Field experiments were conducted in 2006 and 2007 to evaluate the herbicidal activity of phenyl isothiocyanate (ITC) on yellow nutsedge, Palmer amaranth, and large crabgrass in tomato grown on two polyethylene-mulched types. Treatments included two mulch types (low density polyethylene [LDPE] mulch and virtually impermeable film [VIF] mulch) and phenyl ITC at 0, 15, 75, 150, 750, and 1,500 kg ha−1. A standard rate of methyl bromide/chloropicrin (67 : 33%) at 390 kg ha−1 under LDPE mulch was included for comparison. Regardless of mulch type, phenyl ITC at 1,452 (±133) and 1,719 (±426) kg ha−1 was required for broad-spectrum weed control equivalent to methyl bromide in 2006 and 2007, respectively. Tomato injury was ≥ 44% at the highest phenyl ITC rate of 1,500 kg ha−1 at 2 wk after transplanting (WATP) both years, irrespective of mulch type. Greater crop injury was observed from 750 kg ha−1 of phenyl ITC in 2006 (≥ 27%) than in 2007 (≤ 10%). The greater injury in 2006 was attributed to a higher phenyl ITC concentration because holes in the plastic mulch for transplanting were punched at the time of transplanting in 2006; whereas, in 2007 holes were punched 2 d before transplanting, allowing 2 d of aeration before transplanting. Tomato marketable yield at all rates of phenyl ITC was lower than with methyl bromide in 2006. However, in 2007, marketable yield in plots treated with phenyl ITC at 750 kg ha−1 was equivalent to methyl bromide. Overall, VIF mulch was no more effective than LDPE mulch at increasing weed control or improving the marketable yield of tomato either year.

Giant reed has been proposed as a bioenergy crop in the sugarcane production region of south Florida, where it has a high invasive potential. In an effort to limit future invasion of giant reed escapes in sugarcane, currently labeled sugarcane herbicides asulam and trifloxysulfuron were evaluated for its management. Greenhouse and field dose–response studies were conducted at the Everglades Research and Education Center in Belle Glade, FL, between 2010 and 2011. Herbicides were applied at rates ranging from 0.46 to 7.4 kg ha−1 asulam and 2 to 32 g ha−1 trifloxysulfuron, which represent 0.125× to 2× sugarcane labeled use rates, respectively. In the greenhouse, asulam and trifloxysulfuron reduced giant reed relative shoot dry weight by a maximum of 50% at 21 d after treatment (DAT). The probability of giant reed resprouting 35 d following herbicide treatment was greater for trifloxysulfuron when compared with asulam. In the field, it was predicted that a maximum of 69 and 55% giant reed control occurred with application of asulam and trifloxysulfuron, respectively, at 14 DAT. Relative shoot dry weight of giant reed treated with asulam and trifloxysulfuron was reduced by a maximum of 43% at 42 DAT. Application of asulam and trifloxysulfuron did not provide complete control of giant reed at twice the labeled sugarcane use rate, indicating that control of established giant reed in sugarcane with currently available herbicides would not be an option.

Methyl bromide has been widely used for weed control in polyethylene-mulched tomato production. With the phaseout of methyl bromide in the United States, an effective alternative is needed. Field experiments were conducted in 2007 and 2009 to determine if allyl isothiocyanate (ITC) would provide substantive weed control in tomato along with crop tolerance under low-density polyethylene (LDPE) and virtually impermeable film (VIF) mulch. Treatment factors included two mulch types (LDPE and VIF) and six rates of allyl ITC (0, 15, 75, 150, 750, 1,500 kg ha−1). A standard treatment of methyl bromide : chloropicrin (67 : 33%) at 390 kg ha−1 under LDPE mulch was also established. Allyl ITC was broadcast applied and incorporated in soil before forming raised beds and laying plastic mulch. Tomatoes were transplanted 3 wk after applying allyl ITC or methyl bromide treatments. Tomato injury was ≤ 8% in all treatments at 2 wk after transplanting (WATP). Allyl ITC at 913 (± 191) kg ha−1 was required to control yellow nutsedge, Palmer amaranth, and large crabgrass equivalent to methyl bromide at 6 WATP and maintain marketable tomato yield equivalent to methyl bromide treatment. VIF mulch was not effective in increasing weed control or improving the marketable yield of tomato over LDPE mulch. This research demonstrates that allyl ITC under an LDPE mulch can have a practical application for weed control in polyethylene-mulched tomato in the absence of methyl bromide.

Greenhouse and field studies were conducted to determine the effect of halosulfuron, imazosulfuron, and trifloxysulfuron applied through drip irrigation on yellow nutsedge. In greenhouse studies, yellow nutsedge control by halosulfuron, imazosulfuron, and trifloxysulfuron was greater (69 to 91%) than the nontreated control (0%). Yellow nutsedge treated with halosulfuron POST had a lower photosynthetic rate (0.6 to 22.6 µmol m−2 s−1) at 4, 7, and 14 d after treatment than the nontreated control (3.3 to 26.2 µmol m−2 s−1). Yellow nutsedge treated with trifloxysulfuron had lower photosynthetic rate and stomatal conductance than the nontreated plants. In field studies at Clinton, NC, yellow nutsedge density increased from treatment (day 0) to 56 d after treatment in all treatments. Increase in yellow nutsedge density was 72 and 95% in drip-applied halosulfuron and imazosulfuron treatments compared with yellow nutsedge density increases of 876% for the same period in the nontreated plots. Yellow nutsedge density increased 69 and 57% at Clinton and Kinston, NC, respectively, in the drip-applied 15 g ha−1 trifloxysulfuron treatment compared with 876% in the nontreated control. In field studies at Clinton and Kinston, NC, suppression of yellow nutsedge emergence in POST and drip-applied herbicide treatments was similar. Emergence of yellow nutsedge was similar in the imazosulfuron POST and the nontreated yellow nutsedge. Based on these studies, drip-applied herbicides may be beneficial as a part of a yellow nutsedge control program, but additional measures, such as a POST herbicide, would be needed for effective control. Drip-applied herbicides may give growers an option for herbicide application after drip irrigation tape and polyethylene mulch have been installed in the current vegetable crops. This application method would also allow herbicide treatment under plastic mulch used for multicropping systems.

Herbicides used to control many forb species in pastures may injure desirable native grass species. Buffalograss, a major component of shortgrass rangeland, often is injured by some growth regulator herbicides, such as 2,4-D and dicamba. Aminocyclopyrachlor (formerly known as DPX-MAT28 and herein termed ACPCR), a new synthetic auxin herbicide chemistry for control of broadleaf weeds, was investigated for injury to buffalograss and control of forbs in shortgrass prairie at varying rates of application. In the season of application, ACPCR at rates of 140 g ai ha−1 or less caused buffalograss injury that was either negligible or short-lived, and visual estimates of grass injury were 8% or less at the end of the growing season. At ACPCR rates of 280 g ha−1, more injury was evident at 3 wk after treatment (WAT) than at the end of the season if adequate precipitation was available for new leaf growth. When precipitation was lacking, evidence of injury persisted through to the end of the season when treated at the greatest rate of ACPCR. Buffalograss injury was mainly in the form of browned leaf tips, but total buffalograss dry matter yield was not different between any treatments in either year. The year after treatment, no buffalograss injury was evident from any of the herbicide rates. Final forb control was 97% or greater each year for ACPCR at the 140 and 280 g ha−1 rates. In this experiment, rates as low as ACPCR at 140 g ha−1 provided excellent forb control and maintained buffalograss productivity.

Morningglories are summer annual or perennial dicots, and are troublesome weeds in sugarcane cultivated in northern India. If not controlled, they may compete with sugarcane, interfere in the harvest operation, and reduce yields. Managing morningglories in sugarcane continues to be a serious challenge for sugarcane growers. Field experiments were conducted during the 3-yr period from 2007 to 2009 to evaluate herbicides applied PRE and POST for control of morningglories in sugarcane. The herbicides applied PRE included diuron, metribuzin, and atrazine at 1.6, 1.4, and 1.0 kg ai ha−1, respectively, applied alone or followed by 2,4-D amine salt (0.58 or 1.16 kg ae ha−1) or 2,4-D sodium salt (0.8 or 1.6 kg ae ha−1) applied POST. Herbicides applied PRE controlled morningglories ≤ 87% at 15 d after treatment (DAT); however, control reduced to ≤ 56% at 90 DAT. Control improved when herbicides applied PRE were followed by POST application of 2,4-D amine or sodium salt. For example, diuron applied PRE followed by 2,4-D amine salt applied POST at any rate provided 100% control of morningglories at 15 and 30 DAT. At 90 d after POST application, control ranged from 68 to 82% with the PRE followed by POST herbicides, compared to 0% control when metribuzin or atrazine were applied PRE alone. The density and biomass of morningglories was also reduced to zero in treatments that included 2,4-D amine salt. The number of millable canes, cane height, and single cane weight was superior in PRE followed by POST herbicide treatments compared to herbicides applied PRE alone. Maximum cane yield was recorded for the treatments that included 2,4-D amine or sodium salt compared to only PRE treatments, and it was usually comparable with the nontreated weed-free control. It is concluded that a combination of PRE and POST herbicides were effective for control of morningglories; however, more research is required to evaluate other herbicides and their tank mix partners for control of morningglories in sugarcane.

We tested the effects of seeding date and weed control during switchgrass establishment in a field experiment that was conducted in central Pennsylvania in 2007 and repeated in 2008. Switchgrass was no-till seeded in early May, late May, and mid-June, and three postemergence weed management treatments were evaluated, including Mow (only a single mowing), Broadleaf (2,4-D + dicamba), and Broad Spectrum (2,4-D + dicamba + atrazine + quinclorac). Switchgrass density increased at later seeding dates, except in 2008, when the middle seeding date had the lowest density. In both years, weed biomass in late summer was lowest in the last seeding date of the Broad Spectrum treatment. In contrast, switchgrass biomass in late summer was greatest in the first seeding date of the Broad Spectrum treatment in both years. In the year after establishment (production year), plots were split to test the effects of supplemental weed control, composed of metsulfuron + 2,4-D applied in May, on total aboveground yield. Supplemental control in the production year increased total aboveground yield in the Mow treatment only, indicating that effective weed control during the establishment year might reduce the need for weed control in the following year. Although maximum aboveground yield was achieved when switchgrass was seeded in May and herbicides were used, results from our experiment suggest that seeding switchgrass at a relatively high seeding rate in June in our study region and mowing annual weeds to reduce competition and prevent seed production could be an effective strategy if minimizing herbicide use is a priority.

Flucarbazone controls certain grassy weeds in wheat and may have potential for controlling perennial ryegrass in tall fescue turf. The objective of these experiments was to investigate perennial ryegrass and tall fescue tolerance to flucarbazone at two application timings. In field experiments, flucarbazone applications in May were more injurious to both species than in February and March. Single applications of flucarbazone from 30 to 60 g ai ha−1 in May injured both species 35 to 50% and sequential treatments increased injury approximately twofold. Two applications of flucarbazone at 60 g ha−1 in May injured both grasses > 90%, similar to sequential applications of trifloxysulfuron at 29 g ai ha−1. In growth chamber experiments, injury from flucarbazone on both grasses increased as temperature increased from 10 to 30 C. Flucarbazone reduced total shoot biomass of both grasses at all temperatures after 4 wk. Overall, perennial ryegrass and tall fescue are tolerant to flucarbazone at moderate temperatures (10 to 20 C). However, injury increased substantially under warmer conditions (30 C), suggesting flucarbazone could control perennial ryegrass and tall fescue during late spring and early summer.

An experiment was conducted on a specially designed hard surface to study the impact of time interval between flaming treatments on the regrowth and flower production of two grass weeds. The goal of this experiment was to optimize the control of annual bluegrass and perennial ryegrass, both species that are very difficult to control without herbicides. Aboveground biomass from 72 plants per treatment was harvested and dry weights were recorded at regular intervals to investigate how the plants responded to flaming. Regrowth of the grasses was measured by harvesting aboveground biomass 2 wk after the second flaming treatments that were implemented at different time intervals. Flaming treatments decreased plant biomass of both species and also the ratio of flowering annual bluegrass plants. However, few plants were killed. The first flaming treatment affected aboveground biomass more than the second flaming treatment. A treatment interval of 7 d provided the greatest reduction in regrowth of perennial ryegrass, whereas the effect of treatment interval varied between the first and second repetitions of this experiment for annual bluegrass. In general, short treatment intervals (3 d) should be avoided, as they did not increase the reduction of aboveground biomass compared with the 7-d treatment interval. Knowledge on the regrowth of grass weeds after flaming treatments provided by this study can help improve recommendations given to road keepers and park managers for management on these weeds.

Field studies were conducted to determine the response of sublethal glyphosate and dicamba doses to processing tomato flowering loss and marketable yield. Dose–response studies for both herbicides were conducted on four commercial processing tomato lines (two different lines within each study) and plants were sprayed at either the vegetative stage or the early bloom stage. Both glyphosate and dicamba caused higher yield losses when sprayed at the early bloom stage. A 25% yield loss was observed with 8.5 and 7.5 g ae ha−1 for glyphosate and dicamba, respectively, at the early bloom stage and 43.9 and 11.9 g ae ha−1 for glyphosate and dicamba, respectively, at the early vegetative stage. Overall, these tomato cultivars were more sensitive to dicamba than to glyphosate. We conclude that glyphosate and dicamba drift could have serious implications on tomato yields especially if the drift occurs during flowering.

Studies were conducted in 2007 and 2008 to evaluate herbicides having both PRE and POST activity for selective weed control in bald cypress plantings. Five herbicides were applied at two or three rates at two different timings. The first timing was to dormant seedlings without foliage and prior to weed emergence (i.e., PRE). The second timing was to foliated seedlings with established weed seedlings present (i.e., POST). Herbicide treatments included aminopyralid at 70 and 120 g ae ha−1, hexazinone at 420 and 560 g ai ha−1, imazapyr at 140 and 210 g ae ha−1, sulfometuron methyl at 110, 160, and 210 g ai ha−1, and flumioxazin at 290 and 430 g ai ha−1. Herbicide rate had little effect on vegetation control. PRE-applied sulfometuron methyl was most effective, providing nearly complete control of graminoids and broadleaves at 60 d after treatment (DAT). POST-applied treatments were generally less effective, though in the 2008 study imazapyr and sulfometuron methyl resulted in approximately 60% bare ground at 60 DAT. Growth of bald cypress seedlings was enhanced by both PRE- and POST-applied sulfometuron methyl, flumioxazin, or hexazinone and by PRE imazapyr. The best bald cypress growth response followed POST-applied sulfometuron methyl at 210 g ha−1, which resulted in 63 cm3 mean volume index, more than fivefold greater than the nontreated check. Aminopyralid caused severe and lasting seedling injury. POST-applied imazapyr resulted in fasciculation and no growth benefit, despite providing the most efficacious weed control among POST treatments. Survival and growth of bald cypress can be greatly enhanced with a single selective herbicide treatment using sulfometuron methyl, flumioxazin, or hexazinone applied before or following foliation in the spring.

Flumioxazin is used in nursery production and landscape maintenance industries. In these situations, weed control provided by flumioxazin often lasts longer than that reported in soil. Our objective was to quantify flumioxazin longevity under conditions found in nursery production. Pots were filled with 6 : 1 (v/v) pine bark : sand mixture. This nonsoil media is typical of what is used for nursery crop production. Pots were treated with flumioxazin at either 0.28 or 0.42 kg ai ha−1, and subsequently sown with either hairy bittercress (two winter experiments) or spotted spurge (two summer experiments) at weekly intervals. Weed seed germination, emergence, and seedling establishment in the treated pots was compared with nontreated control and used as a proxy for herbicide activity. Flumioxazin provided approximately 7 wk of complete (100%) hairy bittercress control regardless of rate. However, a rate effect was evident in only one of the two experiments conducted with hairy bittercress. In both experiments with hairy bittercress, marginal and highly variable activity was still evident at 18 wk after treatment. Flumioxazin at 0.28 and 0.42 kg ha−1 provided 2- and 4-wk complete spotted spurge control, respectively. No spotted spurge control was evident after about 8 wk. Subjecting this less-variable data to nonlinear regression revealed that the time required for 50% reduction in flumioxazin activity was approximately 5.5 and 6.6 wk for the two rates, respectively. A column leaching study revealed that flumioxazin activity remained localized near the surface (0 to 4 cm). Therefore the dissipation observed was likely the result of in situ degradation and not displacement. The high organic matter content of the nonsoil media contributes to the observed persistence of flumioxazin activity.

Dermatitis from poison ivy is a significant health problem. Considerable effort is devoted to the control of this invasive and virulent weed in urban areas. Glyphosate, triclopyr, 2,4-D, a 1 : 1 mixture of glyphosate and 2,4-D, and a 9 : 1 mixture of glyphosate and triclopyr were evaluated for poison ivy control. Each of these three herbicides and two mixtures were applied at nine or ten rates, which ranged in phytotoxicity from none to death. Poison ivy plants had been propagated and container-grown. Percent control, as determined from plant fresh weight reduction, was determined at 1 and 4 mo after treatment (MAT). Data were subjected to ANOVA followed by nonlinear regression. Rates required for 95% control at 1 and 4 MAT and the associated costs were determined for each of the three herbicides and two mixtures. Acceptable control (i.e., ≥ 95%) at 1 and 4 MAT could be obtained at a much lower cost with either triclopyr or 2,4-D than with either glyphosate alone or with the two glyphosate-containing mixtures. Nonlinear regression also was used to evaluate whether the two mixtures were interactive (i.e., synergistic or antagonistic) or not (i.e., additive). Glyphosate plus triclopyr was synergistic for control at both 1 and 4 MAT. Glyphosate plus 2,4-D was synergistic for control at 4 MAT only. However, for both mixtures, synergism was only evident at rates that controlled poison ivy ≤ 80%. Both mixtures were noninteractive at rates required for acceptable control.

Saflufenacil is a new protoporphyrinogen oxidase–inhibiting herbicide registered for use before establishment of field corn and soybean. Generally, peanut plants are tolerant to other herbicides in this class, and no reports document the utility of saflufenacil for in-season weed control. Experiments were conducted to determine whether saflufenacil applied at 12, 25, and 50 g ha−1 could effectively control Benghal dayflower and Palmer amaranth. It was observed that saflufenacil, applied either PRE or POST, was ineffective for Benghal dayflower. The maximum control at 28 d after treatment (DAT) was 79% when 50 g ha−1 was applied to 5- to 10-cm plants. Control of Palmer amaranth from PRE applications was less effective than flumioxazin at 28 DAT. However, POST applications provided > 87% control at 28 DAT when applied to plants 5 to 10 cm in height. For plants 10 to 15 cm in height, > 90% Palmer amaranth control was only achieved by the 50 g ha−1 application rate. For plants 15 to 20 cm in height, no POST application provided > 70% control. Peanut response, in a weed-free environment, to saflufenacil rate and application timing were also evaluated. Peanut stunting ranged from 0 to 36%, relative to application timing. Applications made at 0 d after emergence (DAE) were least injurious, whereas those made at 15 DAE were most injurious. Application of 50 g ha−1 provided the greatest amount of stunting and foliar injury. However, stunting and saflufenacil application rate did not correspond to yield reduction. Saflufenacil application timing did influence peanut yield. Applications made between 0 and 30 DAE did not result in yield loss, whereas applications made at 45 and 60 DAE resulted in a 5 and 19% reduction, respectively. Though saflufenacil has many positive characteristics, higher application rates are required for optimum weed control. However, these higher use rates also resulted in unacceptable levels of injury.

Alligatorweed is subject to an eradication program in Victoria, Australia. In aquatic situations, the herbicides glyphosate and metsulfuron are used. Alligatorweed has been shown to break up soon after the application of these herbicides, resulting in the production of many stem fragments that are viable and capable of downstream colonization, compromising the effectiveness of the eradication program. This paper reports on an experiment to investigate the usefulness of commercially available plant growth regulators (PGRs) in reducing the number of viable propagules produced post-herbicide application. Three herbicide treatments (no herbicide, glyphosate, and metsulfuron) and four PGR treatments (no PGR, aviglycine [AVG], naphthalene acetic acid [NAA], and 2,4-D) were investigated in a factorial experiment. Chemicals were applied to alligatorweed growing in separate aquaria, the resulting stem fragments were collected and counted, and a subset was tested for viability. There was no evidence of PGRs having any effect on the total number of viable stem fragments produced. However, AVG reduced the total number of fragments produced. PGRs in combination with herbicide treatment had an antagonistic effect on the efficacy of the herbicides. PGRs increased belowground biomass of alligatorweed, as well as the number of apical growing tips present. Results indicate that although PGRs, particularly AVG, may be of benefit in reducing the number of alligatorweed propagules produced post-herbicide application, at the application rates tested here there would be no benefit from incorporating them into herbicide control programs for alligatorweed.

Greenhouse and field studies were conducted to determine tolerance of tomato to halosulfuron, imazosulfuron, and trifloxysulfuron herbicides applied through drip irrigation. In greenhouse studies, PRE- and POST-applied trifloxysulfuron caused greater tomato injury (14 and 54% injury, respectively) than PRE- and POST-applied halosulfuron (5 and 26% injury, respectively) or imazosulfuron (5 and 23% injury, respectively). All herbicide treatments in the greenhouse studies caused greater injury to tomato than the nontreated. Greater tomato injury was observed in the greenhouse from herbicides applied POST than when soil applied. Tomato injury from POST-applied halosulfuron, imazosulfuron, or trifloxysulfuron followed a linear relationship, with tomato injury increasing with increasing herbicide rate. Tomato photosynthetic rate did not differ among the herbicide treatments (32.7 to 55.0 μmol m−2 s−1) and the nontreated (38.0 to 55.0 μmol m−2 s−1). At 5 to 16 days after treatment (DAT), tomato treated with imazosulfuron POST (0.26 to 0.46 cm s−1) or trifloxysulfuron POST (0.27 to 0.51 cm s−1) had lower stomatal conductance compared to the stomatal conductance of the nontreated tomato (0.65 to 0.76 cm s−1). Chlorophyll content did not differ among treatments at 0 to 6 DAT. At 7 to 12 DAT, tomato treated with imazosulfuron POST (34.0 to 40.1 SPAD) and trifloxysulfuron POST (35.0 to 41.6 SPAD) had lower chlorophyll content compared to the nontreated (39.1 to 48.1 SPAD). In 2008 and 2009 field studies, no tomato injury was observed. Herbicide, herbicide application method, and herbicide rate had no effect on tomato height (73 to 77 cm 14 DAT, 79 to 84 cm 21 DAT) and total fruit yield (62,722 to 80,328 kg ha−1).

Studies were conducted in 2008 and 2009 to determine the effect of S-metolachlor rate and application time on sweetpotato cultivar injury and storage root shape under conditions of excessive moisture at the time of application. S-metolachlor at 1.1, 2.2, or 3.4 kg ai ha−1 was applied immediately after transplanting or 2 wk after transplanting (WATP) to ‘Beauregard’, ‘Covington’, ‘DM02-180’, ‘Hatteras’, and ‘Murasaki-29’ sweetpotato. One and three d after S-metolachlor application plots received 1.9 cm rainfall or irrigation. S-metolachlor applied immediately after transplanting resulted in increased sweetpotato stunting 4 and 12 WATP, decreased no. 1 and marketable sweetpotato yields, and decreased storage root length to width ratio compared with the nontreated check. Sweetpotato stunting, no. 1 and marketable yields, and storage root length to width ratio in treatments receiving S-metolachlor 2 WATP were similar to the nontreated check. In 2008, Covington and Hattaras stunting 12 WATP was greater at 2.2 and 3.4 kg ha−1 (11 to 16%) than 1.1 kg ha−1 (1 to 2%). In 2009, S-metolachlor at 3.4 kg ha−1 was more injurious 4 WATP than 2.2 kg ha−1 and 1.1 kg ha−1. While cultivar by treatment interactions did exist, injury, yield, and storage root length to width ratio trends were similar among all cultivars used in this study.

Elephantgrass has been proposed as a potential feedstock for biofuel production in south Florida. To limit future invasion of escapes in sugarcane and vegetables, the response of newly established elephantgrass to glyphosate, clethodim, sethoxydim, asulam, and trifloxysulfuron was determined using dose–response curves. Log-logistic models were used to determine the herbicide dose required to produce 90% growth reduction (GR90). The GR90 values for shoot biomass at 21 d after treatment (DAT) were 477 g ae ha−1 of glyphosate, 262 g ai ha−1 of clethodim, 381 g ai ha−1 of sethoxydim, 12 kg ai ha−1 of asulam, and 94 g ai ha−1 of trifloxysulfuron. The GR90 values for root biomass at 35 DAT were 570 g ae ha−1 of glyphosate, 257 g ai ha−1 of clethodim, 432 g ai ha−1 of sethoxydim, 17 kg ai ha−1 of asulam, and 183 g ai ha−1 of trifloxysulfuron. Elephantgrass was predicted to exhibit 97, 98, 75, 1, and 5% mortality after application of glyphosate, clethodim, sethoxydim, asulam, and trifloxysulfuron, respectively, at the label use rates 35 DAT. Results suggest that glyphosate and clethodim will provide control of newly established elephantgrass at label use rates for spot treatments and in vegetables, respectively. Rates higher than the label use rate of sethoxydim will be required to provide acceptable control of newly established elephantgrass in vegetables. However, newly established elephantgrass was not controlled by asulam and trifloxysulfuron at label use rates, implying that control of escapes will be difficult in sugarcane.

Greenhouse studies were conducted to evaluate the influence of selected adjuvants on glyphosate efficacy on yellow nutsedge and tuber production. Glyphosate was applied at 0, 0.25, 0.43, 0.87, 1.26 (1× rate), and 1.74 kg ae ha−1 at 31 d after yellow nutsedge was planted. Each rate was mixed with one of the following adjuvants: ammonium sulfate (AMS), AMS plus nonionic surfactant (NIS), or AMS plus an experimental adjuvant (W-7995) plus NIS. Plants were evaluated for injury and for the number and size of tubers produced. Dose–response curves based on log-logistic models were used to determine the effective glyphosate rate plus adjuvant that provided both 90% effective dose (ED90) for yellow nutsedge injury and reduced tuber production. Addition of NIS to glyphosate plus AMS resulted in the greatest yellow nutsedge injury at 28 d after treatment (DAT). Addition of the experimental adjuvant plus NIS resulted in injury similar to NIS alone. The ED90 for injury at 28 DAT was 2.12 kg ha−1 with glyphosate plus AMS and NIS compared with 2.18 kg ha−1 for W-7995 plus NIS and 3.06 kg ha−1 with AMS alone. The ED90 rates with different adjuvants represent 168%, 173%, and 243% of the highest glyphosate rate (1.26 kg ha−1) labeled for application on many glyphosate-resistant crops. However, the estimated ED90 to reduce small, medium, large, and total tubers were 1.60, 1.50, 1.63, and 1.66 kg ha−1, respectively. Increases in labeled rates of glyphosate may be required to reduce yellow nutsedge tuber production in field conditions. Use of lower glyphosate rates should be discouraged because it may increase tuber production and exacerbate yellow nutsedge expansion in infested fields.

Summer annual grasses such as goosegrass and smooth crabgrass can hinder seeded zoysiagrass establishment. The herbicide fluazifop controls various grassy weed species but can injure mature and seedling zoysiagrass. Research has indicated that fluazifop applications can be safened on mature zoysiagrass cultivars with the addition of triclopyr. Based on these observations, research was conducted to evaluate weed control and tolerance of seeded ‘Zenith’ zoysiagrass to fluazifop (0.11 or 0.21 kg ai ha−1), triclopyr (1.12 kg ae ha−1), or fluazifop plus triclopyr (0.11 or 0.21 kg ha−1 plus 1.12 kg ha−1) applied at seeding, 14, or 28 d after emergence (DAE). All herbicide treatments applied at seeding did not hinder zoysiagrass germination but did not reduce goosegrass populations. Fluazifop alone (0.11 and 0.21 kg ha−1) applied at 14 and 28 DAE injured zoysiagrass seedlings but was reduced with the addition of triclopyr. At the end of the growing season, the greatest zoysiagrass cover was achieved by applications of fluazifop alone (0.11 kg ha−1) applied at 14 DAE or fluazifop (0.11 or 0.21 kg ha−1) plus triclopyr applied at 14 or 28 DAE. Fluazifop (0.11 or 0.21 kg ha−1) applied alone or tank-mixed with triclopyr controlled goosegrass > 70% when applied 14 and 28 DAE. Based on these data, applications of fluazifop tank-mixed with triclopyr can successfully control goosegrass without injuring Zenith zoysiagrass seedlings.