Short-channel Gallium Nitride (GaN) high-electron-mobility transistors (HEMTs) often utilize T-shape gates due to their large gate-line cross-sectional area and subsequent fMAX increase. In this paper, we report the linearity trade-offs associated with varying the T-gate geometries of AlGaN/GaN HEMTs on Si, specifically the gate extensions which serve as field plates and their impact on the large-signal performance. Small-signal characterization and modeling, in addition to TCAD, provide initial guidelines for the optimal dimensions for the gate field plates using the ratio of fT and the product of the gate resistance and the gate-to-drain capacitance. We utilize various characterization methods, including 6 GHz non-linear vector network analyzer characterization in addition to load-pull, to quantify the amplitude and phase distortion and their subsequent impact on the large-signal metrics of the devices under differing matching conditions and bias points. We deduce that the influence of the gate field plates on the amplitude and phase distortion is non-negligible, particularly under matched conditions.

Magneto-dielectric antennas (MDAs) provide small sizes, enhanced bandwidths, and frequency/polarization agility. We describe the fabrication and efficiency characterization at 0.4–0.8 GHz of five microstrip MDAs, whose gradually thicker substrates were 3D-printed using an off-the-shelf polylactic acid (PLA) filament doped with ferromagnetic particles. It was experimentally discovered that efficiency increases monotonically from 12% (−9.2 dB) to 37% (−4.3 dB) as substrate thickness goes from 1.6 to 4.3 mm; the rate is faster than expected for microstrip antennas. Numerical analysis indicated that the apparent magnetic loss tangent of the MD substrate experiences a threefold decrease as the 3D printer deposits more layers of iron-doped PLA. The MDAs exhibit radiation quality factors that are 3.7–7.2 times better than the dielectric counterparts. Moreover, a simple optimization of ground plane size could increase efficiency to 55% (−2.6 dB). The reduction in magnetic loss is attributed to a reduction in eddy current loss due to the separation of agglomerate iron particles. Therefore, despite the inherently lossy material used, the potential of 3D-printed MD substrates in providing acceptable antenna efficiencies is demonstrated together with unprecedented design freedom and fabrication flexibility.

We propose the techniques for automatic processing of measurement results in the context of golden (typical) device selection and noise figure measurement. These techniques are for golden (typical) device selection and noise figure measurement processing. Automation of measurement result processing and microwave element modeling speeds up a modeling routine and decreases the risk of possible errors. The techniques are validated through modeling of 0.15 μm GaAs pHEMTs with 4 × 40 μm and 4 × 75 μm total gate widths. Two test amplifiers were designed using the developed models. The amplifier modeling results agree well with measurements which confirms the validity of the proposed techniques. The proposed algorithm is potentially applicable to other circuit types (switches, digital, power amplifiers, mixers, oscillators, etc.) but may require different settings in those cases. However, in the presented work, we validated the algorithm for the linear and low-noise amplifiers only.

A cost-effective millimeter-wave measurement setup for narrowband path loss and angle-of-arrival measurements is presented in this paper. The setup consists of ubiquitous radio-frequency lab equipment and additional low-cost components. An algorithm is developed, which improves the measurement accuracy and reduces the required measurement time. An uncertainty analysis is performed, including a noise analysis, amplifier linearity, antenna misalignment and general system impairments. A theoretical model of the received signal plus noise is developed, which is used in Monte Carlo simulations to show the impact of snapshot averaging on the uncertainty. The estimated combined uncertainty with a 95.45% confidence level is 1.1 dB at the maximum measurable path loss and 0.3 dB in the case of low path loss, where the uncertainty due to receiver noise is negligible. The measurement setup is used in outdoor specular building reflection measurements at 24.00–24.25 GHz. The measured single-building reflections show a 1–9 dB excess loss compared to the free-space path loss. The measured excess loss is 9–20 dB for double-building reflections. These results indicate that buildings could potentially be used as effective millimeter-wave specular reflectors to extend millimeter-wave coverage.

This paper introduces a new maritime search and rescue system based on S-band illumination harmonic radar (HR). Passive and active tags have been developed and tested while attached to life jackets and a small boat. In this demonstration test carried out on the Baltic Sea, the system was able to detect and range the active tags up to a distance of 5800 m using an illumination signal transmit-power of 100 W. Special attention is given to the development, performance, and conceptual differences between passive and active tags used in the system. Guidelines for achieving a high HR dynamic range, including a system components description, are given and a comparison with other HR systems is performed. System integration with a commercial maritime X-band navigation radar is shown to demonstrate a solution for rapid search and rescue response and quick localization.

One of the current trends in the integrated circuit (IC) development is the integration of antennas on-chip or in the package of the IC. This poses challenges in the production testing process of the packaged IC, as the antenna functionality has to be included and at least one of the signal ports cannot be accessed at a conducted manner. In order to measure the reflection coefficient of an integrated antenna, a contactless characterization method (CCM) can be used. In this paper, the practicality of a CCM is assessed, having the application of a cost-effective high-volume testing procedure for integrated antennas in mind. It is shown that the CCM yields accurate results for different imperfections in the measurement setup. Moreover, measurement results around 33 GHz using a connectorized patch antenna are shown, which experimentally verify the validity of using the CCM under near-field conditions.

In this paper, an orthogonal frequency-division multiplexing (OFDM) waveform radar sensing approach is demonstrated based on field measurements at C-band. We demonstrate a concept that is based on the exploitation of typical wireless communication transmissions to perform passive, distributed radar sensing. Our concept is based on an OFDM radar that operates in the modulation symbol domain and can be well integrated into existing OFDM receivers. The measurement setup and the signal processing steps for the OFDM radar are described. The results show that the passive, distributed radar sensing approach can be used to detect and localize moving cars and even pedestrians in automotive intersection scenarios.

A novel 1 × 4 phased array elliptical inverted T-shaped slotted sectored patch antenna with defected ground structure (DGS), resonate at proposed ultra-wide tetra band at 28, 43, 51, and 64 GHz with high gain and beam-steering capabilities is presented. An inverted T-shaped slotted stub is used with the sectored patch to achieve ultra-wideband properties. In order to resonate the antenna at four different bands, DGS of round bracket slot is etched on the ground. The 1 × 4 phased arrays are used at the top edge and bottom edge of mobile PCB with high gain. The simulation results show that the antenna has four ultra-wide bands: 25.8–29.7, 40.6–44.6, 49.2–53.1, and 62.2–74 GHz with a maximum gain of 16.5 dBi at 51 GHz. The phased array antenna is capable to steer its main beam within ±30° at the 26, 28, and 43 GHz, using appropriate phase shifts of each antenna element. The proposed millimeter wave antenna is particularly suitable for cellular infrastructures and can be a candidate for emerging 5G mobile applications. The availability of an additional 11.8 GHz (62.2–74 GHz) of contiguous unlicensed spectrum will allow the launching of new exciting wireless services.

This paper deals with a near-field to far-field transformation able to predict the radiation of UHF antennas located over a lossy ground. From in-situ near-field measurements, an equivalent set of dipole sources is obtained as a model of the characterized antenna. The paper details the main steps of the transformation and describes the specific experimental set-up designed for the application. Simple directional antennas (monopoles array) as well as more complex omnidirectional antennas (like a biconical antenna as a scaled-down model of a HF antenna) have been tested in realistic environments. This approach is very efficient for separating the contributions of the radiated waves: the sky wave and the surface wave.

This paper presents a novel assessment method that minimizes test-fixture-induced errors in non-coaxial power combiner measurement by extending the port reduction method. This method involves terminating certain ports to acquire the scattering matrix of an N-port network from the scattering matrix measured at a reduced port order. The entire DUT scattering matrix is obtained from multiple scanning measurements, which are taken from partial coaxial accessible ports, based on a set of configurable terminating states. This advantage is leveraged to exclude a major portion of coaxial launch structures that would otherwise be incorporated in the conventional multiport test fixture. An analogous concept here is applied to measure a waveguide traveling-wave power combiner. A sandwiched twin structure, containing a divider/combiner pair with certain auxiliary through-type components cushioned between them, is utilized to assess the combiner characteristics. A theoretical framework of the proposed method was established to test its potential precision. Thereafter, an in-situ implementation was conducted to test its practical application on a traveling-wave combined amplifier prototype operating at the Q-band (33–39 GHz).

In the area of electromagnetic metrology, binary coded excitation signals become more and more important and various binary coded sequences are available. The measurement approach is to assess the impulse response function of a device under test by correlating the response signal with the excitation signal. In order to achieve a high measurement reproducibility as well as a high dynamic range, the generated binary coded signals have to provide low-noise. In this contribution, a low-noise signal generator realized with a field programmable gate array is presented. The performance investigation of different kinds of binary coded excitation signals and different correlation concepts have been practically investigated. With a chip rate of 5 Gchip/s, the generator can be utilized for ultra-wideband applications. In order to allow for a low-noise and long-term stable signal generation, a new clock generator concept is presented and results of phase noise measurements are shown. Furthermore, an algorithm to fast and precisely shifting the time lag between two binary coded signals for correlating excitation and response signals with a hardware correlator is presented. Finally, the realized demonstrator system is tested using two commonly used types of binary coded sequences.

In this paper, the patch-type frequency selective surfaces (FSS) based on substrate-integrated waveguide (SIW) technology is proposed to improve the bandwidth (BW) and angular performance. The proposed FSS configuration overcomes the limitations of both conventional 2D and 3D FSS structures. A closely coupled cascaded mechanism is employed to combine two identical FSS elements separated by thin dielectric substrate results in incorporation of SIW technology; hence, named as 2.5D FSS. A derived equivalent circuit model is used to estimate the basic performance of proposed FSS–SIW elements, and the response of analytical expressions has been validated and final design is obtained using full-wave simulations. Two basic FSS elements viz. single square loop and a Jerusalem cross have been investigated to prove the enhancement in their BW and angular stability. The proposed technique evidently improves the BW and angular stability of FSS structures than in its established form. Besides, various important parameters that influence the performance characteristics of reported 2.5D FSSs are also studied. The important observations made on the thickness, as the thickness increases the bandstop FSS, can change to bandpass FSS. Finally, the proposed FSS structure has been fabricated and measured using free space measurement setup, to show the effectiveness of theoretical results. The measured results show good agreement with simulated results at normal and oblique incidence angle.

In this paper, the solution of the inverse scattering problem for determining the shape and location of perfectly conducting scatterers by making use of electromagnetic scattered fields is presented. Based on the boundary condition and the measured scattered field, a set of nonlinear integral equations is derived and the imaging problem is reformulated into an optimization one. Then, two evolutionary algorithms are used to solve the inverse scattering problem. To further clarify, our contribution is to test two well-known algorithms in the literature to the problem of microwave imaging. The hybrid approaches combine the standard particle swarm optimization (PSO) with the ideas of the simulated annealing and extremal optimization algorithms, respectively. Both of them are shown to be more efficient than original PSO technique. Reconstruction results by using the two presented schemes are compared with exact shapes of some conducting cylinders; and good agreements with the original shapes are observed.

Design and development of 2 kW, 3 dB tandem hybrid coupler for the frequency range of 155–225 MHz has been presented in this paper. The developed 3 dB coupler is to be used in a prototype of Ion Cyclotron Resonance Frequency (ICRF) system of Tokamak, which has been developed to test the resilience of ICRF network during continuously variable RF load excursions. The 3 dB coupler divides the RF power between two antennae of the prototype and protects the RF source by coupling of reflected power to the isolated port. The developed coupler shows excellent coupling flatness of −3 ± 0.3 dB over 38% of fractional bandwidth and also provides voltage standing wave ratio (VSWR) <1.3, isolation better than 32 dB and return loss better than 25 dB in full band. The presented work establishes a technique which can be useful for the development of high-power hybrid coupler in the range of high frequency (HF), very high frequency (VHF) and ultra high frequency (UHF).

The measurement accuracy of low-frequency narrow-band antenna is heavily influenced by its environment, which is also difficult to remove the clutter with a time gating. This paper proposes a method to improve the measurement accuracy of low-frequency narrow-band antenna using signal processing technique. The method is to predict the unknown value out of received original signal with an auto-regressive model (AR model) based on modern spectral estimation theory, and the parameters in AR model are calculated by maximum entropy spectral estimation algorithm. Thus, a wideband signal compared with the original band is obtained, and then the time-domain resolution is enhanced. The time gating is more exactly to separate the antenna radiation signal from multipath signals. The simulation and experimental results show that about 50% extended data for each ends of original band can be obtained after spectral extrapolation, and the time-domain resolution after extrapolation is twice than the original narrow-band signal, and the influence of measurement environment can be eliminated effectively. The method can be used to improve accuracy in actual antenna measurement.

In this paper, we present a novel dual-band wearable compact flexible antenna for body-centric wireless communications (BCWCs). The design is based on a modified planar dipole with parasitic elements, meandered lines, and a rectangular reflector embedded into a hydrophobic rubber-textile multilayer substrate in order to get both good antenna performance and mechanical properties. The antenna's structure is analyzed and optimized in free space (FS), on a numerical and an experimental homogeneous flat phantom. The overall dimensions of the antenna are 50 mm × 40 mm × 4.6 mm and a prototype mass of 11 g, which makes it suitable for practical applications in BCWCs. The built prototype resonated at 2.47 GHz with a |S11|−26.90 dB and at 5.42 GHz with a |S11|−24.60 dB in the FS. The measured bandwidths are 500 MHz (2.2–2.7 GHz) and 1000 MHz (4.65–5.75 GHz) at lower and higher bands, respectively. The antenna exhibits a measured maximum gain of 1.17 dBi at 2.66 GHz and a radiation efficiency of 28.44% in FS. The 10 g average maximum specific absorption rate is 0.165 W/kg at 2.70 GHz and 0.520 W/kg at 5.24 GHz when the antenna is placed on the numerical phantom at net input power 0.1 W.

Design and fabrication of a microstrip feedline-based Vivaldi antenna in the frequency range of 6.0–8.0 GHz have been presented. The Vivaldi antenna is a planar antenna, fabricated at the microstrip feedline by having an exponentially tapered slot profile on it. An optimized computer-aided design has been developed and simulated for the desired radiation parameters like voltage standing wave ratio, bandwidth, directionality, beam-width, etc. The optimized design has been fabricated and tested. Wherever the results are not found as desired; problem has been comprehensively investigated and analyzed. This is found associated with a discontinuity at feed line, fabrication tolerance constraints and parasitic capacitance at the edges or the bent of the microstrip feedline which introduce the parasitic reactance in antenna design. Here, the presented work explores a generalized theoretical procedure for the compensation of associated problem by incorporating the reactive patch on the feedline. The developed theory is applied in fabrication and tested for the desired results.

The next generation of wireless networks (5G) employs directional transmission at millimeter wave (mmW) frequencies to provide higher bandwidth and faster data rates. This is achieved by applying antenna arrays with proper beam steering capabilities. Rotman lens has long been used as a lens-based beamformer in electronically scanned arrays and its efficient design is important in the overall performance of the array. Minimizing the phase error on the aperture of the antenna array is an important design criterion in the lens. In this paper, a 7 × 8 wideband Rotman lens is designed. Particle swarm optimization is applied to minimize the path length error and thereby the phase error. The optimized lens operates from 25 to 31 GHz, which covers the frequency bands proposed by the Federal Communications Commission for 5G communications. The proposed optimized lens shows a maximum phase error of <0.1°. The proposed Rotman lens is a good candidate to be integrated with wideband microstrip patch antenna arrays that are suitable for 5G mmW applications.

A microwave design for an industrial scale applicator of a continuous microwave assisted depolymerization of polyethylene terephthalate (PET) has been developed. The cavity is designed for use in combination with an Archimedean screw pump to transport the reaction material, surrounded by a cylindrical pipe with a diameter of 250 mm and a length of 250 mm at the 2.45 GHz ISM band. The proposed design is modular and can be easily expanded for the heating of longer reactor tubes. Simulation results show that a homogeneous heating of the process material along the screw axis can be achieved by using a novel cavity design which is based on the TE1,0,x– rectangular waveguide cavity mode. The achieved design provides high energy efficiency with a reflected power of less than 10%. It is robust against changes in the permittivity of the reactants. The electromagnetic design is based on the dielectric properties of the solvolytic reaction mixture measured in the relevant temperature range. It is verified over the full range of the expected permittivities.

A simple closed-form analytical formula is proposed to compute the probe reactance of an equilateral triangular patch antenna. The variation of the probe reactance with the variation of antenna dimension, substrate electrical parameters, and probe location is examined thoroughly. The computed values employing the present model show excellent agreement with experimental and simulation results.