This paper presents a novel Cobotic system with differential CVT. The new system is significantly cheaper, simpler to control and more efficient than Cobots with S-CVTs. Both path-guidance and power-assist functions can be simply realized with the new system. Basic structures, kinematic and dynamic models, as well as control algorithms, which are essential for design, control synthesis and control of the system, are briefly presented in the paper.

In this paper, control of nonlinear teleoperator systems where both the master and slave systems are kinematically redundant robot manipulators is addressed. The controller is developed under the assumption that the user and environmental input forces are unmeasurable. Lyapunov-based stability analysis is used to prove that the proposed controller yields asymptotic tracking results and ensures the coordination of the master and slave systems while satisfying a sub-task objective. Numerical simulation results are presented to illustrate the effectiveness of the proposed controller.

We introduce a novel probabilistic algorithm (CPRM) for real-time motion planning in the configuration space ${\EuScript C}$. Our algorithm differs from a probabilistic road map (PRM) algorithm in the motion between a pair of anchoring points (local planner) which takes place on the boundary of the obstacle subspace ${\EuScript O}$. We define a varying potential field f on ∂${\EuScript O}$ as a Morse function and follow $\vec{\nabla} f$. We then exemplify our algorithm on a redundant worm climbing robot with n degrees of freedom and compare our algorithm running results with those of the PRM.

In this paper, we develop a force display system using parallel wire mechanism for virtual sports training with high speed motion. We firstly point out a control issue of the force display system driven by parallel wire mechanism. Based on the analysis, control laws are proposed to improve performance of the force display system. It is experimentally demonstrated that the proposed control laws realize higher acceleration and lower reaction force than other force display systems. Using the experimental result, the performance of the system is evaluated quantitatively.

This paper presents the work on developing a sliding-leg tripod as a programmable add-on device for manufacturing. The purpose is to enhance the capabilities of any machine by providing it with a more flexible range of motion. This device can be used as a toolhead for CNC machine tools and robots, or as a work stage for coordinate measuring machines and laser scanning systems. In this paper, system modelling, analysis and control of this device is presented. System modeling includes mobility study, kinematic model and inverse kinematics. System analysis includes workspace analysis, transmission ratio and stiffness analysis. System control includes path planning, joint space control and Cartesian space prediction. It is shown that the proposed device can provide flexibility and dexterity to machines.

This work is dedicated to the analysis of the application of active impedance control for the realisation of three objectives simultaneously: velocity regulation in free motion, impact attenuation and finally force tracking. At first, a brief analysis of active impedance control is made, deducing the value of each parameter in order to achieve the three objectives. It is demonstrated that the system may be made overdamped with the adequate selection of the parameters if the characteristics of the environment are known, avoiding high overshoots of force during the impact. The second and most important contribution of this work is an additional measure for impact control in the case when the characteristics of the environment are unknown. It consists in switching among different values of the parameters of the impedance in order to dissipate faster the energy of the system, limiting the peaks of force and avoiding losses of contact. The optimal switching criteria are deduced for every parameter in order to dissipate the energy of the system as fast as possible. The results are verified in simulation.

An S-R-S (Spherical-Revolute-Spherical) redundant manipulator is similar to a human arm and is often used to perform dexterous tasks. To solve the inverse kinematics analytically, the arm-angle was usually used to parameterise the self-motion. However, the previous studies have had shortcomings; some methods cannot avoid algorithm singularity and some are unsuitable for configuration control because they use a temporary reference plane. In this paper, we propose a method of analytical inverse kinematics resolution based on dual arm-angle parameterisation. By making use of two orthogonal vectors to define two absolute reference planes, we obtain two arm angles that satisfy a specific condition. The algorithm singularity problem is avoided because there is always at least one arm angle to represent the redundancy. The dual arm angle method overcomes the shortcomings of traditional methods and retains the advantages of the arm angle. Another contribution of this paper is the derivation of the absolute reference attitude matrix, which is the key to the resolution of analytical inverse kinematics but has not been previously addressed. The simulation results for typical cases that include the algorithm singularity condition verified our method.

Hull cleaning before repainting is a key operation in the maintenance of ships. For more than a decade, a means to improve this operation has been sought through robotization and the use of different techniques such as grit blasting and ultra high pressure water jetting. Despite this, it continues to be standard practice in shipyards that this process is carried out manually. This paper presents a family of robots that aims to offer important improvements to the process as well as satisfying, to a great extent, all the operative requirements of efficiency, security, and respect for the environment that shipyards nowadays demand. It is described the family of devices with emphasis on the mechanical design. This set consists of two vertical robotic towers and a robot climber. In addition, it is shown the control architecture of the global system. Finally, operative results are presented together with a comparison between the performance achieved in shipyards through the use of these robots and those obtained with a manual process.

In this paper we propose a set of techniques for a real-time motion capture of a human body. The proposed motion capture system is based on low cost accelerometers, and is capable of identifying the body configuration by extracting gravity-related terms from the sensor data. One sensor unit is composed of 3 accelerometers arranged orthogonally to each other, and is capable of identifying 2 rotating angles of joints with 2 degrees of freedom. A geometric fusion technique is applied to cope with the uncertainty of sensor data. A practical calibration technique is also proposed to handle errors in aligning the sensing axis to the coordination axis. In the case where motion acceleration is not negligible compared with gravity acceleration, a compensation technique to extract gravity acceleration from the sensor data is proposed. Experimental results not only for individual techniques but also for human motion capturing with graphics are included.

A general method is presented to automatically determine the placement of manipulators which allows one to optimize multiple kinematic performances indices during the execution of their tasks. It considers the presence of obstacles in the workstation and constraints on the motion of the manipulator's joints. The complete formulation is included, and an example with a six-degree-of-freedom manipulator in a cluttered environment es solved that demonstrates the improvements achieved for the manipulator performances by applying the method.

This paper presents a novel kinematic approach for controlling the end-effector of a continuum robot for in-situ repair/inspection in restricted and hazardous environments. Forward and inverse kinematic (IK) models have been developed to control the last segment of the continuum robot for performing multi-axis processing tasks using the last six Degrees of Freedom (DoF). The forward kinematics (FK) is proposed using a combination of Euler angle representation and homogeneous matrices. Due to the redundancy of the system, different constraints are proposed to solve the IK for different cases; therefore, the IK model is solved for bending and direction angles between (−π/2 to +π/2) radians. In addition, a novel method to calculate the Jacobian matrix is proposed for this type of hyper-redundant kinematics. The error between the results calculated using the proposed Jacobian algorithm and using the partial derivative equations of the FK map (with respect to linear and angular velocity) is evaluated. The error between the two models is found to be insignificant, thus, the Jacobian is validated as a method of calculating the IK for six DoF.

We have made a systematic study of the gait of a straight leg planar passive walking model through simulations and experiments. Three normalised parameters, which represent the foot radius, the position of the mass centre and the moment of inertia, are used to characterise the walking model.

In the simulation, we have obtained the fixed points and the basins of attraction of the walking models with different parameter combinations by the aid of the cell mapping method. With the results of fixed points, we investigated the effects of parameter variations on the gait descriptors, including step length, period, average speed and energy inefficiency. A model that has a large basin of attraction has been obtained, and it can start walking far from its fixed point. However, the size of the basin of attraction is not a good measurement of robustness. Thus, we proposed floors with random slope angles or stairs with random heights to test robustness. Five hundred times of simulations with 100 non-dimensional time units were implemented for each parameter combination. The times that the walker failed to arrive at the end were recorded. The simulation results showed that the model with a larger foot radius and higher position of mass centre has a lower possibility of falling on uneven floors. A large moment of inertia is helpful for walking on a random slope angle floor, while low values of moment of inertia are good for navigating random stairs.

Prototype experiments have validated the simulation results, which showed that models with larger feet have a longer step length and high speed. However, period differences were difficult to obtain in the experiments since the differences were very small. We have tested the sensitivity with the initial conditions of the models with different foot radii on a flat floor, and have also tested the robustness of the models on a floor with random slope angles. The times that the model reached the end of the floor were recorded. The experimental results showed that a large foot radius is good for improving the basin of attraction and robustness on uneven floors. Finally, the exceptions of the experiment are explained.

This paper concerns the issue of mechanism design of a simplified 6-DOF 6-RUS parallel manipulator. The design of robotic mechanisms, especially for 6-DOF parallel manipulators, is an important and challenging problem in the field of robotics. This paper presents a design method for robotic mechanisms, which is based on the physical model of the solution space. The physical model of the solution space, which can transfer a multi-dimensional problem to a two or three-dimensional one, is a useful tool to obtain all kinds of performance atlases. In this paper, the physical model of the solution space for spatial 6-RUS (R stands for revolute joint, U universal joint and S spherical joint) parallel manipulators is established. The atlases of performances, such as workspace and global conditioning index, are plotted in the physical model of the solution space. The atlases are useful for the mechanism design of the 6-RUS parallel manipulators. The technique used in this paper can be applied to the design of other robots.

This paper analyses the concept of velocity isotropy for Parallel Mechanisms with Actuation Redundancy (PMAR). The limits of classical indices based on the Jacobean matrix condition number are shown. It is proposed to use either the largest ellipsoid included in the operational polytop, or the operational polytop itself, as better representations of a PMAR capabilities. The polytop is studied because it is actually the accurate representation of a machine capability, while the largest ellipsoid remains similar to the classical tool roboticists are dealing with for decades. Velocity performance indices are proposed, and the ways to compute them efficiently are given.

This paper presents a persistent method for the identification problem of open-chained robotic systems. Based on the Projection Equation, a new, direct method to collect the dynamic and friction parameters in linear form is worked out. However, in this form, linear dependencies in the parameters occur and they are canceled out with the help of the QR algorithm. The obtained linear independent parameters are the base parameters of the system. To ensure a good excitation, the identification is improved by using optimized trajectories defined by Fourier-series, taking also physical constraints into account. The evaluation of the dynamic robot parameters is realized with a least squares error optimization. Furthermore, the result strongly depends on a special choice of weighting matrices for the error. Experimental results for a seven-axes robotic system (standard six-axes industrial manipulator mounted on a linear axis) are presented in detail. Additionally, the influence of temperature effects to base parameter changes is discussed.

We present a general framework for modeling a class of mechanical systems for robotic manipulation, consisting of articulated limbs with redundant tendinous actuation and unilateral constraints. Such systems, that include biomorphically designed devices, are regarded as a collection of rigid bodies, inter-acting through connections that model both joints and contacts with virtual springs. Methods previously developed for the analysis of force distribution in multiple whole-limb manipulation are generalized to this broader class of mechanisms, and are shown to provide a basis for the control of co-contraction and internal forces that guarantee proper operation of the system. In particular, in the presence of constraints such as those due to limited friction between surfaces or object fragility, the choice of tendon tensions is crucial to the success of manipulation. An algorithm is described that allows to evaluate efficiently set-points for the control of tendon actuators that “optimally” (in a sense to be described) comply with the given constraints.

This paper presents research work which crosses the divide between “Path Planning” and “Trajectory Generation & Tracking”. These subjects have tended to develop along two parallel lines, in isolation from each other. The work uses the Lagrange formulation for the three major joints of an industrial manipulator. Simple planning rules are developed from this formulation. The rules are used to select new paths for a manipulator rather than to improve preplanned trajectories. The method has been applied to pick and place tasks requiring gross motions of the manipulator and the results are presented. It is shown that using this method, pre-planned manipulator paths can be modified to improve the gross motions associated with the pick and place task.

A novel 3-DOF prismatic-revolute-cylindrical (PRC) translational compliant parallel micromanipulator (CPM) has been designed for 3-D nanomanipulation in this paper. The system is configured by a proper selection of hardware and analyzed via the established pseudo-rigid-body (PRB) model. The CPM workspace is determined taking into account the physical constraints imposed by piezoelectric actuators and flexure hinges.

The state-of-the-art FastSLAM algorithm has been shown to cause a particle depletion problem while performing simultaneous localization and mapping for mobile robots. As a result, it always produces over-confident estimates of uncertainty as time progresses. This particle depletion problem is mainly due to the resampling process in FastSLAM, which tends to eliminate particles with low weights. Therefore, the number of particles to conduct loop-closure decreases, which makes the performance of FastSLAM degenerate. The resampling process has not been thoroughly analyzed even though it is the main reason for the particle depletion problem. In this paper, standard resampling algorithms (systematic residual and partial resampling), a rank-based resampling adopting genetic algorithms are analyzed using computer simulations. Several performance measures such as the effective sample size, the number of distinct particles, estimation errors, and complexity are used for the thorough analysis of the resampling algorithms. Moreover, a new compensation technique is proposed instead of resampling to resolve the particle depletion problem in FastSLAM. In estimation errors, the compensation technique outperformed other resampling algorithms though its run-time was longer than those of others. The most appropriate time to instigate compensation to reduce the run-time was also analyzed with the diminishing number of particles.

This paper describes the use of a hybrid system comprising a multi-layer perceptron and a Petri Net model to control the navigation of multiple mobile robots in an unknown and cluttered environment. The multi-layer perceptron is trained with examples representing the typical static obstacles to be encountered by the robots and the evasive actions to be taken. The Petri Net model embodies the rules describing how the robots should move in order to avoid colliding against one another. The hybrid system has been implemented in simulation software as well as in actual mobile robots. The paper presents the results of simulation and practical tests that demonstrate the ability of groups of robots incorporating the proposed navigation system to negotiate various types of obstacles and find targets successfully.