Experimental and computational investigations have been made to obtain the details of the flow field of a supersonic air-intake with different cowl deflection angles and back pressures at the exit. The flow field obtained with an inviscid computation on the basic configuration, designed for Mach 2·2, shows starting behaviour whereas computation with k-ω turbulence model and experiments indicate unstart characteristics. Both experiments and computations indicate that provision of a small angle at the cowl tip leads to start of the same intake and also improves it’s performance. Results obtained with cowl deflection shows a better performance in comparison to performance achieved with a basic intake and with a bleed of 2·8%. Sustainable back pressure could be obtained through the computations made at different back pressures for different cowl deflection angles. Overall results suggest that provision of small cowl deflection angle itself leads to improvement in performance achieved in comparison to a bleed of 2·8%, even with back pressure at the exit.

Although many researchers, from a number of industries, have studied the aerodynamics of ground effect conditions, published research remains inconclusive. Published results are frequently found to conflict and modeling procedures (in both computational and experimental situations) vary. In this paper, existing research is reviewed and the methods used in obtaining the results are compared. Possible causes for the discrepancies in the published work are outlined, including the inappropriate specifications of boundary conditions and the neglect of viscosity in some computational analyses. Computational and experimental analyses are then performed to determine if these identified areas do cause inconsistencies in results and to also determine accurate simulation procedures.

The stability of a two-dimensional wall jet was studied theoretically and experimentally. As a result of the linear stability calculation, it was found that one eigenmode is separated into two modes when the Reynolds number is large, and inside a neutral stable curve in the α, R-plane there exists another neutral curve enclosing a stable region. Experimental results of small disturbances were compared with calculated results; agreement between them was satisfactory. It was found, further, that subharmonics of a predominant disturbance velocity component appear in the non-linear region.

Work on the finite element analysis of flat plates in bending has been directed towards elements which satisfy kinematic conditions between the adjacent elements in conjunction with the theorem of minimum potential energy, eg Argyris, Bazeley et al, Clough and Veubeke.

The purpose of this Note is to provide the main details of a triangular element which satisfies equilibrium conditions between the adjacent elements and which is used in conjunction with the complementary energy principle. The bending moments vary linearly within the element and use is made in the derivation of the analogy (see eg Southwell, Fox, Fung and Morley that exists between problems of plane stress and plate bending. In particular, many of the present details are taken directly from the plane stress analysis of Veubeke who, along with Argyris, considers a displacement triangular element with linearly varying strain.

A computer program for use in the conceptual stage of aircraft design has been developed. The program obtains minimum mass designs for high aspect ratio, composite wings, subject to constraints on flutter speed, divergence speed and material stress. The wing is modelled as a series of composite beam elements and both flutter speed and divergence speed are calculated using a normal mode approach. Modal analysis is carried out by applying the Wittrick-Williams algorithm to the dynamic stiffness method, whereas unsteady aerodynamic loads are calculated from strip theory, although an option which uses lifting-surface theory is also presented. A previously published example is given to validate the analysis. Single level optimisation is carried out using a sequential quadratic programming strategy combined with the modified methods of feasible directions optimizer, for which flutter sensitivities are obtained by an efficient determinant interpolation technique. Design variables include topological variables such as spar and engine positions as well as layer thicknesses, which are modelled using quadratic functions. The wing of a regional turboprop aircraft is optimized to illustrate the use of the program. The problem was modelled using 10 elements and had 43 design variables, 162 constraints and required just over 20 minutes of CPU time on a workstation. This, coupled with the fact that a full three-dimensional FE model of the same wing would require over 1000 elements, illustrates the suitability of the dynamic stiffness method to the conceptual design stage.

For plane turbulent jets and wall jets in uniform streaming flow a simple method, based on a simple empirical formula for the rate of growth which differs from that proposed by Abramovich, is presented. The predictions of length scale, l0, and velocity scale, u0, are in good agreement with experimental results for all ratios of free-stream to jet exit velocity and the eddy viscosity Reynolds number has the correct asymptotic values.

The paper presents a solution to the buckling of infinitely long plates clamped along the edges, together with an extension of the solution obtained by Stein and Fralich for the case when the edges are simply-supported. It is shown that, as a consequence of increasing the edge support from that of a simple support to one in which both deflection and rotation are prevented, the rigidity which an intermediate transverse stiffener must possess in order to support the plate effectively is much reduced. Agreement between the theoretical relationships and existing experimental data is good.

Measurements made at a Mach number of 0.18 and a chord-based Reynolds number of 4·2 x 106 on a constant-chord model having a NACA 4412 aerofoil section are described and compared with the results of flow field calculations.

Both the experimental arrangement and the difficulties initially experienced in achieving an adequate approximation to two-dimensional flow above the wing are briefly outlined.

The measurements include static pressure distributions on the wing surface and on the wind-tunnel walls above and below the mid-span section of the wing. The main emphasis in the experiment was, however, on defining the development of the upper surface boundary layer through separation (at about 20% chord ahead of the trailing-edge) and on into the wake, making extensive use of laser anemometry to measure mean velocities. In addition, Reynolds stresses were measured in certain parts of the flow field by hot-wire anemometry.

The flow field calculations are of the semi-inverse kind in which an inverse momentum-integral treatment of the shear flow, used to avoid difficulties at separation, is coupled to a direct solution of the inviscid flow problem. The main features of the method are outlined.

A numerical model is developed for predicting low-velocity impact damage in laminated composites. Stacked shell elements are employed to model laminate plies with discrete interface elements in pre-determined zones to model the onset and propagation of matrix cracks and delamination. These interface elements are governed by a bi-linear cohesive failure law. Cohesive element zone size is determined by a separate finite element analysis using solid elements to identify the stress concentration sites. In order to save the computational effort, low-velocity impact load is modelled by quasi-static loading. Influence of contact force induced friction on shear driven mode II delamination is modelled by a friction model. For a clustered cross-ply laminate, calculated impact force and damage area are in good agreement with the test results. It is shown that matrix cracks should be included in the model in order to simulate delamination in adjacent interface. The practical outcome of this research is a validated modelling approach that can be further improved for predicting low-velocity impact damage in other stacking sequences.

Key issues relating to the Supersonic Business Jet (SBJ) concept are reviewed with the intent to assess the readiness of enabling technologies and hence the concept itself. The multidisciplinary nature of aircraft design precludes an in-depth analysis of each specific aspect, which could individually be the subject of a separate discipline review, hence an overview is presented.

The review looks at the market, environmental issues, with particular reference to the sonic boom phenomenon & solutions, technological issues, including prediction methods, flight testing, systems, certification and interested aerospace companies and design organisations.

It is apparent that the need to reduce the sonic boom signature is vital if the vehicle is to be permitted to operate over land and hence be economically viable. It is clear that sonic boom acceptability requirements must be set if resources are to be effectively focused and designs are to converge. Despite this challenge, considerable investment is aimed at de-risking many of the enabling technologies and raising readiness levels. Many technologies are moving beyond theoretical and numerical analysis into the experimental and flight test domains. Collaboration between the civil and military sectors is increasing.

Clearly, supersonic air travel is not an efficient means of personal conveyance; however, concerns for the environment are difficult to balance against the ‘value of time’ benefits offered by the SBJ concept. Air travel, of which this is a specialised form, is important to the global economy. Continued effort in the areas of human factors, customer demand and certification & requirements would be beneficial.

It is shown that the flow in a region of recirculation may be divided into a core, in which the vorticity may be constant, and a boundary layer surrounding the core. An approximate solution is given for the flow inside a circular cylinder with partly fixed and partly moving walls.

Flow patterns which include regions of recirculation occur frequently, for example, behind bluff bodies, in sharp bends, and in sudden expansions in ducts. Little is known about this type of flow, which will be referred to, for brevity, as ‘cavity’ flow. It used to be thought that the velocities in the ‘ cavity ’ were small compared with the stream velocity, but it is now known that the maximum velocity in the cavity may be about 30 per cent. of the stream velocity. This implies that the motion within the cavity cannot be neglected.

The main factor contributing to hydroplaning on slick runways is the existence of a squeeze film in the contact area between tyre and surface. The situation may be improved by optimising surface texture so that the asperities break through the water film in a minimum time. Two techniques are described for characterising surface texture: a superposition solution based on viscous channel flow and a dimensionless number approach involving size, spacing and shape factors. The “feel” of a surface is quantitatively obtained, and an outflow meter is described which, by directly measuring the mean hydraulic radius of runways, provides a comparison of their drainage abilities.

A double Fourier series solution is presented for the buckling of simply supported orthotropic and isotropic skew plates, subjected to in-plane compressive and shear edge loads. All the boundary conditions, including the vanishing of the normal bending moment along the edges, are satisfied. Numerical results, suitable for design purposes, are presented graphically for a number of independent parameters such as skew angle, ratio of flexural rigidities and aspect ratio. The results show that the buckling strength is substantially effected by the skew angle, and to a lesser extent, by the ratio of the flexural rigidities and aspect ratio. In contrast with positive shear edge loads, which tend to decrease the skew angle, negative shear edge loads appear to reduce the buckling strength of orthotropic and isotropic skew plates.

New wind tunnels appear fairly infrequently and are usually of individual design to meet specific requirements and constraints. Detailed information on existing tunnels can be of great benefit to the designer, enabling him to avoid expensive pitfalls and to capitalise on the successful features that have evolved over the years. For this reason, and to advance wind tunnel design generally, new designs should be reported. The following account is presented in this light, even though the low speed tunnel described is unremarkable, being of conventional design and modest proportions. Indeed, its design follows closely the guide-lines laid down for such tunnels by Bradshaw and Pankhurst, guide-lines which themselves draw on the cumulative experience gained from previous low speed wind tunnels. The satisfactory performance of the tunnel is in no small measure the result of this approach.

The development of new technologies – such as rapid prototyping – and the use of materials with improved properties – such as highly resistant extruded polystyrene foam which can be easily and precisely shaped, while conserving its mechanical properties – allow researchers to improve design concepts. This article details the development of a new set of morphing wings for a 15-kg maximum take-off weight Unmanned Aerial Vehicle (UAV) from concept design, to flight tests, including modelling, design optimisation, construction and wind-tunnel tests. A set of comparator-equivalent conventional wings have been used throughout in order to be able to judge any benefits stemming from the adoption of morphing technology. This article shows that the morphing wings provide a controllable aircraft while reducing drag by a factor of 40% compared to the comparator wings with conventional ailerons in a deflected position.

The “frozen stress” techniques of photoelasticity can give a complete knowledge of the stress, system in a solid body, but the examination of the stresses requires more time and care than in corresponding flat plate tests. In tests on tubes with transverse circular holes, sponsored by The Royal Aeronautical Society, all practicable geometrical shapes are examined and the maximum stress is measured in tension, bending and torsion. The results are comprehensive and show the inadequacy of previous results. In all cases the maximum stress occurs inside the bore of the hole. The accuracy of all the graphs of stress concentration factors is better than five per cent.

An improved version (HLLC) of the Harten, Lax, van Leer Riemann solver (HLL) for the steady supersonic Euler equations is presented. Unlike the HLL, the HLLC version admits the presence of the slip line in the structure of the solution. This leads to enhanced resolution of computed slip lines by Godunov type methods. We assess the HLLC solver in the context of the first order Godunov method and the second order weighted average flux method (WAF). It is shown that the improvement embodied in the HLLC solver over the HLL solver is virtually equivalent to incorporating the exact Riemann solver.

A study has been made of the effects of inlet coolant injection upon axial compressor performance, using the results of tests on turboshaft engines. It is shown that evaporation of the coolant changes the stage work distribution as well as the ideal compression work and that these effects may be estimated by elementary thermodynamic methods. Simplified prediction procedures are suggested and compared with experimental results.

Model scale tests of modern ‘open rotor’ propulsor concepts that have potential for significant fuel burn reduction for aircraft applications were completed at NASA Glenn Research Center. The recent test campaign was a collaboration between NASA, FAA, and General Electric (GE). GE was the primary industrial partner, but other organisations were involved such as Boeing and Airbus who provided additional hardware for fuselage simulations. The open rotor is a modern version of the UnDucted Fan (UDF®) that was flight tested in the late 1980s through a partnership between NASA and GE. The UDF® was memorable for its scimitar shaped propeller blades and its unique noise signature. Design methods of the time were not able to optimise for both high aerodynamic efficiency and low noise simultaneously. Contemporary CFD/CAA based design methods can produce open rotor blade designs that maintain efficiency with acceptable acoustic signatures. Tests of two generations of new open rotor designs were conducted in the 9’ × 15’ Low Speed Wind Tunnel and the 8’ × 6’ Supersonic Wind Tunnel starting in late 2009 and completed in early 2012. Aerodynamic performance and acoustic data were obtained for take-off, approach and cruise conditions in isolated and semi-installed configurations. Additional detailed flow diagnostic measurements and acoustic measurements, including canonical shielding configurations, were obtained by NASA. NASA and GE conducted joint systems analysis to evaluate the performance of the new blade designs on a Boeing 737 class aircraft. The program demonstrated a 2-3% improvement in overall net efficiency relative to the best efficiency designs of the 1980s while nominally achieving 15-17 EPNdB noise margin to Chapter 4 (at a Technology Readiness Level of 5) for a notional aircraft system defined by NASA.

An experimental investigation is presented to validate endurance estimates for a battery powered flight vehicle. In this study a radio controlled model aircraft was ‘flown’ inside a wind tunnel. Various Lithium Ion batteries were used to power the model. Battery electrical characteristics were recorded during each run to assess battery discharge behaviour. Theoretical estimates based upon battery characteristics yielded endurance estimates within 3% of that measured experimentally. The discharge characteristics of the batteries were found to be the largest source of uncertainty for endurance estimates.