The flow near the trailing edge of a circulation-controlled aerofoil is studied. The circulation is controlled by tangential blowing around the bluff trailing edge of the aerofoil.

Velocity profiles in the blowing jet on the trailing edge of a circulation-controlled aerofoil have been measured and a calculation method has been developed for this type of circulation control. The development of the blowing jet is calculated by means of a velocity-profile equation, an angular-momentum integral equation, and an entrainment equation. Improved criteria are suggested for establishing the starting conditions for the development calculation. A realistic method is presented for taking into account the effects of the boundary layer which develops upstream of the blowing slot. A separation criterion for turbulent wall jets and a curvature correction for the entrainment rate are proposed. The calculated blowing-jet developments are found to be in good agreement with experiment. There is fair agreement between the calculated and measured blowing rates required to produce given lift coefficients on the aerofoil.

The paper presents a solution for the buckling under shear of a rectangular plate which is clamped along one edge and simply-supported along the other edges. The authors have also re-examined the case of one pair of opposite edges clamped and the other pair simply-supported.

A description is given of a supersonic pressure-tube wind tunnel which has been constructed at A.R.D.E. This is a blow-down tunnel which uses as a reservoir a long tube filled with gas under pressure. A quasi-steady supersonic flow is achieved by expanding in a convergent-divergent nozzle the subsonic flow behind rarefaction waves which propagate down the tube when a diaphragm at the nozzle exit is burst. The theory of the operation of the tunnel is given and calculations are made of the boundary-layer growth along the tube. Pressure-time records were obtained in the tube, and a high speed camera was used to obtain pictures of the flow round a model. Measurements also included a pitot-tube traverse of the nozzle exit, and the Mach number distribution was determined from the ratio of the pitot to the stagnation pressure. Tests showed that, as predicted, a constant stagnation pressure was obtained ahead of the nozzle, and it is considered that a tunnel of this type would be a cheap and simple way of obtaining an intermittent tunnel with adequate running time for many types of test, and capable of operating at a Reynolds number of more than 107 per inch at a Mach number of about 3·5.

This paper describes the work done to achieve high parallel performance for an unstructured, unsteady turbomachinery computational fluid dynamics (CFD) code. The aim of the work described here is to be able to scale problems to the thousands of processors that current and future machine architectures will provide. The CFD code is in design use in industry and is also used as a research tool at a number of universities. High parallel scalability has been achieved for a range of turbomachinery test cases, from steady-state hexahedral mesh cases to fully unsteady unstructured mesh cases. This has been achieved by a combination of code modification and consideration of the parallel partitioning strategy and resulting load balancing. A sliding plane option is necessary to run fully unsteady multistage turbomachinery test cases and this has been implemented within the CFD code. Sample CFD calculations of a full turbine including parts of the internal air system are presented.

Increasingly stringent operational demands on military aircraft, together with the widening flight envelopes made possible by advances in aerodynamic, structural and propulsion technology, have forced the complication of stability and control augmentation systems (S/CAS) upon the aircraft designer. The early SAS configurations were conceived as devices to enhance the natural response characteristics of the aircraft; later, CAS evolved as a way of making the desired response more independent of the basic aircraft characteristics. Many recent examples of S/CAS are very complex, with equations of twentieth or higher order commonly being used for linear handling qualities analysis. In view of the fact that aircraft of this complexity have been part of the handling qualities picture for ten years or more, it is surprising that no widely accepted criteria for these aircraft have evolved.

In commercially available gas turbine performance simulation tools, individual engine components are typically represented with non-dimensional maps of experimental or default data. In those cases where actual component characteristics are not available and default characteristics are used instead, conventional tools can deviate substantially at off-design and transient conditions. Similarly, when real component characteristics are available, conventional engine cycle simulation tools can not predict the performance of the engine at other than nominal conditions satisfactorily, or account for the impact of changes in component geometry.

This study looked into the full integration of two-dimensional streamline curvature component models with a low fidelity cycle program. Firstly, the obtained engine performance was compared against the one calculated based on default component characteristics. As a second case study, a range of flight Mach numbers and angles of attack were examined together with the effect of three different intake lip geometries on the performance of a notional, two-spool, low-bypass ratio, military engine. Two-dimensional models were used in the engine cycle analysis to provide a more accurate, physics- and geometry-based estimate of intake and fan performances.

The analysis carried out by this study demonstrated relative changes in the predicted engine performance larger than 1%. For briefness, representative results are presented and discussed in this paper for one flight Mach number and angle of attack setting. More importantly, this research effort established the necessary methodology and technology required towards a full, two-dimensional engine cycle analysis at an affordable computational resource in the very short term.

The appearance of the Kármán vortex street in the wake of bluff bodies has been well-known for sixty years. But the simple question of whether it appears also in the wakes of two cylinders in tandem at the same speed range, seems to have been unanswered as yet. The main reason for this is presumably the lack of practical interest. The only exception was in the early years of aviation in the era of biplanes. The use of streamlined or cylindrical struts was common and stimulated the investigations of Panell et al 1915, Wong & Yu 1917, Frazer & Simmons 1917, Biermann & Herrnstein 1933, and others.

In this note, the experimental results of wind-tunnel measurements of lift coefficient and lift-curve slope for aerofoil NACA 0012 obtained from the VTI-Institute Zarkovo, are presented. The results were obtained from tests and integrations of surface static-pressure data over a model of the NACA 0012 aerofoil section. The data were obtained for a free-stream Mach number range of 0·25-0·8 and a chord Reynolds number range of 2-25MRe. The essential results of these measurements along with the results from other authors are presented and evaluated. The principal factors which influence the accuracy of two-dimensional wind-tunnel test results are analysed. The influences of Reynolds number, Mach number and wall interference with reference to solid and flow blockage as well as the influence of side-wall boundary-layer control are analysed. Interesting results brought to light the Reynolds number effects of the test model versus Reynolds number effects of the facility in subsonic and transonic flow as well as the effects of the side-wall boundary-layer control and wall interference.

The motion of liquid in the containers of a vehicle may have severe influence upon the stability of the vehicle. For this reason many authors have investigated the behaviour of liquid with a free surface due to various modes of excitation. In the earlier development of small vehicles, the frequencies of the elastic structures were relatively high compared to the propellant frequencies and the effect of their interaction could be neglected. With the increase of modern space vehicles this interaction of the propellant with the elastic structure is becoming a pronounced influence upon the design of the vehicle and its control system. This has some influence upon the stability and response behaviour of a large space vehicle, since the close grouping of propellant sloshing and structural frequencies around the control frequency of the vehicle creates continuous interaction during flight.

In this paper a non-linear theory of the supersonic bangs from an accelerating body is worked out, using an extension of Whitham’s method. The strength of the bow shock is determined, and it is shown that the effect of acceleration on the pressure rise is appreciable at large distances from the nose for Mach numbers near unity. The results are compared with those of linear theory; the estimate for the pressure rise is found to be about a half of the linear value. The results also include an expression for the curvature of an attached shock at the nose, and a formula for the decay of a shock after it is detached from a decelerating body.

A novel, non-intrusive, high spatial and temporal resolution thermal imaging system, based on the fluorescence properties of a dysprosium doped yttrium-aluminum-garnet (Dy3+:YAG) thermographic phosphor, has been developed. In this system, the phosphor coating on the test surface is excited by a pulsed Nd:YAG laser. The resulting fluorescent emission of the temperature sensitive 456nm transition and that of the temperature independent 496nm transition, are acquired using a pair of image-intensified charged coupled device cameras. The ratio of the acquired emissions is then correlated to temperature. The Dy:YAG phosphor displays temperature sensitivity in the range of 295–l,350K (with possibility up to 1,800K). Temperature measurements obtained from the surface of a disk heated by an impinging jet, demonstrate the feasibility of this technique for general heat transfer studies involving significant unsteadiness and transient phenomena.

This paper deals with the force coefficients on the leeward of two bluff bodies, in particular with the origin and nature of the lift force. Initially a general description of the characteristics of the force coefficients, plus the effect of parameters such as free-stream turbulence and surface roughness in the form of stranding, is given.

A resume of all the known suggestions for the origin of the lift force is listed and a series of experiments, attempting to test these suggestions using simple methods, is described. These methods consist mainly of force measurement, involving force measurement on the leeward conductor using different shapes for the leeward and windward bodies. However, static pressure tapping and flow visualisation are also employed to a small degree.

It is shown that none of the suggestions gives a satisfactory explanation for the origin of the lift force. However, several interesting points were noted; for instance the dependence of the lift profiles for the leeward body on its own characteristics in the wake and not particularly on the wake characteristics. Hence it is shown that the use of wake parameters, measured without the presence of the leeward body when attempting to assess the forces thereon, is an over-simplification of the situation as far as lift is concerned while appearing to work quite well for drag.

This paper presents performance analysis and design of ducted propellers for lighter-than-air vehicles. High-fidelity computational fluid dynamics simulations were first performed on a detailed model of the propulsor, and the results were in very good agreement with available experimental data. Additional simulations were performed using a simplified geometry, to quantify the effect of the duct and of the blade twist on the propeller performance. It was shown that the duct is particularly effective at low flight speed and that the blades with relatively high twist have better performance over the flight envelope. Design of the optimal twist distribution and of the duct shape was also attempted by coupling the flow solver with a quasi-Newton optimisation method. Flow gradients were computed by solving the discrete adjoint of the Reynolds-averaged Navier-Stokes equations using a fixed-point iteration scheme or a nested Krylov method with deflated restarting. The results show that the ducted propeller propulsive efficiency can be increased by 2%.

Spanwise velocity correlations of the turbulent vortices shed by a two-dimensional bluff body of D-section are presented for different aspect ratios of the shedding body between end-plates. From these it is shown that the vortices are only shed two-dimensionally when the gap between the end-plates is less than or equal to four times the base height of the shedding body.

Research is at present being carried out at the Turin Polytechnic University with the aim of designing an HAVE/UAV (high altitude very-long endurance/unmanned air vehicle). The vehicle should climb to 17-20km by mainly taking advantage of direct Sun radiation and thereafter maintain a level flight; during the night, a fuel cells energy storage system would be used. A computer program has been developed to carry out a parametric study for the platform design. The solar radiation change over one year, the altitude, masses and efficiencies of the solar and fuel cells, and the aerodynamic performances have all been taken into account. The parametric studies have shown how fuel cells and solar cells efficiency and mass have the most influence on the platform dimensions. A wide use of high modulus CFRP has been made in designing the structure in order to minimise the airframe weight. A first configuration of HELIPLAT® (HELIos PLATform) was worked out, following a preliminary parametric study. The platform is a monoplane with eight brushless electric motors, a twin-boom tail type with an oversized horizontal stabiliser and two rudders. The co-ordinates at the root and along the wing span as well as the wing planform were optimised to achieve the best efficiency. Several profiles and wing plans have been analysed using the CFD software Xfoil and Vsaero. Several wind-tunnel tests were carried out to compare the analytically predicted performances. A preliminary design of a scale-sized technological demonstrator was completed with the aim of manufacturing a proof-of-concept structure. A FEM analysis was carried by using the Msc/Patran/Nastran code to predict the static and dynamic behaviour of the UAV structure.

As part of a series of investigations of the swirl in S-ducts, the present paper gives the results of tests on a duct with both horizontal and vertical offsets, for comparison with earlier work on ducts with horizontal offset only. Results obtained bear a similarity to those of Reference 2, for which the duct had the same cross-sectional shapes and areas, but the addition of a vertical offset magnifies the resultant swirl considerably. As before, the swirl is found to be sensitive to entry conditions, in that a solid spoiler, blocking off 15% of entry width from the inside wall, reverses the sense of the final swirl. Taken overall, the results throw additional light on the nature of the swirl problem. A particularly interesting and potentially important correlation is obtained between the final swirl (in magnitude and sense of rotation) and a pressure difference between the top and bottom walls of the duct, taken in the end plane of the second bend.

Studies begun over ten years ago have shown that the swirling air flow about the tips of a lifting wing can be redirected using small aerofoil surfaces, called sails, to reduce the overall lift-dependent drag of the wing. Tests on Paris, Jetstream and other windtunnel models, confirmed by flight tests on Paris and Centurion aircraft have shown marked reductions in drag and fuel consumption. Handling tests show improvements in roll control and stalling speeds.

Wing tip sails have the effect of reducing the peak adverse effects on other aircraft flying through the wake of a Paris aircraft but reduce the decay rate so the far field effects are worsened. Sails fitted to a crop-spraying aircraft have significantly reduced the amount of spray lifted above the height of the aircraft by the tip vortices and subsequently blown off-target by a cross-wind.

Windtunnel tests on a model with variable incidence sails show that differential sail incidence can be used effectively to provide roll power, reducing the size of the ailerons required, so allowing a greater flap span. The maximum root bending moments of the wings can be reduced by at least 10% by using negative sail movements in positive manoeuvres or gusts.

Sails can reduce the drag of an aircraft at all speeds leading to fuel savings estimated at US$225 per annum per 1000lb take-off weight per 1000 hours annual utilisation. For an airliner of 300 000lb weight and operating for 3000 hours this means a fuel saving of over a fifth of a million dollars per year!

Numerical analysis of the flow in weapon bays modelled as open rectangular cavities of length-to-depth (L/D) ratio of 5 and width-to-depth (W/D) ratio of 1 with doors-on and doors-off is presented. Flow conditions correspond to Mach and Reynolds numbers (based on cavity length) of 0·85 and 6·783m respectively. Results from unsteady Reynolds-averaged Navier-Stokes (URANS), large-eddy simulation (LES) and detached-eddy simulation (DES) are compared with the simulation methods demonstrating the best prediction of this complex flow. It was found that URANS was not able to predict the change of flow characteristics between the doors-on and doors-off configurations. In addition, the energy content of the cavity flow modes was much better resolved with DES and LES. Further, the DES was found to be quite capable for this problem giving accurate results (within 3dB of) experiments and appears to be a promising alternative to LES for modelling massively separated flows.

An experiment was made on a turbulent boundary layer with adverse and favourable pressure gradients alternating twice along the stream. The most important findings of the present study are as follows. In the region of the adverse pressure gradient downstream of the strong acceleration, an internal boundary layer develops within the boundary layer. In this internal layer large advection of turbulent energy occurs and the flow is locally non-equilibrium even near the wall. As a result the usual logarithmic law and turbulence similarity in the viscous sublayer break down.

In moving from the realm of stationary wing flight towards the complexity of flapping wing flight as evolved in birds, we wish to introduce the simplest means of flapping as a first step in an attempt to simplify as much as possible our wind tunnel model and also to confine our attention to the dominant thrust producing mechanism. Our model half wings flap only in the plane normal to flight. The flapping motion is sinusoidal with time and symmetrical about the mid position (Fig. 6). No wing bending was allowed. The wing section shape had no camber and also was rigid in shape but free to twist in torsion about its shear centre. However, the model root support was fixed and therefore could not simulate vertical plunging of a bird associated with ideal elliptic span loading (Ref. 1).