, and 5.47–8.9 GHz, which covers the entire radio frequency identification bands (860–960 MHz, 2.4–2.48 GHz, and 5.725–5.875 GHz), Global System for Mobile Communications (GSM) bands (890–960 MHz and 1.850–1.990 GHz), WLAN bands (2.4–2.484 GHz and 5.725–5.825 GHz), WiMAX band (2.5–2.69 GHz), X-band satellite communication systems (7.25–7.75 GHz and 7.9–8.4 GHz), and sub 6 GHz in 5G mobile communication system (3.3–4.2 GHz and 4.4–5.0 GHz). Also, the antenna has good radiation characteristics in the operating band, which is nearly omnidirectional. Both the simulated and experimental results are presented and compared and a good agreement is established. The proposed antenna operates in five frequency bands with high gain and good radiation characteristics, which make it a suitable candidate in terminal devices with multiple communication standards.

In this paper, design, manufacture, and measurement of a wideband matching network for a broadband V-shaped square planar monopole antenna (V-SPMA) is presented. Matching network design is unavoidable in most cases even vital to facilitate a maximally flat power transfer gain for an antenna. In the work, a bandpass matching network (BPMN) design is done for a particular square monopole antenna with V-shaped coupling element that has essentially bandwidth increasing effect. Designed BPMN and the antenna forms a VSPMA–BPMN matched antenna structure. “real frequency technique” is employed in the BPMN design. BPMN prototype circuit has been constructed on an FR4 laminate with commercial microwave chip inductors and capacitors. Vector network analyzer gain and reflectance measurements of the matched antenna structure have shown highly compatible results to those of the theoretical design simulations along the passband (~0.8–4.7 GHz). Furthermore, newly proposed distributed capacitor–resistor lossy model for microstrip lines used in the BPMN circuit have exhibited that it can successfully mimic the measured gain and reflectance performance of the matched structure in passband and even in stopband upto 8 GHz. Designed structure can be utilized as a one single wideband broadcasting medium suitable for many communication standards such as GSM, 3G, and Wi-Fi.

This paper investigates the performance of 3D-printed dielectric reflectarray antennas (RAs) with wideband behavior and beam-steering capabilities. The designed unit cell consists of a single-layer dielectric element perforated with a square hole, whose side is used to control the local variation of the reflection coefficient. The numerical analysis of the unit cell and of first $52\times52$ reflectarray working in Ka-band, whose scanning capabilities are tested just moving the feed along an arc, confirms that the unit cell has a stable behavior with respect to both the frequency and the direction of arrival of the incident field. In view of these promising capabilities, the proposed unit cell is used to design a bifocal reflectarray with the same size and working in the same frequency band of the first one. Its numerical characterization and the measurements of a prototype prove that the RA is able to provide less than 0.8 dB of gain losses over a scanning range of ±40∘ in the vertical plane, while the bandwidth varies between 13.5% and 28%, depending on the pointing direction. The obtained results demonstrate the effectiveness of the proposed approach and highlight the potential of 3D-printing technology for producing high performance, cost-effective RAs with wideband behavior and excellent beam-steering features.

This paper presents a continuous frequency tuning Fabry–Perot Cavity (FPC) antenna of which the operating frequency can be varied from 4.87 to 5.84 GHz (18.1%). The cavity of the proposed antenna is excited by a double-layer antenna structure, which is made up of a main square patch and a parasitic one. The superstrate is a frequency-selective surface, consisting of 6 × 6 square-patch-type unit cells. The frequency tuning property is realized by employing 48 phase-changing elements placed around the main patch, which forms a reconfigurable high impedance surface (HIS). By controlling the biasing voltages of the varactors inserted in the HIS element, its capacitances and reflection phases can be varied continuously, which leads to a variation of the operating frequency. An antenna prototype has been fabricated and measured for validation. The measured results are in good agreement with the simulated ones. In the frequency tuning range, the measured realized gains have a smaller variation from 10.2 to 14.1 dBi compared with other reported frequency tuning FPC antennas.

To protect a worst-case user, Satellite-Based Augmentation System (SBAS) transmits inflated integrity information for protection level computation. In this work, a novel user-based technique for autonomous protection level computation is proposed. Its quality is examined over Key Performance Indicators tests for integrity and availability using real European Geostationary Navigation Overlay Service (EGNOS) data. The accomplished experiments confirm that this technique allows significant availability improvement without breaches of the integrity.

A circular patch antenna with wide impedance bandwidth and monopolar radiation pattern for indoor wireless communication is proposed and analyzed in this paper. The antenna is a combination of circular patch and four capacitive feeds. By incorporating a cross-connected shorted conducting strip over the circular patch, the proposed antenna provides an enhanced impedance width of 65.4%, ranging from 1.46 to 2.88 GHz. Four capacitive feeds improve the design flexibility and make the ripple of horizontal radiation pattern less than 3 dB. A prototype of the proposed structure has been fabricated and measured. Both the simulated and measured results show that the proposed design has a stable monopolar radiation pattern over a wideband frequency range and a peak gain of 5.0 dBi, which can be widely applied for indoor wireless communication such as GSM1800, CDMA2000, WCDMA, and TD-LTE systems.

This paper presents an active Q-enhanced LC dual-band band-pass filtering approach using parallel synthesis techniques at X- and Ku-bands in 0.13 µm SiGe BiCMOS technology. By employing two independently tunable parallel LC-tanks with either in-phase and out-of-phase addition, independently tunable dual-band filtering is achieved. For higher out-of-band (OOB) attenuation, subtraction of the two 2nd-order bandpass filter is implemented. The two bands are independently tunable in terms of Q and center frequency. The dual-band filter at 9.7 GHz and 13.9 GHz achieves a normalized dynamic range of 165–154.5 dB.Hz with an OOB attenuation of >50 dB below 3 GHz. In between the two bands, the attenuation is 22 dB when the two passbands have 200 MHz bandwidth each. The total group delay is 0.8 ns and 1.9 ns for Q of 20 and 50, respectively. The filter achieves better OOB rejection with wider band channels at X- and Ku-bands compared with state of the art integrated filters. The filter consumes 115–130 mW of DC power. The core die area is 0.53 × 0.7 mm2.

A design of a microwave absorber based on frequency selective surface resonating in X-band having ultrathin thickness, polarization controlled behavior, and increased absorption bandwidth has been reported. The reported absorber having its unit cell embodied of multiple resonating structures which includes conventional square, circular, and butterfly shaped resonators resulting in three absorption apexes at 9.44, 10.00, and 10.53 GHz (all in X band) with 99.9%, 99%, and 95.1% of absorptivity obtained at the frequencies of resonances. It demonstrates a wide full width at half maximum having 1.48 GHz as bandwidth, at the expense of using an ultrathin substrate of 0.0096 λ0, where λ0 is the wavelength with respect to lowest resonating frequency, i.e. 9.44 GHz. The unit cell is fourfold symmetric exhibiting independence about the absorber’s polarity, as well as, it behaves stable over the outspread angle up to 45 degrees for both transverse magnetic and transverse electric polarized wave under sloped incident angle. The absorption behavior has been demonstrated by plotting the distribution of surface-currents and electric fields at the frequencies of resonance. The fabricated prototype of the presented design is tested at X-band and the obtained results concur with the simulated results.

In this article, the cylindrical conformation of a linearly polarized cavity-backed magnetoelectric (ME) antenna is studied. Starting from a planar ME antenna presenting a wide bandwidth due to a specific design of its feeding probe, the impact of conformation is shown; the coupling between the ME dipole and the cavity walls is demonstrated to be the key element to keep a wideband behavior. Conformal antennas offering the same impedance bandwidth as the planar antenna are presented operating at Global Navigation Satellite System frequencies (1.164–1.61 GHz). As a result of the conformation, the antenna size has to be reduced to maintain the coupling and a wideband behavior. A prototype conformed to a 44-mm radius cylinder was built using low-cost additive manufacturing. External dimensions of 62 × 62 × 35 mm3 (0.285 × 0.285 × 0.16λ03, where λ0 is the wavelength at 1.38 GHz) were obtained, showing a ground plane area reduction of 46% compared to the planar antenna with the same materials. The conformal antenna also exhibits very steady radiation properties with a gain of around 4.5 dBi and a very similar and stable 3 dB beamwidth around 113° in E- and H-planes. A relatively good agreement is found between measurements and simulation.

We present a technique allowing the stabilization and tuning of a modulation sideband in the presence of high-carrier frequency jitter and increased carrier phase noise. This technique is of particular interest in communication systems where oscillators providing the carrier signal cannot be stabilized by a conventional phase-locked loop, such as systems relying on low-cost optical LO generation techniques. The results obtained in simulation are validated by measurements carried out on a modular system demonstrator.

In this paper, we propose a novel energy detection (ED) receiver architecture combined with time-of-arrival (TOA) estimation algorithm, compliant to the IEEE 802.15.4a standard. The architecture is based on double overlapping integrators and a sliding correlator. It exploits a series of ternary preamble sequences with perfect autocorrelation property. This property ensures coding gain, which allows an accurate estimation of power delay profile (PDP). To improve TOA estimation, the interpolation of PDP samples is proposed and the architecture is validated by using an ultra-wideband signals measurements platform. These measurements are carried out in line-of-sight and non-line-of-sight multipath environments. The experimental results show that the ranging performances obtained by the proposed architecture are higher than those obtained by the conventional architecture based on a single-integrator in both LOS and NLOS environments.

This paper presents a broadband Butler-based slant ±45° dual-polarized omni-directional antenna working at the frequency band of 1.69–2.69 GHz for extending wireless communication network capacity in the limited service size. The proposed antenna realizes a 360° full coverage with wider bandwidth in a compact cylinder and increases the network capacity to 6 × 6 MIMO instead of using three traditional 2 × 2 MIMO omni-directional antennas. Theoretical analysis, simulation, and fabrication are conducted to validate the idea of the proposed omni-directional antenna. The measured results show 46% bandwidth with 15 dB return loss, 2.2 dB azimuth null and 8.9–10.5 dBi gain for port-C with 0° phase increment, and 14.1 dB azimuth null and 9.6–10.6 dBi gain for port-L/R (left/right) with ±120° phase increment, respectively.

This paper presents switched sequential amplifiers (SSAs) using reconfigurable directional couplers as power splitters and combiners. The SSA concept allows matching the efficiency characteristics to the amplitude probability density distribution of the applied modulated signal. Therefore the back-off efficiency can be increased significantly. A three-channel SSA can e.g. theoretically achieve a −10 dB back-off efficiency exceeding 50%. Design parameters and potential efficiency enhancement are discussed for two- and three-channel SSAs. After a brief introduction of the used switched couplers, the circuit concept for two- and three-channel SSAs is described. Calculations for the possible efficiency enhancement are presented. Also signal distortions by the directional couplers are outlined. The paper closes with experimental results for a two-channel SSA.

Jamming of synthetic aperture radar (SAR) is more difficult than the conventional radars because of its high processing gain. The defocusing of fake or virtual scatterers is the main problem that any jamming technique needs to tackle. An algorithm based on fractional Fourier transform is proposed for the efficient jamming of SAR. The results show that the performance of proposed algorithm is better than conventional Range Doppler Algorithm.

This article introduces an innovative approach to antenna array design, focusing on synthesizing the optimal radiation pattern for fifth-generation (5G) communication. The authors have designed a reliable linear and elliptical antenna array (EEA) of dipole elements by employing sailfish optimization (SFO). 5G technology promises transformative improvements in wireless communication with high data rates, expanded capacity, minimal latency, and exceptional service quality. The crux of 5G lies in the precision of antenna array design, aiming for an emission pattern with minimal side lobe levels (SLLs) and a narrow half-power beam width (HPBW). A narrower HPBW is essential for efficient long-range communication, whereas reducing the SLLs enhances signal clarity. The SFO optimizes the current excitation of each antenna element for reducing the mutual coupling effects and lowering the SLL and HPBW values in linear and EEAs. This paper uses the exact excitation to each element to show the linear antenna arrays (LAA) (10-, 16-element) design examples and EAA (8-, 12-, 20-element) structures. The LAA and EAA design examples obtained with the SFO algorithm establish the advancement in SLL suppression over the uniform antenna array and the methods proclaimed in the recent article.

This paper outlines the results of particle-in-cell simulations of a relativistic magnetron with six cavities and a transparent cathode configuration. Excitation of the π mode in the interaction region was attained, which in turn led to $\textrm{TE}_{11}$ mode emission of microwaves to the waveguide. This mode transformation was achieved with a non-symmetric diffraction output, consisting of four large and two small tapered cavities. Simulations were performed with a voltage across the anode-cathode gap varying from 164 to 356 kV, and axial magnetic field strengths between 0.24 and 0.34 T. Maximum efficiency of 37% was obtained with a peak output power of 590 MW, having a voltage of 261 kV and a magnetic field of 0.30 T. Furthermore, a frequency of 2.57 GHz and a rise time of microwaves at the waveguide of 15 ns were demonstrated. The electron leakage current was shown to decrease from ∼10$\%$ to less than $1\%$ when employing a longer interaction region, while still exhibiting good performance. Additionally, we show that there is an optimal range of voltages given a magnetic field, for which π mode excitation with high efficiency is attained.

Normally, the reported gain of the microstrip patch antenna is within 8 dBi. Using properly located three shorting pins on three bisectors, the present work reports a method to convert the non-radiating TM11 mode of equilateral triangular patch antennas (ETPAs) to a deformed TM11 radiating mode. The boresight gain of ETPA operating in TM11 mode is enhanced from −10.75 to 12.1 dBi at 5.43 GHz. The boresight measured gain is further enhanced to 14.2 dBi at 5.52 GHz by using a triangular surface-mounted short horn (SMSH) of about ${{\lambda }}/5$ height. The aperture efficiency of the ETPA with the shorting pins is 84.2%. The aperture efficiency is further improved to 94.2% using the SMSH. The measured boresight cross-polarization and side-lobe level are −40 and −29 dB, respectively. The nature of the electricfield and surface current distribution is analyzed, using both the characteristic mode analysis method and high-frequency structure simulator, to understand the role of shorting pin and coaxial feed in converting the non-radiating TM11 mode to the radiating mode. A systematic design process also is presented for a fast design of shorting pin-loaded ETPA on the suitable substrate at a specified frequency.

We present the design, fabrication, and measurement of a 2-way modified Wilkinson divider constructed in a coplanar geometry exhibiting ultra wideband isolation, transmission, and port matching in the millimeter-wave frequency range. The proposed divider replaces the lumped resistor in the conventional Wilkinson divider with two quarter-wave length transmission lines, a phase inverter, and two 2Z0 resistors. Except for the three ports that are coplanar waveguides (CPWs), the main body of the divider uses coplanar striplines (CPS). The phase inverter is realized using a simple airbridge-based crossover which is compatible with a modern monolithic microwave integrated circuit process. The divider has a ring-like configuration fabricated on a 620 µm thick semi-insulating GaAs wafer using electron beam lithography (EBL) technology. Three-dimensional (3D) full-wave electromagnetic simulations have been carried out to optimize the design and investigate the possible effect of fabrication tolerance on the performance of the crossover and the divider. Two dividers working at center frequencies of 25 and 80 GHz have been designed, fabricated, and tested. They all show consistent performance in terms of bandwidth, isolation, and port matching. Experimental and simulation results are in excellent agreement.

In this paper, we present a near-field microwave microscopy method for the characterization of dielectric materials samples in the Industrial, Scientific and Medical (ISM) band. The system proposed is composed of a probe coupled to a dielectric resonator (DR) operating in the TE011 mode. Latter this is used to fix the resonance frequency of the resonator at 2.45 GHz. This system is used for the characterization of dielectric samples with accuracy and high spatial resolution, knowing that they do not have predetermined forms, but a small plane surface.The same device is used for a multi-frequency characterization (4–20 GHz) using resonance frequencies of the cavity instead of one resonance frequency of the DR.

The narrow bandwidth of microstrip antennas is one of the most important features that restrict its wide usage. This paper presents a new coplanar waveguide-fed compact rectangular microstrip antenna with the improvement of the bandwidth using the slot geometry and cutting rectangular periodic edges for the patch radiator. To develop this structure, we have conducted many optimization and investigation using Momentum Software integrated into ADS “Advanced Design System” and comparison of the results with CST Microwave Studio. The comparison between the simulation and measurement results permits to validate the final achieved antenna with an improvement of the bandwidth. This antenna has wide matching input impedance ranging from 1.7 to 3.5 GHz with a return loss less than −10 dB, corresponding to bandwidth 69.7% at 2.6 GHz as a frequency center. The antenna achieved is a low cost, planar, and easy to be fabricated, thus promising for multiple applications in wireless communication systems. Details of the proposed antenna design and both simulated and experimental results are described and discussed.