During the past few years, there has been an increasing demand in thefield of precision engineering for fine motion in multi-degrees of freedomsystems. These applications motivated the development of a new robotics fieldcalled microrobotics. In this paper, we review both the design guidelines formicrorobots and the advantages of using parallel robots in very high precisionapplications. Parallel micromanipulators using elastic joints as well asstructures manufactured in single solid and metallic bellows areintroduced.

Finding optimal paths for robot navigation in a known terrain has been studied for some time but, in many important situations, a robot would be required to navigate in completely new or partially explored terrain. We propose a method of robot navigation which requires no pre-learned model, makes maximal use of available information, records and synthesizes information from multiple journeys, and contains concepts of learning that allow for continuous transition from local to global path optimality. The model of the terrain consists of a spatial graph and a Voronoi diagram. Using acquired sensor data, polygonal boundaries containing perceived obstacles shrink to approximate the actual obstacles surfaces, free space for transit is correspondingly enlarged, and additional nodes and edges are recorded based on path intersections and stop points. Navigation planning is gradually accelerated with experience since improved global map information minimizes the need for further sensor data acquisition. Our method currently assumes obstacle locations are unchanging, navigation can be successfully conducted using two-dimensional projections, and sensor information is precise.

An adaptive computed torque (ACT) controller in the task space is proposed for the trajectory tracking of a parallel manipulator with redundant actuation. The dynamic model, including the active joint friction, is established in the task space for the parallel manipulator, and the linear parameterization expression with respect to the dynamic and friction parameters is formulated. On the basis of the dynamic model, a new control law, which contains adaptive dynamics compensation, friction compensation, and tracking error elimination terms, is designed. After defining the state-space model of the error system, the parameter adaptation law is derived by using the Lyapunov method, and the convergence of the tracking error and the error rate is proved by using the Barbalat's lemma. The ACT controller is implemented in the trajectory tracking experiments of an actual 2-DOF parallel manipulator with redundant actuation, and the experiment results are compared with the computed torque controller.

This paper describes external camera-based shape estimation for continuum robots. Continuum robots have a continuous backbone made of sections which bend to produce changes of configuration. A major difficulty with continuum robots is the determination of the robot's shape, as there are no discrete joints. This paper presents a method for shape determination based on machine vision. Using an engineered environment and image processing from a high speed camera, shape determination of a continuum robot is achieved. Experimental results showing the effectiveness of the technique on our Elephant's Trunk Manipulator are presented.

This paper presents a simplified kinematics propulsive model for carangiform propulsion. The carangiform motion is modeled as a serial $N$-joint oscillating mechanism that is composed of two basic components: the streamlined fish body represented by a planar spline curve and its lunate caudal tail by an oscillating foil. The speed of fish's straight swimming is adjusted by modulating the joint's oscillatory frequency, and its orientation is tuned by different joint's deflections. The experimental results showed that the proposed simplified propulsive model could be a viable candidate for application in aquatic swimming vehicles.

In this paper, autonomous motion control approaches to generate the coordinated motion of a dual-arm space robot for target capturing are presented. Two typical cases are studied: (a) The coordinated dual-arm capturing of a moving target when the base is free-floating; (b) one arm is used for target capturing, and the other for keeping the base fixed inertially. Instead of solving all the variables in a unified differential equation, the solution equation of the first case is simplified into two sub-equations and practical methods are used to solve them. Therefore, the computation loads are largely reduced, and feasible trajectories can be determined. For the second case, we propose to deal with the linear and angular momentums of the system separately. The linear momentum conservation equation is used to design the configuration and the mounted pose of a balance arm to keep the inertial position of the base's center of mass, and the angular momentum conservation equation is used to estimate the desired momentum generated by the reaction wheels for maintaining the inertial attitude of the base. Finally, two typical tasks are simulated. Simulation results verify the corresponding approaches.

This paper proposed a novel three degree of freedom (DOF) parallel manipulator—two translations and one rotation. The mobility study and inverse kinematic analysis are conducted, and a CAD model is presented showing the design features. The optimization techniques based on artificial intelligence approaches are investigated to improve the system stiffness of the proposed 3-DOF parallel manipulator. Genetic algorithms and artificial neural networks are implemented as the intelligent optimization methods for the stiffness synthesis. The mean value and the standard deviation of the global stiffness distribution are proposed as the design indices. Both the single objective and multi-objective optimization issues are addressed. The effectiveness of this methodology is validated with Matlab.

CaPaMan (Cassino Parallel Manipulator) is a 3-Degree Of Freedom spatial parallel manipulator that has been designed at the Laboratory of Robotics and Mechatronics, in Cassino. In this paper we present a formulation for an optimum design for CaPaMan architecture when the orientation workspace is suitably specified.

In the literature, 3-RRPRR architectures were proposed to obtain pure translation manipulators. Moreover, the geometric conditions, which 3-RRPRR architectures must match, in order to make the end-effector (platform) perform infinitesimal (elementary) spherical motion were enunciated. The ability to perform elementary spherical motion is a necessary but not sufficient condition to conclude that the platform is bound to accomplish finite spherical motion, i.e. that the mechanism is a spherical parallel manipulator (parallel wrist). This paper demonstrates that the 3-RRPRR architectures matching the geometric conditions for elementary spherical motion make the platform accomplish finite spherical motion, i.e. they are parallel wrists (3-RRPRR wrist), provided that some singular configurations, named translation singularities, are not reached. Moreover, it shows that 3-RRPRR wrists belong to a family of parallel wrists which share the same analytic expression of the constraints which the legs impose on the platform. Finally, the condition that identifies all the translation singularities of the mechanisms of this family is found and geometrically interpreted. The result of this analysis is that the translation singularity locus can be represented by a surface (singularity surface) in the configuration space of the mechanism. Singularity surfaces drawn by exploiting the given condition are useful tools in designing these wrists.

We studied the pressure patterns in the residual limbs of transradial amputees during their voluntary commands for finger taps. Topographic maps of pressures exerted against the hard prosthetic socket were registered with an array of 32 pressure sensors, to produce residual kinetic images (RKIs) of the limb. Results with 2 untrained subjects demonstrated that RKIs are reliable decoders of efferent commands. Coupled with a trained filter, RKIs can provide biomimetic control over multiple degrees of freedom.

A new kinematic design of a parallel spherical wrist with actuatorredundancy is presented. A special feature of this parallel manipulator is thearrangement of co-axial actuators which allows unlimited rotation about any axisinside a cone-shaped workspace. A detailed kinematic analysis has shown thatactuator redundancy not only removes singularities but also increases workspacewhile improving dexterity. The structure optimization has been performed with aglobal dexterity criterion. Using a conditioning measure, a comparison with anon-redundant structure of the same type was performed and shows that asignificant improvement in dexterity has been obtained.

This paper deals with an optimum synthesis of planar parallel manipulators using two constrained optimisation procedures based on the minimization of: (i) the overall deviation of the condition number of manipulator Jacobian matrix from the ideal/isotropic condition number, and (ii) bearing forces throughout the manipulator workspace for force balancing. A revolute jointed planar parallel manipulator is used as an example to demonstrate the methodology. The parameters describing the manipulator geometry are obtained from the first optimisation procedure, and subsequently, the mass distribution parameters of the manipulator are determined from the second optimisation procedure based on force balancing. Optimisation results indicate that the proposed optimisation approach is systematic, versatile and easy to implement for the optimum synthesis of the parallel manipulator and other kinematic chains. This work contributes to previously published work from the point of view of being a systematic approach to the optimum synthesis of parallel manipulators, which is currently lacking in the literature.

This paper presents a bipedal locomotion model for passive dynamic walking with flat feet and compliant ankles. The two-dimensional seven-link model extends the simplest walking model with the addition of hip actuation, knee joints, flat feet and torsional springs based compliance on ankle joints, concerning heel-strike and toe-strike transitions, to achieve adaptive bipedal locomotion on level ground with controllable walking speed. We investigate the effects of foot geometric parameters and ankles stiffness on bipedal walking. The model achieves satisfactory walking results not only on even ground but also on uneven terrain with no active control and on different walking velocities. In addition, from the view of stability, there is an optimal foot-ankle ratio of the passivity-based walker. The results can be used to explore further understanding of bipedal walking, and help the design of future intelligent ankle-foot prosthesis and passivity-based robot prototypes towards more practical uses.

For robotic manipulators that are redundant or with high degrees of freedom (dof), an analytical solution to the inverse kinematics is very difficult or impossible. Pioneer 2 robotic arm (P2Arm) is a recently developed and widely used 5-dof manipulator. There is no effective solution to its inverse kinematics to date. This paper presents a first complete analytical solution to the inverse kinematics of the P2Arm, which makes it possible to control the arm to any reachable position in an unstructured environment. The strategies developed in this paper could also be useful for solving the inverse kinematics problem of other types of robotic arms.

This paper proposes a simple fuzzy sliding mode control to achieve the best trajectory tracking for the robot manipulator. In the core of the proposed method, by applying the feedback linearization technique, the known dynamics of the robot's manipulator is removed; then, in order to overcome the remaining uncertainties, a classic sliding mode control is designed. Afterward, by applying the TS fuzzy model, the classic sliding mode controller is converted to fuzzy sliding mode controller with very simple rule base. The mathematical analysis shows that the robot manipulator with the new proposed control in tracking the robot manipulator in presence of uncertainties has the globally asymptotic stability. Finally, to show the performance of the proposed method, the controller is simulated on a robot manipulator with two degrees of freedom as case study of the research. Simulation results demonstrate the superiority of the proposed control scheme in presence of the structured and unstructured uncertainties.

This paper discusses the application of a constraint-based model predictive control (MPC) to mobile manipulation tracking problems. The problem has been formulated so as to guarantee offset-free tracking of piecewise constant references, with convergence and recursive feasibility guarantees. Since MPC inputs are recomputed at every control iteration, it is possible to deal with dynamic and unknown scenarios. A number of motion constraints can also be easily included: Acceleration, velocity and position constraints have been enforced, together with collision avoidance constraints for the mobile base and the arm and field-of-view constraints. Such constraints have been extended over the prediction horizon maintaining a linear-quadratic formulation of the problem. Navigation performance has been improved by devising an online algorithm that includes an additional goal to the problem, derived from the classical vortex field approach. Experimental validation shows the applicability of the proposed approach.

Lie algebra is an area of mathematics that is largely used by electrical engineer students, mainly at post-graduation level in the control area. The purpose of this paper is to illustrate the use of Lie algebra to control nonlinear systems, essentially in the framework of mobile robot control. The study of path following control of a mobile robot using an input-output feedback linearization controller is performed. The effectiveness of the nonlinear controller is illustrated with simulation examples.

This paper investigates task allocation for multiple robots by applying the game theory-based negotiation approach. Based on the initial task allocation using a contract net-based approach, a new method to select the negotiation robots and construct the negotiation set is proposed by employing the utility functions. A negotiation mechanism suitable for the decentralized task allocation is also presented. Then, a game theory-based negotiation strategy is proposed to achieve the Pareto-optimal solution for the task reallocation. Extensive simulation results are provided to show that the task allocation solutions after the negotiation are better than the initial contract net-based allocation. In addition, experimental results are further presented to show the effectiveness of the approach presented.

This paper presents a novel trajectory planning method for a flexible Cartesian robot manipulator in a point-to-point motion. In order to obtain an exact mathematical model, the parameters of the equation of motion are determined from an identification experiment. An artificial neural network is employed to generate the desired base position, and then, a particle swarm optimization technique is used as the learning algorithm, in which the sum of the displacements of the manipulator is chosen as the objective function. We show that the residual vibrations of the manipulator can be suppressed by minimizing the displacement of the manipulator. The effectiveness and validity of the proposed method are demonstrated by comparing the simulation and experimental results.

Several static and dynamic stability criteria have been defined in the course of walking-robot history. Nevertheless, previous work on the classification of stability criteria for statically stable walking machines (having at least four legs) reveals that there is no stability margin that accurately predicts robot stability when inertial and manipulation effects are significant. In such cases, every momentum-based stability margin fails. The use of an unsuitable stability criterion yields unavoidable errors in the control of walking robots. Moreover, inertial and manipulation effects usually appear in the motion of these robots when they are used for services or industrial applications. A new stability margin that accurately measures robot stability considering dynamic effects arising during motion is proposed in this paper. The new stability margin is proven to be the only exact stability margin when robot dynamics and manipulation forces exist. Numerical comparison has been conducted to support the margin's suitability. Stability-level curves are also presented on the basis of a suitable stability margin to control the trajectory of the center of gravity during the support phase.