This paper furnishes a compact modified hourglass-shaped aperture-coupled antenna for radar applications. The effect of slots of various shapes and various slot lengths on the input impedance, radiation pattern, and gain of the antenna are analyzed. The proposed antenna, designed using a modified hourglass-shaped aperture, offers a gain of 8.214 dBi for an compact antenna with a dimension of 20.4 × 20.4 × 1.041 mm3 and an aperture area of 2.495 mm2. Implementation of this proposed modified hourglass-shaped aperture offers a high gain per unit radiating patch area of 40.26 dB/$\lambda _g ^2$ and a high gain per unit aperture area of 1324.84 dB/$\lambda _g ^2$. The proposed aperture feeds a circular patch which radiates at its resonant frequency of 10.5 GHz. The proposed design is fabricated and the simulated results are verified experimentally. Equivalent circuit analysis is also done. A measured gain of 7.2 dBi is observed at 10.5 GHz. The physical area of the antenna is reduced without compromising the gain by judiciously choosing the shape of slot with more degree of freedom for impedance matching. The proposed antenna is well suited for the unit cell of phased array antennas for X-band missile radar applications.

By combining the technique of energy selective surface and frequency selective rasorber, an energy selective rasorber is proposed, which performs selective energy protection in the low communication frequency band (0.8–2 GHz) and wave-absorbing property in the high-frequency band (6–18 GHz). The design consists of two layers, of which the bottom one contains a lumped diode structure for energy selection function in the transmission band, while together with the top layer, they perform a wideband wave absorbing function. The simulated and measured results agree well with each other, and both show good absorption in 6–18 GHz and energy-selective property around 1.86 GHz. That is, when the incident power changes from −30 to 14 dBm, the reflection coefficient changes from below −22 dB to above −2 dB, while the transmission coefficient changes from above −3 dB to below −17 dB.

In this paper, a new design approach for the six-port (SP) junction is introduced. The proposed design includes a generalized broadband matching and smooth miniaturization scheme and is extendable for any passive multiport structure. A multilayer technology and a microstrip to slot coupling operation are employed for the designed SP, which comprises power divider and three hybrid couplers. The conducted measurements of the constructed SP junctions validates the design approach. Optimal performance of the SP network in terms of miniaturization, bandwidth, and response accuracy were obtained for the 5G low band.

This paper introduces a tri-band stacked elliptical patch antenna featuring a right-handed circular polarized, designed to operate at the L2, L5, and L1 Global Navigation Satellite System bands. Initially, an elliptic patch is constructed and fed by a probe feed to generate TM110 and TM210 modes at resonance frequencies calculated using Mathieu functions. The probe position is precisely adjusted to excite the quasi-orthogonal mode of TM110 to generate circularly polarized (CP) waves at the L2 and L5 bands. Subsequently, an eye-shaped aperture is engraved into the elliptical patch to enhance the axial ratio (AR) beamwidth in the L2 and L5 bands and stimulate the orthogonal mode of TM210 to produce CP waves at the L1 band. Lastly, a stacked partially elliptical parasitic element is placed beneath the upper slotted elliptical patch to enhance the orthogonality of TM210 surface current versions and thus improve the AR beamwidth at the L1 band. The proposed antenna shows low reflection coefficient values at 1.12–1.33 (L2/L5), and 1.5–1.66 GHz (L1). The AR beamwidths are 133/213∘, 167/163∘, and 36/103∘ at two orthogonal cutplanes at L5, L2, and L1 bands, respectively. The antenna also has decent gains of 6–6.9 dBic across the three bands.

Frequency-modulated continuous-wave radar systems profit from increasing the absolute bandwidths of the generated frequency chirps to improve range resolution. As the relative bandwidth of SiGe-voltage-controlled oscillators (VCOs) is limited to about 80%, increasing the center frequency fundamentally or via frequency multiplication is the most direct way to increase that absolute bandwidth. However, as some applications require penetration depth, which dramatically decreases with frequency, other solutions are necessary. Therefore, state-of-the-art concepts rely on the down-conversion of generated frequency chirps via two separately stabilized frequency sources. This article implements a novel architecture, offering relative bandwidths of >100% within a single phase-locked loop (PLL). Therefore, two VCOs at different center frequencies are fed into a down-conversion mixer, whose output is directly stabilized via that PLL with one loop filter generating both tuning voltages. Those circuit blocks can be summarized as one equivalent VCO, offering a higher relative bandwidth and a significantly more linear tuning curve. Thereby, a solution to limited relative bandwidths with high VCO gain variation of single VCO synthesizers is offered while substantially reducing the hardware and implementation effort compared to the state-of-the-art.

In this paper, the design of frequency reconfigurable planar antenna by incorporation of metasurface superstrate (FRPA-MSS) is presented using an artificial neural network. The dual-layer radiating structure is created on a 1.524 mm thick Rogers RO4350B substrate board (εr = 3.48, tan δ = 0.0037). The candidate antenna is designed and analyzed using a high-frequency structure simulator (HFSS) tool. The transfer matrix method is employed for the successful retrieval of electromagnetic properties of the metamaterial. Frequency reconfiguration is achieved by placing the metasurface superstrate onto the rectangular patch antenna. A simplified ANN approach has been employed for the design of metasurface incorporated proposed antenna. Presented prototypes are characterized through experimental measurements. It is found from the practical observations that the proposed antenna effectively reconfigures the tuning range from 5.03 to 6.13 GHz. Moreover, the presented antenna operates efficiently with agreeable gain, good impedance matching, and stable pattern characteristics across the entire operational bandwidth. The experimental results obtained validate the simulated performance.

This paper presents design of quintuple-mode wideband bandpass filters, implemented with off-centered perturbed metallic cylinders in a rectangular waveguide cavity. Three perturbation cylinders are placed at the bottom of the rectangular waveguide cavity, along with a pair of perpendicularly fed coaxial lines; excite five quasi-transverse magnetic modes to realize the desired passband. The height of the waveguide cavity and the shape of the perturbation cylinders are exploited to shift the resonant modes far away from the passband and achieve a good out-of-band rejection and sharp skirt selectivity. The filter operates at the center frequency of 2.68 GHz with a wide fractional bandwidth of 43%. The proposed filter is fabricated with aluminum. The measured and simulated results are in good agreement with each other.

In this paper, a novel multilayer substrate integrated dual-mode dielectric resonator (DR) filter is proposed. The square dual-mode DR is made of the high permittivity substrate by removing the undesired portions and the surface coppers so that the relatively high unloaded quality factor of the dominate TM11 pair can be obtained which compared to these fully dielectric-filled substrate integrated waveguides. Meanwhile, it can be easily integrated in an equivalent cavity implemented by multilayer printed circuit boards for filter design, showcasing low in-band loss, light weight, and compact size. For demonstration, a multilayer substrate integrated DR bandpass filter centered at X-band is designed and measured. Good agreement between the simulated and measured results can be observed, and the measured insertion loss at the passband center frequency (8.38 GHz) is 1.1 dB.

A method allowing for reduction of coupling coefficients required for realization of two-section asymmetrical coupled-line directional couplers has been proposed. It has been shown that by connecting uncoupled left-handed and right-handed transmission lines between two coupled-line sections one can obtain greater design flexibility of the resulting circuit, simultaneously with the coupling reduction in coupled-line sections. Moreover, the proposed circuit features the properties of two-section asymmetric directional couplers offering wide operational bandwidth. The theoretical analysis has been verified by measurements of a 3 dB directional coupler operating at the center frequency f0 = 1.5 GHz having coupling imbalance δC = ±0.4 dB and bandwidth 0.75–2.3 GHz.

We present the implementation of a cooperative radar system on a gantry rail crane for distance measurements in an industrial environment. The measurement approach is based on the dual-ramp frequency-modulated continuous-wave principle, using identical sensor-nodes at the endpoints of the range of interest. Pseudo-range information is exchanged via a dedicated data-link between these stations. At the sensor-node a flexible high-performance signal processing and remote management engine is implemented. The system setup is controlled by a single host-PC, which is used as a man–machine interface for configuration of the remotely controlled measurement stations, system surveillance, and visualization of the measurement data. Indoor characterization of the developed hardware is sufficient for an efficient calibration of the system, minimizing distance offsets. On-site measurements at distances up to 1000 m with an accuracy better than 2 cm confirm the performance of the ranging system. Furthermore, the results are verified by simulation.

An FM-ultra-wideband (UWB) system with a wideband RF carrier (WRC) is proposed for wireless body area network applications. The proposed system can control the channel power by means of an adjustable carrier bandwidth (BW), while the conventional one with a CW carrier (CWC) makes use of peak power control. The implemented WRC system performances have been evaluated for the WRC generation and digital data transmission. In addition, transmission performances have been compared with that of a conventional CWC system by bit-error-rate (BER) tests. For random data of a 29−1 pattern at a data-rate of 64 kbps, in spite of the flexible carrier BW, the WRC system has presented excellent transmission capability compared with that of the CWC system.

This paper investigates metamaterials composed of resonant particles with negative electric polarizability located in a three-dimensional net. The main problem in fabricating these materials is the spread of the resonant frequencies of particular planar resonators. This spread is caused by the tolerances of the fabrication process for planar resonators. The simulation shows that there is a limit to the dispersion of resonant frequencies that allow the metamaterial to behave as a metamaterial with negative effective permittivity. Two metamaterials with a negative real part of the effective permittivity were designed on the basis of simulations. The first metamaterial has a regular periodic structure. The second is a metamaterial in which the resonant particles are randomly distributed both in space and in orientation, and it offers an isotropic response. This metamaterial was fabricated by inserting planar resonators into plastic shells that can be poured into any volume and ensure a random distribution of the resonant particles in space. The results of the simulations have been verified by measurements.

In this paper, a microstrip lowpass filter adopting two main resonators with steep transition band and wide rejection band has been introduced. The first main resonance cell consists of meandered transmission lines which are loaded by modified T-shaped patches. The second main resonator is composed of high-impedance lines loaded by polygon patches. To obtain a steep skirt performance, the first and second resonators have been combined. Moreover, employing eight high–low impedance folded stubs and two rectangular open-stubs as suppressing cells has resulted in improving the stopband features. To comprehend the frequency behavior of the employed resonators and also their combination, the formulas of the transmission coefficient, reflection coefficient, and the transmission zeros of their equivalent LC circuits have been extracted, separately. According to the measurement results, the −3 dB operating frequency of this filter is 1.65 GHz. Moreover, a relative stopband bandwidth equal to 166% with a corresponding attenuation level of 23 dB and a sharp roll-off rate (393.61 dB/GHz) have been achieved. In the passband region from DC to 1.632 GHz, the insertion loss and return loss are better than 0.0763 and 15.85 dB, respectively, proving an acceptable in-band performance. Finally, the implemented structure brings about a high figure-of-merit equal to 81 672.

This work presents the design of two compact multi-standard low-noise amplifier (LNA) in a 28 nm low-power bulk CMOS process. The transistor parameters were optimized by the gm/ID method taking into account the parasitics and the behavior of highly scaled transistors. To cover the industrial science medical (ISM)-bands around 2.4 and 5.8 GHz, the WLAN band as well as the Ku band a bandwidth enhancement is required. Two versions of LNAs, one with vertical inductors and one with active inductors, are implemented and verified by measurements. The noise figure (NF) exhibits 4.2 dB for the LNA with active inductors and 3.5 dB for the LNA with vertical inductors. The voltage gain reaches 12.8 and 13.4 dB, respectively, with a 3 dB-bandwidth of 20 GHz. Both input referred 1-dB-compression points are higher than −12 dBm making the chips attractive for communication standards with high linearity requirements. The chips consume 53 mW DC power and the LNA with active inductors occupies a core area of only 0.0018 mm2, whereas the version with vertical inductors requires 0.021 mm2.

Due to increasingly complex and automated manufacturing processes, the demands on the control parameters of these processes are also increasing. In many applications, such a parameter is the fill quantity, whose precise determination is of ever growing importance. This paper shows with which accuracy and precision an M-sequence ultra-wideband radar can determine levels in small metallic and non-metallic containers with contact-based and contactless measurements. First, the principle of level measurement using guided wave radar is explained and the measurement setup is described. Afterward, the measurement results are shown and discussed. The measurements show that the level can be measured with an accuracy of better than 0.5 mm. In addition, level fluctuations can be detected with a precision of 3 ${\rm \mu }$m. Based on the results of the guided wave radar, the possibilities of volumetric contactless measurement using an electrically small patch antenna are discussed. A particular challenge in contactless level measurement is the high number of multipath components, which strongly influence the accuracy. In addition, there are near-field effects when measuring close to the antenna. Exploiting these near-field effects, an additional method to accurately determine the full state of the container is investigated.

This paper describes the experimental investigation of orthogonal time-frequency space (OTFS) modulation using a 28 GHz multi-user distributed multiple-input multiple-output (D-MIMO) testbed in over-the-air (OTA) and mobility environments to enhance cell throughput in a millimeter-wave band. We build the D-MIMO testbed having newly developed OTFS modulator and demodulator, and measured OTFS signals and orthogonal frequency-division multiplexing (OFDM) signals with up to four user simultaneous connections on an actual office floor. Additionally, the Doppler effect on OTFS signals is mathematically analyzed and is confirmed in the measurements. OTFS indicates higher robustness in time-variant channels than OFDM. The error vector magnitude (EVM) and system throughput of OTFS are −22 dB and 1.9 Gbps with 100 MHz signal bandwidth, respectively. To our knowledge, this is a first paper describing the OTA measurements of EVM, throughput, and spectral efficiency using OTFS modulation on the 28 GHz coherent beamforming system.

Through-wall imaging is capable of detecting various living and non-living things behind the wall. The characteristics of the wall under the investigation, amount of clutter and noise govern the quality and reliability of the image as well as the detection ability of the targets using through the wall imaging system. The characteristics of the wall are not known prior, in the literature only the intensity profile is investigated for the unknown wall characteristics using a single dielectric target and the effect of the wall characteristics on the contrast imaging and impact on time or frequency domain features are not investigated. The target with less dielectric is having less reflectivity; hence its detection in the presence of a high reflective target and a noisy environment becomes difficult. In this paper, to enhance the detection ability of the imaging system attenuation constant (α) of the wall is estimated with the proposed wall parameter estimation methods and used as a normalizing factor. To achieve effective beamforming different weighting strategies are developed and the obtained images are compared with the traditional beamforming. Furthermore, a novel approach to finding the effective rank in the low-rank estimation using a statistical model and multi-objective genetic algorithm is proposed for de-noising.

The direct measurement of the radiation pattern of an antenna is often unreachable. A near-field sampling followed by a near-field/far-field (NF/FF) transformation is therefore substituted. This process is, in most cases, applied to antennas placed in free-space or over a perfect electric conductor. On the contrary, few results concern real environment conditions. Nevertheless, it is well known that the nature of the soil can drastically change the radiating characteristic of an antenna. The lack of information about the behavior of the antenna in real conditions can give rise to substantial errors in the evaluation of the performances of electromagnetic devices. The aim of this paper is then to propose a new NF/FF transformation able to reliably supply the field radiated by an antenna placed over a plane, homogeneous, dielectric, and lossy interface. The method is based on the cylindrical-wave expansion of the electric field. The real soil is taken into account by means of its reflection coefficients. First results are given for simple antennas and for both transverse magnetic and transverse electric polarizations.

A novel dual-band planar antenna with a low profile for mobile communication system is proposed in this paper. The antenna is composed of one shorted patch with two radiating notches for low frequency resonance and one square patch for high frequency resonance. The low profile is achieved via the shorting patch, which introduces the parallel electrical field between the reflector and antenna. A step-impedance microstrip line is used to feed the antenna. The coupling between the square patch and microstrip line cancels out the inductance of shorting probe, which increases the working bandwidth of proposed antenna. A prototype with a low profile of 0.0286λ is fabricated and measured. The antenna achieves dual impedance bandwidths of 1.6% for the low frequency band and 60% for the high frequency band, covering the frequency range 851–865 MHz and 1.97–3.65 GHz, respectively. The measured results show good agreements with the simulated ones.