This article presents the results of the first AIAA Stability and Control Prediction Workshop obtained at the U.S. Air Force Academy using the kCFD flow solver of the ${\rm{HPCMP}}\;{\rm{CREAT}}{{\rm{E}}^{{\rm{TM}}}}$ -AV Kestrel simulation tools. The test case considered is a large-scale Common Research Model (CRM) tested at the ONERA S1MA wind tunnel at different transonic speeds and fixed lift coefficient values at zero and non-zero side-slip angles. The computational results include a grid sensitivity analysis and validation with available experimental data. In addition, the Mach number and sting effects on the predicted stability and control values of the test case are investigated. Finally, a system identification method using a regression model is developed and used for prediction of stability and control data. The regression coefficients are estimated from an input signal with varying-frequency changes in the angle-of-attack, pitch rate, and side-slip angle. Once the model was created, it was used to predict the static and dynamic aerodynamic data of the test cases. The results show that the model predictions match very well with calculated CFD data at discrete flow conditions.

During the past two decades, with the advancement of avionics, control systems, design, product methods, and communication systems, UAVs have gained more interest from both civil and military customers. Hence, more researchers have dedicated their time to developing new applications for drones and improving their performance. In this study, a literature review on drone applications is conducted. It is explained that they can be more effective and beneficial when merged with preexisting systems, and thus making a system of systems. Further, we have classified UAV applications more comprehensively. This classification can be very useful for providing insights when designing new UAVs. Finally, previous works are discussed thoroughly and diagrams are developed to show the research focus in this field. These statistical diagrams can also be used as a gap analysis tool.

There are many factors causing the shimmy of the aircraft landing gear and structural clearance of landing gear is a typical factor. Some aircraft in service or operation did not shimmy before, but suddenly appeared after a period of use. To solve the problem of clearance shimmy during the service of a certain aircraft, we established a dynamic model of rotating gear with clearance based on the flexible multi-body dynamics model of landing gear and L-N contact theory. We defined different types of clearance and established a mechanical model of aircraft pendulum vibration considering the clearance of landing gear structure for dynamic simulation, and studied the effects of different clearance types, clearance size of motion pair and different clearance positions on the stability of pendulum. The results show that the axial clearance has little effect on the shimmy performance of landing gear; the radial clearance has a certain effect on the shimmy performance of medium speed running, which slightly improves the shimmy damping required by medium speed running; the rotational clearance affects the shimmy performance of the nose landing gear by affecting the force transmission of structural components. The required shimmy damping coefficient increases at low speed and decreases at high speed. The main reason for the return clearance is that during the return, the shimmy damper does not work, which leads to the decrease of the shimmy damping performance and the increase of the required shimmy damping coefficient in the whole speed range. Meanwhile, the structural clearance will increase the shimmy frequency of the nose landing gear. By analysing the yaw angle of the nose landing gear and the time domain curve of the yaw angle of the yaw damper, we can determine which structure of the landing gear and which type of clearance is the cause of the yaw. Finally, the coupling effect caused by the main structural parameters of the landing gear in “gap shimmy” was analysed according to different mechanical stability distances and strut stiffness of the nose landing gear, providing reference for aircraft anti-shimmy design, nose landing gear fault diagnosis and nose landing gear maintenance support.

The unmanned aerial vehicle (UAV) flocking among obstacles was transferred to a velocity-controllable UAV flocking problem, which means that multi-UAV gradually form and maintain the $\alpha$ -lattice geometry as they track the desired flocking velocity, and can be applied to tasks such as obstacle avoidance and velocity tracking. Velocity-controllable UAV flocking problem is a multi-objective flocking controller parameters optimisation problem, for which we design flocking velocity and geometry objective function, and solve them using a multi-objective particle swarm optimisation algorithm (MOPSO). On this basis, to address the problem that MOPSO has random results and long computation time, we propose to use a neural network (NN) to approximate the mathematical relationship between the UAV flocking state and the flocking controller parameters. We simulate the flight process of 5 and 49 UAVs performing obstacle avoidance and velocity tracking tasks, respectively. The results show that the proposed UAV flocking controller has better convergence performance, obtains reproducible results, reduces computation time, and can be used for large-scale UAV flocking control.

In view of the cooperative guidance problem with time delay, this paper proposes a two-stage time-delay prescribed-time cooperative guidance law in the three-dimensional (3D) space. In the first stage, by introducing a time scaling function and time-delay consensus, the proposed cooperative guidance law can overcome the negative influence of time delay to guaranteed the desired convergence performance. Derived from the Lyapunov convergence analysis, the time-delay stability of the first stage can be ensured and the convergence time can be described as the relationship between delayed time and mission-assigned convergence time. Then, taking the prescribed-time-related convergence time as the switching point, the second stage begins with suitable initial conditions and all interceptors are governed by proportional navigation guidance. Finally, comparative simulations are performed to demonstrate the effectiveness and superiority of the proposed time-delay guidance law.

The boundary layer thickness on a compressor blade suction surface increases rapidly under a adverse pressure gradient and even separates from the blade surface. This paper proposes a novel method for developing the slot inside the blade, with the inlet of the slot located at the leading edge of the blade and the outlet located at the suction surface, using the momentum of the incoming flow to form a high velocity jet to control the boundary layer on the suction surface. For a plane cascade with a diffusion factor of 0.45, the effects of the main slot parametres (such as the shape of the slot and the positions of the slot inlet and outlet) on the flow in the slot, the flow field and the aerodynamic performance of the cascade were investigated with a numerical method. When the aerodynamic performance of cascades with slotted and unslotted blades was compared, it was found that a reasonable slot structure can effectively inhibit the development of the boundary layer on the blade suction surface and greatly improve the aerodynamic performance of the cascade. Based on the influence of the slot parametres of the above cascade, the slot of a plane cascade with a diffusion factor of 0.60 was designed. The numerical calculation results show that the slotted cascade with a diffusion factor of 0.60 outperformed the slotted cascade with a diffusion factor of 0.45. This result showed that the higher the cascade load, the greater the performance improvement from slotting. Furthermore, the unslotted and slotted cascades were tested, and the test results agreed well with the calculations. The aerodynamic performance of the slotted cascade was better than that of the unslotted cascade, which verifies the accuracy of the calculation method and the feasibility of blade slotting for suppressing the development of boundary layers on suction surfaces and reducing flow loss.

This paper presents a relative fuel burn evaluation of the transonic strut-braced-wing configuration for the regional aircraft class in comparison to an equivalent conventional tube-and-wing aircraft. This is accomplished through multipoint aerodynamic shape optimisation based on the Reynolds-averaged Navier-Stokes equations. Aircraft concepts are first developed through low-order multidisciplinary design optimisation based on the design missions and top-level aircraft requirements of the Embraer E190-E2. High-fidelity aerodynamic shape shape optimisation is then applied to wing–body–tail models of each aircraft, with the objective of minimising the weighted-average cruise drag over a five-point operating envelope that includes the nominal design point, design points at $\pm 10\%$ nominal $C_L$ at Mach 0.78, and two high-speed cruise points at Mach 0.81. Design variables include angle-of-attack, wing (and strut) twist and section shape degrees of freedom, and horizontal tail incidence, while nonlinear constraints include constant lift, zero pitching moment, minimum wing and strut volume, and minimum maximum thickness-to-chord ratios. Results show that the multipoint optimised strut-braced wing maintains similar features to those of the single-point optimum, and compromises on-design performance by only two drag counts to achieve up to 11.6% reductions in drag at the off-design conditions. Introducing low-order estimates for approximating full aircraft performance, results indicate that the multipoint optimised strut-braced-wing regional jet offers a 13.1% improvement in cruise lift-to-drag ratio and a 7.8% reduction in block fuel over a 500nmi nominal mission when compared to the similarly optimised Embraer E190-E2-like conventional tube-and-wing aircraft.

In this study, an active defence cooperative guidance (ADCG) law that enables cheap and low-speed airborne defence missiles with low manoeuverability to accurately intercept fast and expensive attack missiles with high manoeuverability was designed to enhance the capability of aircraft for active defence. This guidance law relies on the line-of-sight (LOS) guidance method, and it realises active defence by adjusting the geometric LOS relationship involving an attack missile, a defence missile and an aircraft. We use a nonlinear integral sliding surface and an improved second-order sliding mode reaching law to design the guidance law. This can not only reduce the chattering phenomenon in the guidance command, but it can also ensure that the system can reach the sliding surface from any initial position in a finite time. Simulations were carried out to verify the proposed law using four cases: different manoeuvering modes of the aircraft, different speed ratios of the attack and defence missiles, different reaching laws applied to the ADCG law and a robustness analysis. The results show that the proposed guidance law can enable a defence missile to intercept an attack missile by simultaneously using information about the relative motions of the attack missile and the aircraft. It is also highly robust in the presence of errors and noise.

A novel method of determining the crack tip location from a thermoelastic quadrature signal is presented. The method is utilised for crack tip locations within complex stress fields, namely within fastened aircraft lap joints. Coupled structural-thermal finite element modelling was undertaken to investigate the thermal response field around the crack tip location and develop the algorithmic principles. Experimental validation of the crack tip location was conducted using established crack mouth compliance techniques and optical measurements. The crack tip finding algorithm used the location of the maximum spatial gradient of the thermal field in the direction of crack growth. The method showed good accuracy when compared to traditional methods. Resultant crack growth rates were further verified using quantitative fractography.

Avian radar systems are effective for wide-area bird detection and tracking, but application significances need further exploration. Existing radar data mining methods provide long-term functionalities, but they are problematic for bird activity modelling especially in temporal domain. This paper complements this insufficiency by introducing a temporal bird activity extraction and interpretation method. The bird behaviour is quantified as the activity degree which integrates intensity and uncertainty characters with an entropy weighing algorithm. The method is applicable in multiple temporal scales. Historical radar dataset from a system deployed in an airport is adopted for verification. Temporal characters demonstrate good consistency with understandings from local observers and ornithologists. Daily commuting and roosting characters of local birds are well reflected, evening bat activities are also extracted. Night migration activities are demonstrated clearly. Results indicate the proposed method is effective in temporal bird activity modelling and interpretation. Its integration with bird strike risk models might be more useful for airport safety management with wildlife interference.

This paper presents a fault detection and diagnosis (FDD) algorithm for various faults in the primary air data sensors (PADS) of an aircraft in the presence of external disturbances such as atmospheric turbulence. Rapid wind variations due to turbulence induce excessive error in the externally fitted air data probe measurements, which may lead to loss of control and misinterpretations by the flight crew. In adverse environmental conditions, the FDD of air data prefers robust and adaptive air data estimates that use an analytical redundancy approach with fewer computations. The proposed method considers the kinematics of the aircraft instead of the dynamics used in the state-of-the-art algorithms. The advantage of using kinematics is that it can reduce modeling errors significantly, avoiding high false alarm rates in the FDD process. For the estimation of stable and accurate air data under external disturbance, the inertial navigation system and global positioning system (INS/GPS) output are considered instead of actual air data probe or sensor measurements. The proposed algorithm uses estimates of air data using an exponentially weighted adaptive extended Kalman filter (EW-AEKF) to detect and diagnose PADS faults, which can perform well even in the presence of uncertain noise due to atmospheric turbulence experienced during flight. The simulation was carried out to validate the algorithm with flight data obtained from the X-Plane flight simulator under moderate atmospheric turbulence. The simulation experiments were carried out using the MATLAB programming platform. The results show that the proposed method achieves satisfactory FDD performance with lower root mean square error (RMSE) and computation time than traditional EKF-based algorithms.

As a basic flow model for engineering applications, wall-bounded turbulent flow has been widely studied in the field of aero-optics, but the flow control methods that could effectively suppress aero-optical effects are relatively rare. As an urgent requirement in engineering application, the concept of the steady wall blowing and suction is proposed by the author. Firstly, the author briefly described the flow model and physical method. Secondly, the choice of disturbance type is given. Then, the results of wall blowing-suction, suction and blowing ways based on steady and unsteady disturbance are compared. Finally, it is concluded that employing the high steady wall blowing disturbance (A = 0.2) could realise aero-optical suppression by around 20%. Besides, the steady wall suction scheme contributes to about 70%–80% reduction effect within a wide amplitude range (A = 0.2–1.0), which suppresses this effect by maintaining laminar state downstream contrasted by the baseline case.

The pulsed jet is a novel and effective active mixing enhancement approach. For the transverse pulsed jet in the supersonic crossflow, the frequency influence is investigated using the three-dimensional Reynolds-averaged Navier–Stokes (RANS) equations coupled with the SST k-ω turbulence model. The averaged flow field properties of the pulsed jet are better than those of the steady jet when considering mixing efficiency and jet penetration depth, especially for the case with the pulsed frequency being 50kHz. The flow field structures of the pulsed jet are connected with the time, with periodic wave structures generating in the flow field and moving downstream. The size of the wave structures and its distance are related to the frequency, namely the size and flow distance are relatively small at 50kHz, and it takes some time for the pulsed jet to establish its influence in the full flow field. At low frequencies, the flow field produces large fluctuations, and this may be detrimental to the stable operation of the engine.

Unmanned Aerial Vehicles (UAVs) have been used extensively in many applications, such as surveillance, medical transportation and delivery tasks. These applications usually involve an attachment system to connect a payload. However, when connected to such a coupled system, the UAV exhibits lower flight performance mainly due to gust loads. Mathematical modeling is used in this paper to illustrate the comparison between an UAV with a coupled system and a conventional UAV. Proportional Derivative (PD) and Sliding Mode Control (SMC) approaches are used to evaluate the vibrations of the payload, and the UAV trajectory subjected to Dryden gust. This work therefore uses these methods to investigate the dynamic response of a quadrotor-type UAV equipped with a payload and a flexible attachment system.

This study presents a mathematical model that schedules arrival aircraft regarding RECAT-EU that is new categorisation for applying separation minima and analyses its effect on the performance of the Point Merge System (PMS) at Sabiha Gökcen International Airport (LTFJ). There are two main scenarios: one of them uses RECAT-EU and the other employs the ICAO wake turbulence category. Both scenarios have ten different test problems to examine the mathematical model. The model applies RECAT-EU wake turbulence categories and compares the outcome with the ICAO wake turbulence categories. The model aims to minimise flight duration on the sequencing leg and ground delay in the departure queue using the RECAT-EU and ICAO wake turbulence categories individually. The results were analysed to reveal the PMS performance using the two different approaches to turbulence categories. Statistical analysis was also carried out to compare the means of the two groups in the model.

In this study, the aerodynamic performances and the flow separation behaviour of the wing profiles, used in the wing of Boeing 737-Classic aircraft, and a model wing formed of these profiles were investigated at 2 × 105 Reynolds number (Re) and different angles of attack ranging from −4° to the angle, which maximum lift point obtained. The experiments were conducted in a low-speed wind tunnel in Erciyes University Faculty of Aeronautics and Astronautics Aerodynamic Laboratory. Four profiles and the model wing, which was obtained from the combination of the four profiles were produced in a rectangular shape with dimensions of 0.21m × 0.21m. In the first part of this two-part study, the wing profiles were examined individually regarding aerodynamic performance and flow separation. In the second phase of the study, the aerodynamic performance and the flow separation behaviour of the model wing were examined and the results were compared with the data obtained from each profile. The study results showed that the slopes of the numerical graphics are generally quite consistent with experimental results. In addition, the pressure and velocity distributions have followed the normal trend until the angle-of-attack (AoA) of 20°. In contrast, the negative speed values and negative pressure zones have appeared on the profile above this angle. The air flowed as laminar on the profiles and the model wing until 20°, while laminar separation bubbles are begun to take place at about 24° AoA. Finally, the best aerodynamic performance has been obtained with the model wing.

The purpose of this paper is to group the flight data phases based on the sensor readings that are most distinctive and to create a representation of the higher-dimensional input space as a two-dimensional cluster map. The research design includes a self-organising map framework that provides spatially organised representations of flight signal features and abstractions. Flight data are mapped on a topology-preserving organisation that describes the similarity of their content. The findings reveal that there is a significant correlation between monitored flight data signals and given flight data phases. In addition, the clusters of flight regimes can be determined and observed on the maps. This suggests that further flight data processing schemes can use the same data marking and mapping themes regarding flight phases when working on a regime basis. The contribution of the research is the grouping of real data flows produced by in-flight sensors for aircraft monitoring purposes, thus visualising the evolution of the signal monitored on a real aircraft.

This paper concentrates on the trajectory tracking problem for a stratospheric airship subject to underactuated dynamics, unmeasured velocities, modeling inaccuracies and environmental disturbances. First, a coordinate transformation is performed to solve the underactuated issue, which simultaneously permits a priori assignment of the tracking accuracy. Second, a finite-time observer is integrated into the control structure to offer the exact information of unmeasured velocities and uncertainties in an integral manner. Then, by combining the backstepping technique with the method of adding a power integrator, a new output-feedback control strategy is derived with several salient contributions: (1) the airship’s position errors fall into a predetermined residual region near zero within a finite settling time and stay there, while all the closed-loop signals maintain bounded during operation; and (2) no artificial neural networks and filters are adopted, resulting in a low-complexity control property. Furthermore, the presented method can be extended readily to a broad range of second-order mechanical systems as its design builds upon a transformed system model. Rigorous mathematical analysis and simulations demonstrate the above theoretical findings.

High-fidelity simulation tools have significant potential to support composite aircraft sustainment, though further study is required on incorporating the complex impact damage field. In this paper, compressive residual strength assessment is investigated using the high-fidelity computational tool BSAMTM. The experimental impact damage was mapped and modelled at a high-fidelity level, which included ply-by-ply definition of the geometry of the impact indentation, fibre fracture in the plies and delamination in ply interfaces. It was shown that applying a small lateral displacement or ‘pseudo-impact’ step was highly effective in generating matrix cracks in the impact region, which provided a suitably realistic representation of the interconnected damage map through-the-thickness. It was found that inclusion of all damage modes in the post-image damage map at a high-fidelity definition was essential due to the strong degree of interaction between damage modes. The results support improved sustainment of defence platforms, through enhanced predictive capability and understanding.

Many adaptations of the lifting-line theory have been developed since its conception to aid in preliminary aerodynamic wing design, but they typically fall into two main formulations, named $\alpha $- and $\Gamma $-formulation, which differ in terms of the control points chordwise location and the variable updated during the iterative scheme. This paper assess the advantages and drawbacks of both formulations through the implementation of the respective methods and application of standard verification and validation procedures. Verification showed that the $\Gamma $-method poorly converges for wings with nonstraight quarter-chord lines, while the $\alpha $-method presents adequate convergence rates and uncertainties for all geometries; it also showed that the $\Gamma $-method agrees best with analytic results from the cassic lifting-line theory, indicating that it tends to overpredict wing lift. Validation and comparison to other modern lifting-line methods was done for similar geometries, and not only corroborated the poor converge and lift overprediction of the $\Gamma $-method, but also showed that the $\alpha $-method presented the closest results to experimental data for almost all cases tested, concluding that this formulation is typically superior regardless of the wing geometry. These results indicate that the implemented $\alpha $-method has a greater potential for the extension of the lifting-line theory to more geometrically complex lifting surfaces other than fixed wings with straight quarter-chord lines and wakes constrained to the planform plane.