In this article, an angle-independent wideband metamaterial microwave absorber (MMA) for C (4–8 GHz) and X (8–12 GHz) band frequency is presented. The unit cell of the proposed MMA consists of outer and inner structure associated with lumped resistors. The outer structure consists of rectangular split-ring resonator, whereas the inner structure consists of circular split-ring resonator. The structure is made up of three layers, in which top and bottom layers are made up of copper acting as a conducting material. The middle layer is made up of FR-4 acting as a dielectric substrate. The resonating structure at the top is designed in such a way that wideband absorption is achieved in the range from 6.11 to 13.52 GHz. The wideband absorption within the range approaches almost unity having a bandwidth of 7.41 GHz. Three different peaks are considered in the range of interest having maximum absorption of 0.94, 0.94, and 0.99 at frequencies of 6.76, 11.15, and 13.07 GHz, respectively. The structure is analyzed with respect to the effective parameters, i.e., effective permittivity (${\varepsilon _{{\textrm{eff}}}}$) and effective permeability (${\mu _{{\textrm{eff}}}}$), to prove that the structure acts as a metamaterial. Electric field and current distribution are plotted at three different peaks to prove the mechanism of wideband absorption. Normal and oblique incidence are plotted to determine that the structure is behaving as an angle independent. The simulated structure is fabricated on FR-4 substrate and measured inside an anechoic chamber. Finally, to prove the novelty of the work, the proposed structure is compared with the already reported MMA. The proposed MMA finds practical applications in radar cross section reduction, terrestrial communication, keyless entry system, space communication, radar, and baby monitor.

A metasurface reflector-backed wideband planar antenna is designed for millimeter-wave (mmWave) applications. A simple meandering structure is used for radiation element design, while the back side consists of a partial ground plane and parasitic elements. The utilization of meander-shaped element led to small antenna dimensions. The partial ground plane is used to achieve wide bandwidth, while the parasitic elements are used to improve the impedance matching toward higher frequency bands. To achieve high gain and directional radiation characteristics, an array of metasurfaces is placed behind the radiating element. It is observed from the simulated results that the proposed antenna system offers 17.72 GHz of impedance bandwidth in the operating range of 22.28–40 GHz, while the measured impedance bandwidth is noted to be 15.8 GHz, ranging from 23 to 38.8 GHz. Furthermore, it is observed that a metasurface-based planar antenna tends to achieve a peak gain of ≈9 dBi in the band of interest.

A novel reconfigurable circular microstrip G-slotted antenna having a circularly defected ground structure (DGS) capable of switching its resonance frequency for several microwave applications is presented in this paper. Reconfigurability of the proposed G-slot antenna is obtained by incorporating three PIN diodes. One diode is embedded in the patch and two diodes are integrated into the DGS structure at appropriate places in the slot to achieve four different wireless applications such as aeronautical radio navigation (4.3 GHz with gain 3.6 dB), satellite communication (3.78 GHz with gain 3.7 dB), mobile communication (4.55 GHz with gain 4.0 dB), and WiMAX (3.35 GHz with gain 3.3 dB). These four bands are achieved depending on the different biasing conditions of the three PIN switches used. Antenna performance has been analyzed in ANSYS Electronics Desktop 2018.2 software. The equivalent circuit component of the switching element (PIN diode) has been considered and designed during the simulation. The creative structure lies in the way that it exhibits higher gain with compact size than the previously reported similar antenna. A prototype of the proposed patch antenna has been fabricated on a Roger substrate and its testing and measurement have been performed to demonstrate its desirable characteristics and features.

This paper investigates the electromagnetic scattering characteristics in arid zone and proposes methods for monitoring and improving ecological agriculture, vegetation landscape and desertification in arid zone, based on the modified small slope approximation (SSA) electromagnetic scattering model. The dielectric properties of dryland soils are studied in the paper, and the variation curves of soil dielectric constant with humidity and electromagnetic frequency are plotted. In order to reproduce the geomorphological features of the dryland areas, a two-dimensional geometric model of the ground environment is established using Monte Carlo methods combined with Gaussian spectral functions. An algorithm model based on the modified SSA is developed, and the algorithm was validated and analyzed to verify its reliability. In the simulations, the southeastern region of Ejina Banner, Inner Mongolia was taken as a typical arid region, and the simulation parameters are obtained from the actual measurement data of the region. The study finds that the electromagnetic scattering characteristics of the arid zone are influenced by soil water content, ground roughness and incident wave electromagnetic frequency, and there is regularity. The results of this paper can be effectively combined with remote sensing technology to contribute to many researches on soil moisture inversion and ecological condition of vegetation, which are important in many aspects such as irrigation control, ecological research, vorticity covariance, and climatology of slope stability.

The increasing demand for wireless communication has emphasized the need for multiband antennas. This study presents a novel design for a multiband antenna with reduced specific absorption rate (SAR), high gain, and improved front-to-back ratio (FBR) achieved through the integration with a 4 × 4 artificial magnetic conductor (AMC) surface. The proposed antenna covers a wide range of wireless frequency bands, including Industrial, Scientific, and Medical, Wireless Local Area Network, Worldwide Interoperability for Microwave Access, Wi-Fi 6E, and 7, with resonating frequencies at 2.4, 3.2, 5.5, 7.5, and 10 GHz. The AMC unit cell creates four zero-degree reflection phases with double negative properties at 2.5, 3.8, 5.5, and 7.5 GHz. The compact design measures 0.23λ0 × 0.296λ0 × 0.0128λ0 and placed 0.104λ0 above an AMC surface of size 0.512λ0 × 0.512λ0 × 0.1296λ0. This structure enhances the gain by up to 8.55dBi at 6.01 GHz. The proposed antenna has −10 dB impedance bandwidth for these corresponding frequencies viz 2.34–2.43 GHz (3.77%), 2.81–3.83 GHz (30.72%), 4.82–6.21 GHz (25.20%), 7–7.65 GHz (8.87%), and 8.06–10.31 GHz (24.5%). An overall average percentage reduction value of SAR taken at these frequencies has been found to be 96.11% with AMC structure. The antenna sample was successfully fabricated, and the experimental results have been found to match well with the simulation results. This integrated design offers a promising solution for wearable off-body communication devices.

A dual-band angular-stable transmissive linear to circular polarization converter based on metasurface is proposed and demonstrated in this work. The converter consists of three layers. The top and bottom layers are formed by an array of double split-ring layers. The unit cell of the central layer contains a square loop nesting a slant dipole. The split-rings create two resonances, enabling dual-band operation. The slant dipole and square loop are useful for improving the quality of circular polarization conversion. It is shown that the proposed polarization converter converts the incident linearly polarized wave into circularly polarized wave with opposite polarization modes over the frequency ranges of 8.77–10.58 and 17.59–19.88 GHz. The angular stability is up to 60° for 3 dB axial ratio. Moreover, the thickness of unit cell has a wavelength below 0.06 at the lower band. Compared with other designs in the literature, the structure bears merits of wideband response, high angular stability, and low-profile property within dual-band operational region. To validate the design, a sample prototype was designed, fabricated, and measured. The measured results are in good agreement with the simulated ones.

This paper proposes a passive filtering antenna for ultra-wideband (UWB) applications. The edge chamfering technique is adopted to construct the UWB antenna. The designed UWB antenna has a fractional bandwidth of 135%. A low-pass filter (LPF) is embedded on the feed line of the UWB antenna to convert it into a narrowband antenna that works at 2.45 GHz with 29.5% fractional bandwidth by removing the high-frequency components. The LPF is a transmission line with a stepped impedance configuration loaded with an H-shaped unit cell. The proposed filtering antenna is fabricated and tested. The measured results indicate the gain is >4.2 dBi and the radiation efficiency is >75%.

The presence of obstacles in the propagation path is a critical factor in air-to-ground (AG) communication. The behavior of wireless signal propagation depends on several variables, such as frequency, building height, elevation angle, and street design. This paper aims to compare the three established line of sight (LOS) probability model based on actual site data, including the building geometry in suburban environment. The comparison between these three models using the site data provide a guideline for selecting the LOS probability model based on the optimistic and pessimistic predictions. The shadowing loss was evaluated at frequencies 2 and 3.5 GHz with an elevation angle of 20° in two suburban locations at Universiti Tun Hussein Onn Malaysia. Three prediction models, ITU-R P.1410-5, Holis and Pechac, and Pang et al., available in the literature were used to identify and compare the line-of-sight probability. By focusing on the shadowing model in suburban area, the guideline for optimizing LOS communications or navigation in these challenging environments can be developed. The finding highlights the importance of considering building height in AG communication for network performance evaluation and design.

This manuscript presents a 50 Ω microstrip-fed quad-element high isolated ultra-wideband (UWB) multiple-input multiple-output (MIMO) antenna with band-notched characteristics. The overall area of the proposed structure is 0.33λo × 0.33λo mm2 (where λo depicts the free space wavelength corresponding to the lower cutoff frequency, i.e. 2.54 GHz), etched on an FR-4 substrate of thickness 0.8 mm. The top layer has four semicircular disc-shaped radiating elements that are identical and orthogonal to obtain better inter-element isolation and compactness. A reverse two-shaped slot is etched onto the radiating patches to attain a band-rejection capability. Moreover, a decoupling structure is also placed at the top layer to suppress the unwanted surface waves. The bottom layer consists of a ground plane, which is further modified with quasi-self complementary and meandered line slots. A rectangular slot is also etched below the feed line to better match the impedance near the lower cutoff frequencies. The simulated reflection coefficients (S11) of the proposed antenna are less than −10 dB over 2.54 to 10.74 GHz frequencies except at 3.37 to 4.15 GHz (WiMAX/C band), and the simulated inter-port isolation (S21) is greater than −15 dB over the entire UWB range of frequencies (3.1 to 10.6 GHz). Also, the measured S-parameter results well agreed with the simulated ones. Furthermore, the simulation study of the 20-element UWB-MIMO antenna is also investigated using the proposed quad-element structure.

In this article, the cylindrical conformation of a linearly polarized cavity-backed magnetoelectric (ME) antenna is studied. Starting from a planar ME antenna presenting a wide bandwidth due to a specific design of its feeding probe, the impact of conformation is shown; the coupling between the ME dipole and the cavity walls is demonstrated to be the key element to keep a wideband behavior. Conformal antennas offering the same impedance bandwidth as the planar antenna are presented operating at Global Navigation Satellite System frequencies (1.164–1.61 GHz). As a result of the conformation, the antenna size has to be reduced to maintain the coupling and a wideband behavior. A prototype conformed to a 44-mm radius cylinder was built using low-cost additive manufacturing. External dimensions of 62 × 62 × 35 mm3 (0.285 × 0.285 × 0.16λ03, where λ0 is the wavelength at 1.38 GHz) were obtained, showing a ground plane area reduction of 46% compared to the planar antenna with the same materials. The conformal antenna also exhibits very steady radiation properties with a gain of around 4.5 dBi and a very similar and stable 3 dB beamwidth around 113° in E- and H-planes. A relatively good agreement is found between measurements and simulation.

Future smart reconfigurable antennas (RAs) (Haupt R-L and Lanagan M (2013) Reconfigurable antennas. IEEE Antennas and Propagation Magazine 55, 49–61) will likely be fully multipurpose and controlled by software and equipped with machine learning skills that can discern and respond to alterations in the radio frequency environment. Cognitive radio utilizations will be accomplished using a new generation of antenna technology and communication protocols. The effective use of frequencies and the use of polarization diversity and radiation pattern reconfigurability to send data over existing congested frequencies will be major advantages for such applications. The usage of antennas that can be reconfigured in multiple-input multiple-output (MIMO) channels will enhance channel capacity while simultaneously improving channel efficiency and lowering costs (Christodoulou C-G, Tawk Y, Lane S-A and Erwin S-R (2012) Reconfigurable antennas for wireless and space applications. Proceedings of the IEEE 100, 2250–2261). There are a lot of antennas used both at the transmitter and at the receiver front end in a MIMO system. The benefit of employing such arrangements is that different types of information can be conveyed at a similar time, boosting the spectral efficiency of communication in a multipath situation. The coding rate, modulation level, and transmission signaling method of a MIMO system can all be changed in response to changing channel circumstances and user needs. In a MIMO context, polarization reconfigurable/frequency-reconfigurable/radiation pattern RA increase the degree of freedom and enhancing the system’s performance. The usage of such antennas greatly enhances capacity by enabling a choice of various polarization configurations and pattern diversity. Antenna arrays that can be reconfigured are also an appealing MIMO system solution that needs to retain robust communication channels, particularly in portable gadgets where the area is limited.

For future fifth-generation (5G) smartphones, a high-efficiency multiple-input/multiple-output (MIMO) antenna system capable of operating in Long Term Evolution (LTE) 42/43/46 is suggested. A pair of small microstrip-fed slot antenna and inverted F antenna is part of the single antenna design structure. They are positioned on the longer side of the FR-4 printed circuit board. In an effort to lessen the mutual coupling, two antenna elements have a U-shaped rectangular slot inserted between them. The detailed study of the suggested MIMO system includes measurement of the reflection parameter, analyzing the radiation performance, performing envelope correlation coefficient (ECC) and channel capacity calculations, and analyses of the effects of user’s hand in the vicinity of the antenna array. Simulation and measurement results demonstrate the required performance of the proposed design, that is, greater than 80% of total efficiency, isolation >12 dB, and ECC <0.15. The suggested antenna has the benefits of multiband operation, high efficiency, good isolation, and a small footprint.

A compact 12-element multiple-input multiple-output loop antenna array for a fifth-generation (5G) mobile phone is proposed. The operating band for the proposed antenna covers the long-term evolution 42 band, which spans a frequency range of 3.4–3.6 GHz. The size of the single antenna element is 5.85 × 4.9 mm2 (0.068λ0 × 0.057λ0), and 12 of these elements are positioned along two side edges of the mobile phone. This antenna is suitable for high screen-to-body ratio devices. The measured 6-dB impedance bandwidth is from 3.4 to 3.73 GHz. The measured total efficiency of the proposed antenna is 39–56% and the peak gain is 0–3.2 dBi. The transmission coefficient is less than −12 dB, the envelope correlation coefficient is less than 0.42, and the channel capacity is 45–50 bps/Hz.

An intra-band pattern-corrected decoupling vertical conducting wall is realized by dielectric substrate with conductor cladding on both side wall between two tightly spaced H-plane microstrip patches with λ0/20 edge-to-edge spacing. The wall is grounded and two symmetrical slots are etched on the vertical substrate. The measured results agree with the simulations, showing that the slotted vertical wall reduces the mutual coupling within the bandwidth to −30 dB and corrects the radiation beam tilt to be within −4.5° to 3° from the broadside direction. A gain reduction of 0.6 dB is observed compared to the gain without the slotted decoupling wall.

For forthcoming wireless applications, a small and highly decoupled complementary split ring resonators (CSRR)–loaded co-planar waveguide (CPW)–fed antenna for dual-band applications is investigated. The low-profile antenna consists of a CSRR-loaded rectangular radiating element with a truncated bottom, giving a wideband performance over the frequency ranges of 5.28–5.52 GHz and 6–7.2 GHz. The antenna has been printed on a widely used FR4 substrate measuring 7.5 × 10.5 × 1.6 mm3 in volume. This research’s suggested antenna is turned into a 4 × 4 multi input multi output (MIMO) construction using a 25 × 25 mm2 printed circuit board. Individual antennas were isolated by nearly 20 dB without using a decoupling device. The antenna has been built, and the measured and simulated results correspond well. Computing envelope correlation coefficient (ECC), channel capacity (CC), and channel capacity loss (CCL) further validates the antenna’s performance (−). The antenna has an overall gain of around 2.54 dBi and a radiation efficiency of approximately 89% throughout the relevant spectral range, which is much better for wireless applications. The suggested antenna’s omnidirectional emission pattern makes it a potential contender for future wireless and cellular applications.